EMC Celerra NS40 Manuals

Install Rails and Components in Rack Setting Up the EMC® Celerra® NS40 System Before You Begin 1 1 2a Install Blade Enclosure 300-004-901 Rev A01 Copyright © 2007 EMC Corporation. All rights reserved. 2c Install Control Station 2b Install Storage Processor Enclosure LAN1 LAN2 Front CIP-000935 Disk-array enclosure Standby power supply Control Station Storage processor enclosure Blade enclosure Shipping Rack Before you begin: • The NS40 system you are about to install comes factory pre-loaded with Celerra Network Server software (DART) and Storage Array software (FLARE). DO NOT PERFORM A FRESH INSTALL OF SOFTWARE. If a software upgrade (not fresh install) is required, perform it after installation. For more information refer to Solution Case emc163262. • Go to the Celerra Tools page for the latest information on the NS40 product: (http://Powerlink.EMC.com and select Celerra Tools in the Navigator). • Two people are required to lift several hardware components. When installing the disk-array enclosures in the cabinet, do not remove the disks. • Remove only the 16 visible Phillips-head screws on the front of the mini-rack. Do not remove any of the other screws or you may injure yourself or damage the equipment. Alignment pin Rear Front Adjustable rail Alignment pin Right rear Mounting rail Screw (2) Alignment pin CIP-000921 Right front Screw Mounting rail Rear Front Enclosure CIP-000922 Rear Front Enclosure CIP-000923 Rail catch Screw (2 per side) Bezel Indentation to center of the rack 2 4 1. Select 7U (12.25 in.) of available rack space for the NS40, plus 3U (5.25 in.) for each optional disk-array enclosure (1U =1.75 inches). NOTE: Use the supplied clip nuts if required for your rack. 2. Starting at the bottom of the selected rack space, mount one set of 1U rails for the blade enclosure as follows: a. From the cabinet front, insert the rail alignment pin into the middle hole of the 1U space on the right side at the the rear of the cabinet. Orient the rails so the sliding insert faces the inside of the rack. b. Extend the rail to the front of cabinet, aligning the rail holes with the channel holes (the verticle metal bar with evenly spaced holes) on the inside of the cabinet. Always ensure the rail is level. c. Install but do not tighten one of the provided screws in the top hole on the front of the rail through the cabinet channel. d. From the cabinet rear, insert but do not tighten two screws in the top and bottom holes on the rail back through the cabinet channel. e. Repeat steps b-e to install the left rail. 3. Two people are required for this installation: From the cabinet front, align the blade enclosure with the mounting channels. With the help of another person, slowly slide the blade enclosure into the rails until the front assembly flanges are flush with the cabinet channels. 4. Do not insert any new screws, but tighten the screws on each end securing the mounting rails to the cabinet channels. 5. Insert two of the provided screws into the middle and bottom holes of each rail catch. Attach the bezel rail catches to the holes in the rail flanges on the front of the cabinet. Then press the bezel onto the rail catches until it snaps into place. 1. In the 1U space above the blade enclosure, install the storage processor enclosure as described in Step 2a Install Blade Enclosure. NOTE: Do not remove the Control Station label at this time. 1. In the 1U space above the storage processor enclosure, install the Control Station as described in Step 2a Install Blade Enclosure. 2 3 Required parts: • Blade enclosure number for the NS40 single blade P/N 100-520-326 or 100-520-328 or dual blade P/N 100-520-327 or 100-520-329 • Adjustable rail kit P/N 100-561-802 • Bezel Required parts: • Storage processor enclosure for the NS40 P/N 100-520-372 • Rail kit P/N 100-561-802 Required parts: • Control Station P/N 100-520-606 • Rail kit P/N 100-520-527 • Adjustable Rail Installation kit B A Blade 3 (B 3) Blade enclosure SP A B 2 CIP-000914 SP B Storage processor enclosure B A Blade 3 (B 3) Blade enclosure SP A B 2 CIP-000915 SP B Control Station Storage processor enclosure Required tools: • Flathead screwdriver • Manual Phillips-head screwdriver Avoid stripping the screw-heads.