EnerSys OutBack POWER Mojave OGHI8048A Manuals

Quick Start Guide Warranty The warranty for this product can be downloaded from www.outbackpower.com/downloads/warranty_and_safety/warranty_mojave A copy is available by sending a self-addressed envelope to this address: Contact Information Mailing 7360 – South Kyrene Road Address: Tempe, AZ 85283 USA Web Site: www.outbackpower.com NOTE: Additional information on this product is available at www.outbackpower.com. For user interface (UI) navigation, programming, and troubleshooting, see the Mojave Operator’s Manual. Date and Revision August 2021, Revision A Listings: o UL® 1741 2nd Edition with SA o CSA C22.2, No. 107.1-16 Ed:4 Certifications: o IEEE® 1547 o IEEE 1547.1 System Grounding and Bonding: In this product, the AC and battery circuits are isolated from the enclosure. Equipment grounding is required by Section 250 of the National Electric Code (ANSI/NFPA® 70) and Canadian Electrical Code (C22.1). Overcurrent Protection o Battery disconnection and overcurrent protection are not provided in the wiring compartment. The installer must provide protection for the battery circuit according to the following parameters.  Maximum 250 Adc  Minimum 10 kA AIC  Listed to UL 489 o The wiring compartment provides AC overcurrent protection for the utility grid input.  60 Aac  Listed to UL 489 for AC output and utility grid 120/240 Vac circuits  Recognized to UL 1077 for generator 120/240 Vac circuits o DIN rail space is provided for circuit breakers for a generator, if installed. See Wiring. Environmental Ratings: o Environmental : NEMA Type 1 (Ingress Protection 2X) o Ambient Temperature Range (operating): –20°C to 50°C Dimensions and Weight: o Height 37.75" (95.9 cm) o Width 15.87" (40.3 cm) Electrical Specifications o Maximum continuous output: 8000 VA @ 40°C o Nominal input and output voltage: 120/240 Vac o Nominal frequency: 60 Hz o Nominal grid voltage range: 211.2 to 264 Vac o Maximum continuous output current  Grid-tied: 32 Aac  Off-grid: 34 Aac o Maximum grid input current: 55 Aac o Maximum generator input current: 55 Aac o AUX output: 0.8 A @12 Vdc o AUX relay: 4 A @250 Vac and 30 Vdc o Nominal battery voltage: 48 Vdc o Maximum battery input current: 200 Adc o Maximum battery charging current: 170 Adc o Battery input voltage range: 40 to 60 Vdc o Charging output voltage range: 40 to 64 Vdc Supported Batteries o Supports most 48-Vdc lead-acid batteries; consult battery manufacturer for recommended settings o Specified lithium-ion batteries; see list of qualified batteries at www.outbackpower.com CAUTION: To reduce the risk of fire, connect only to a circuit provided with a 60 amperes maximum branch-circuit protection in accordance with the National Electric Code, ANSI/NFPA 70. ! 900-00273-01-001 REV A ©2021 OutBack Power. All Rights Reserved. Do not copy or distribute without permission. Specifications Included in Box: o Mojave inverter o Product installation literature o Safety statement o Wi-fi antenna o Ground-bonding conductor o Mounting bracket o Hardware kit o Current transducers Tools Needed: o Socket wrench  7/16" socket 7 mm socket o Socket wrench, torque 13 mm socket o Screwdriver, #2 Phillips o Screwdriver, torque #2 Phillips Flat blade Features: A. Indicator light B. Wi-fi antenna C. Wiring compartment D. Vent B 37.75" (95.9 cm) 15.87" (40.3 cm) 11.0" (27.9 cm) 0.22" (0.6 cm) A C D B Mojave™ Grid-Hybrid Inverter/Charger OGHI8048A CAUTION: Battery Damage OutBack Power does not approve custom applications, including installation of lithium-ion batteries that have not been published as installable with OutBack Power equipment. See the Mojave Operator’s Manual for more information. ! WARNING: Burn Hazard The vents (the sides of the product; see D) may give off heated air. Install this product so that casual contact does not occur. WARNING: Fire/Explosion Hazard Do not place combustible or flammable materials within 12 feet (3.7 m) of the equipment. This unit employs mechanical relays and is not ignition- protected. Fumes or spills from flammable materials could be ignited by sparks. WARNING: Personal Injury Use safe lifting techniques and standard safety equipment when working with this equipment. IMPORTANT: Read all safety instructions before proceeding. IMPORTANT:  This document is for use by qualified personnel familiar with energy storage systems (ESS) and basic inverter functionality. Users of this document should meet all local and governmental code requirements for licensing and training for the installation of electrical power systems with AC and DC voltage up to 600 volts. This product is only serviceable by qualified personnel.  Clearance and access requirements may vary by location.  Allow 8" (20.3 cm) on either side of the unit for ventilation.  A 36” (91.4 cm) clear space in front of the system for access is recommended.  Consult local electric code to confirm clearance and access requirements for the specific location. If this product is installed or used in a manner other than specified, the protection it provides may be impaired.  This inverter is for use in backup power and AC-coupled applications. Use with independent solar charge controllers is not supported at this time.  This product is designed and tested for stationary applications only. It is not listed or warranted for mobile use. o Depth 11.22" (28.5 cm) o Weight 133.0 lb (60.3 kg) IMPORTANT: Not intended for use with life support equipment. Trademarks and logos are the property of EnerSys and its affiliates unless otherwise noted. Subject to revisions without prior notice. E. & O.E. UL® is the registered trademark of UL LLC. IEEE® is the registered trademark of The Institute of Electrical and Electronics Engineers, Inc. NFPA® is the registered trademark of National Fire Protection Association, Inc.