Encore ENLWI-G2 Manuals

ENLWI-G2 ENCORE 802.11g Wireless PCI Adapter User’s Manual FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. 1 CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B for ITE, the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: All trade names and trademarks are the properties of their respective companies. Copyright © Encore Electronics, Inc. 2007, All Rights Reserved. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法 規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用 電波輻射性電機設備之干擾。 2

Wireless 802.11g 54Mbps PCI Adapter ENLWI-G2 Product Description The ENLWI-G2 is a fully functional IEEE 2.4 GHz 802.11G device capable of transferring at speeds up to 54Mbps for up to 100 feet. This adapter is fully compatible with 802.11G and 802.11B devices. WEP, WPA and WPA2 encryption protects your network and keeps intruders out. Supports both Ad-Hoc and Infrastructure modes. Compatible with 32-bit and 64-bit PCI bus. Achieve the best possible connection with Dynamic rate shifting technology. Convert your desktops to wireless workstations. Wireless technology eliminates the hassle of running Ethernet wires around the office or home. Share MP3s, digital video, documents, files and even the internet at blazing 54Mbps wireless speed. No need to rewire Ethernet cables when moving around PCs. Support most Windows operating systems (Windows® 98SE/ME/2000/XP). Product Features • Compatible with IEEE 802.11g high rate standard to provide wireless Ethernet speeds of 54Mbps data rate • Dynamic date rate scaling at 54, 48, 36, 24, 18, 12, 9 and 6Mbps for 802.11g • Dynamic date rate scaling at 11, 5.5, 2 and 1Mbps for 802.11b • Maximum reliability, throughput and connectivity with automatic data rate switching • Supports wireless data encryption with 64/128-bit WEP standard for security, Supports WPA, WPA-PSK, WPA2, WPA2-PSK • Supports 32-bit PCI interface slot for Desktop PC • Drivers support Windows 98, 2000, ME and XP • Simple user setup & diagnostics utilities Type approval compliant with FCC Part 15.247 for US, ETS 300 328 for Europe Product Specifications Radio Technology IEEE 802.11g Orthogonal Frequency Division Multiplexing (OFDM) IEEE 802.11b Direct Sequence Spread Spectrum (DSSS) Interface 32-bit PCI interface Transmission Rate 1, 2, 5.5, 6, 11, 12, 18, 22, 24, 36, 48, 54Mbps (auto sense) Receiver Sensitivity 54Mbps: Typical -73dBm @ 10% PER 11Mbps: Typical -85dBm @ 8% PER Wireless LAN Frequency Range 2412 ~ 2484 MHz ISM band (channels 1 ~ 14) Modulation Schemes DBPSK/DQPSK/CCK/OFDM Media Access Protocol CSMA/CA with ACK Transmit Power Minimum 15dBm typically @ 802.11b Minimum 12dBm typically @ 802.11g Channel USA: 11 Europe: 13 Japan: 14 Driver Support Windows® 98(SE)/2000/ME/XP Security 64/128-bits WEP Encryption Wireless Fidelity Protected Access (WPA, WPA2) Range Coverage Indoor: 35 ~ 100 meters (depends on environment) Outdoor: 100 ~ 300 meters (depends on environment) Roaming Full mobility and seamless roaming from cell to cell Continuous Current Consumption 240mA typ. for receive mode 530mA typ. for transmit mode Diagnostic LEDs Link status Dimensions (W x H x D) 133 x 121 x 21.6 mm (without antenna) Operation Temperature 0 ~ 40 oC Storage Temperature -10 ~ 70 oC Humidity 10% ~ 95% RH, no condensation Certifications FCC Part 15.247 for US ETS 300 328 for Europe Encore Electronics WWW.ENCORE-USA.COM ENLWI-G2

ENLWI-G2 / ENPWI-G2 802.11g Wireless LAN Adapter User’s Guide Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments for example: ·On board of airplanes, or ·In an explosive environment, or ·In case the interference risk to other devices or services is perceived or identified as harmful In case the policy regarding the use of Wireless LAN devices in specific organizations or environments (e.g. airports, hospitals, chemical/oil/gas industrial plants, private buildings etc.) is not clear, please ask for authorization to use these devices prior to operating the equipment. Regulatory Information/disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The Manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, of the substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. USA-FCC (Federal Communications Commission) statement This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of this device. i FCC Radio Frequency Exposure statement This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation is minimized. When nearby persons has to be kept to ensure RF exposure compliance, in order to comply with RF exposure limits established in the ANSI C95.1 standards, the distance between the antennas and the user should not be less than 20 cm. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the distance between the equipment and the receiver. 3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. Export restrictions This product or software contains encryption code that may not be exported or transferred from the US of Canada without an approved US Department of Commerce export license. ii