EPH Controls A17 Manuals

CAUTION! Before commencing, disconnect the device from the mains. There are parts that carry mains voltage behind the cover. Never leave unsupervised when it is open. (Prevent non specialists and especially children from gaining access to it.) Never remove this product from the electrical baseplate. Disconnect from mains supply in the event of any damage to any buttons. Do not use sharp tools to push any button. A17 - 1 Zone Timeswitch Operating Instructions Page 1 of 2 Lower the cover on the front of the unit. Move the selector switch to the PROG SET position. You can now program the timeswitch. Press the ‘ ’ or ‘ ’ buttons to adjust the P1 ON time. Press the ‘OK’ button. Press the ‘ ’ or ‘ ’ buttons to adjust the P1 OFF time. Press the ‘OK’ button. Repeat this process to adjust the ON & OFF times for P2 & P3. When completed, move the selector switch to the RUN position. 4. Setting the date and time 1. Factory default settings 6. Adjusting the program settings 2. Factory program settings Program: 5/2D Backlight: On Keypad: Unlocked 3. Resetting the timeswitch Contents 1. Factory default settings 2. Factory program settings 3. Resetting the timeswitch 4. Setting the date and time 5. ON/OFF period selection 6. Adjusting the program settings 7. Copy function 8. Reviewing the program settings 9. +1HR function 10. Advance function 11. Holiday mode 12. Backlight mode selection 13. Keypad lock and unlock This 1 zone timeswitch is designed to provide ON/OFF control for 1 zone. It is necessary to press the ‘RESET’ button prior to initial programming. This button is located behind the cover on the front of the unit. Press the ‘RESET’ button. ‘rst No’ appears on the screen. Press ‘+’ and Press ‘OK’. The timeswitch is now ready to be programmed. Lower the cover on the front of the unit. Move the selector switch to the CLOCK SET position. Press the ‘ ’ or ‘ ’ buttons to select the day. Press the ‘OK’ button. Press the ‘ ’ or ‘ ’ buttons to select the month. Press the ‘OK’ button. Press the ‘ ’ or ‘ ’ buttons to select the year. Press the ‘OK’ button. Press the ‘ ’ or ‘ ’ buttons to select the hour. Press the ‘OK’ button. Press the ‘ ’ or ‘ ’ buttons to select the minute. Press the ‘OK’ button. Press the ‘ ’ or ‘ ’ buttons to select 5/2D, 7D or 24H Press the ‘OK’ button. The date, time and function are now set. Move the selector switch to the RUN position to run the program, or to the PROG SET position to change the program setting. AUTO The timeswitch operates 3 ‘ON/OFF’ periods per day. ALL DAY The timeswitch operates 1’ON/OFF’ period per day. This operates from the frst ON time to the third OFF time. ON The timeswitch is permanently on. **ON** OFF The timeswitch is permanently of. **OFF** Lower the cover on the front of the unit. By pressing the ‘ SELECT’ button, you can change between AUTO / ALL DAY / ON / OFF. 5. ON/OFF period selection There are 4 modes available on this timeswitch for users to choose for their individual application. 20171108_A17_OpIns_JW Important: Keep this document RUN CLOCK SET PROG SET Mon-Fri Sat-Sun 5/2D P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30 7:30 10:00 12:00 12:00 17:00 23:00 All 7 days 7D P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30 Everyday 24H P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30 RUN CLOCK SET PROG SET EPH Controls Ireland Sitecast Industrial Estate, Pouladuf, Cork, T12 W665, Ireland [email protected] www.ephcontrols.com Copy function may only be used if the timeswitch is in the 7d mode. Lower the cover on the front of the timeswitch. Move the selector switch to the PROG SET position. Set the ON & OFF times for the day of the week you wish to copy from. Press the ‘Holiday’ button for 2 seconds. The next day of the week will begin to fash. Press the ‘ ’ button to copy the ON & OFF times to this day. Press the ‘ ’ button to skip a day. ON & OFF times can be copied to multiple days by using the ‘ ’ button. Press the ‘OK’ button when copying has been completed. When completed, move the selector switch to the RUN position. RUN CLOCK SET PROG SET 7. Copy function