EPH Controls R27-HW Manuals

For use in normal environments. R27-HW - 2 Zone Programmer Installation Instructions Page 1 of 2 EPH Controls Ireland [email protected] www.ephcontrols.com EPH Controls UK [email protected] www.ephcontrols.co.uk 20180621_R27-HW_InsIns_JW This programmer can be mounted in the following ways: 1. Directly wall mounted 2. Mounted to a recessed conduit box This 2 zone programmer is designed to provide ON/OFF control for one hot water and one heating zone, with the value added application of in built frost protection. Important: Keep this document 1 3 4 5 6 2 Type EN60730 1C IP20 EN60529 50 °C 0 122 °F 32 5-95%RH 160.5 100 CAUTION! Installation and connection should only be carried out by a qualifed person and in accordance with national wiring regulations.  Before commencing any work on the electrical connections, you must frst disconnect the programmer from the mains. None of the 230V connections must be live until the installation has been completed and the housing is closed. Only qualifed electricians or authorised service staf are permitted to open the programmer. Disconnect from mains supply in the event of any damage to any buttons.  There are parts that carry mains voltage behind the cover. The programmer must not be left unsupervised when open. (Prevent non specialists and especially children from gaining access to it.)  If the programmer is used in a way not specifed by the manufacturer, its safety may be impaired.  Prior to setting the timeswitch, it is neccessary to complete all required settings described in this section.  Never remove this product from the electrical baseplate. Do not use sharp tools to push any button.

CAUTION! Before commencing, disconnect the device from the mains. There are parts that carry mains voltage behind the cover. Never leave unsupervised when it is open. (Prevent non specialists and especially children from gaining access to it.) Never remove this product from the electrical baseplate. Disconnect from mains supply in the event of any damage to any buttons. Do not use sharp tools to push any button. R27-HW - 2 Zone Programmer Operating Instructions Page 1 of 2 Press the or buttons to adjust the P1 ON time. Press the or buttons to adjust the P1 OFF time. Repeat this process to adjust the ON & OFF times for P2 & P3. Press and repeat the above process to adjust for HEATING. When completed, move the selector switch to the RUN position. 1. Factory default settings 6. Adjusting the program settings 2. Factory program settings Program: 5/2D Backlight: On Keypad: Unlocked Frost Protection: Of Lower the cover on the front of the unit. Move the selector switch to the PROG SET position. You can now program the HOT WATER. 3. Resetting the programmer Press Press This 2 zone programmer is designed to provide ON/OFF control for both Hot Water and Heating, with the value added application of in built frost protection. It is necessary to press the RESET button prior to initial programming. This button is located behind the cover on the front of the unit. Lower the cover on the front of the unit. By pressing the button, you can change between AUTO / ALL DAY / ON / OFF for HOT WATER. Repeat this process for HEATING by pressing the button. 5. ON/OFF period selection There are 4 modes available on this programmer for users to choose for their individual application. SELECT SELECT SELECT Contents 1. Factory default settings 2. Factory program settings 3. Resetting the programmer 4. Setting the date and time 5. ON/OFF period selection 6. Adjusting the program settings 7. Copy function 8. Reviewing the program settings 9. Boost function 10. Advance function 11. Holiday mode 12. Backlight mode selection 13. Keypad lock and unlock 14. Frost protection function 15. Master reset 4. Setting the date and time Press Press Press Press Press Press Lower the cover on the front of the unit. Move the selector switch to the CLOCK SET position. Press the or buttons to select the day. Press the or buttons to select the month. Press the or buttons to select the year. Press the or buttons to select the hour. Press the or buttons to select the minute. Press the or buttons to select 5/2D, 7D or 24H The date, time and function are now set. Move the selector switch to the RUN position to run the program, or to the PROG SET position to change the program setting. RUN CLOCK SET PROG SET AUTO The programmer operates 3 ‘ON/OFF’ periods per day. ALL DAY The programmer operates 1’ON/OFF’ period per day. This operates from the frst ON time to the third OFF time. ON The programmer is permanently on. **ON** OFF The programmer is permanently of. **OFF** Copy function may only be used if the programmer is in the 7d mode. Lower the cover on the front of the programmer. Move the selector switch to the PROG SET position. Set the ON & OFF times for the day of the week you wish to copy from. Press the button for 2 secs. The next day of the week will begin to fash. Press the button to copy the ON & OFF to this day. Press the button to skip a day. ON & OFF times can be copied to multiple days by using the button. Press the button when copying has been completed. When completed, move the selector switch to the RUN position. RUN CLOCK SET PROG SET Holiday COPY 7. Copy function EPH Controls Ireland [email protected] www.ephcontrols.com EPH Controls UK [email protected] www.ephcontrols.co.uk 20180621_R27-HW_OpIns_JW Important: Keep this document RUN CLOCK SET PROG SET Mon-Fri Sat-Sun 5/2D P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30 7:30 10:00 12:00 12:00 17:00 23:00 All 7 days 7D P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30 Everyday 24H P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30

CAUTION! Before commencing, disconnect the device from the mains. There are parts that carry mains voltage behind the cover. Never leave unsupervised when it is open. (Prevent non specialists and especially children from gaining access to it.) Never remove this product from the electrical baseplate. Disconnect from mains supply in the event of any damage to any buttons. Do not use sharp tools to push any button. R27-HW - 2 Zone Programmer Operating Instructions Page 1 of 2 Press the or buttons to adjust the P1 ON time. Press the or buttons to adjust the P1 OFF time. Repeat this process to adjust the ON & OFF times for P2 & P3. Press and repeat the above process to adjust for HEATING. When completed, move the selector switch to the RUN position. 1. Factory default settings 6. Adjusting the program settings 2. Factory program settings Program: 5/2D Backlight: On Keypad: Unlocked Frost Protection: Of Lower the cover on the front of the unit. Move the selector switch to the PROG SET position. You can now program the HOT WATER. 3. Resetting the programmer Press Press This 2 zone programmer is designed to provide ON/OFF control for both Hot Water and Heating, with the value added application of in built frost protection. It is necessary to press the RESET button prior to initial programming. This button is located behind the cover on the front of the unit. Lower the cover on the front of the unit. By pressing the button, you can change between AUTO / ALL DAY / ON / OFF for HOT WATER. Repeat this process for HEATING by pressing the button. 5. ON/OFF period selection There are 4 modes available on this programmer for users to choose for their individual application. SELECT SELECT SELECT Contents 1. Factory default settings 2. Factory program settings 3. Resetting the programmer 4. Setting the date and time 5. ON/OFF period selection 6. Adjusting the program settings 7. Copy function 8. Reviewing the program settings 9. Boost function 10. Advance function 11. Holiday mode 12. Backlight mode selection 13. Keypad lock and unlock 14. Frost protection function 15. Master reset 4. Setting the date and time Press Press Press Press Press Press Lower the cover on the front of the unit. Move the selector switch to the CLOCK SET position. Press the or buttons to select the day. Press the or buttons to select the month. Press the or buttons to select the year. Press the or buttons to select the hour. Press the or buttons to select the minute. Press the or buttons to select 5/2D, 7D or 24H The date, time and function are now set. Move the selector switch to the RUN position to run the program, or to the PROG SET position to change the program setting. RUN CLOCK SET PROG SET AUTO The programmer operates 3 ‘ON/OFF’ periods per day. ALL DAY The programmer operates 1’ON/OFF’ period per day. This operates from the frst ON time to the third OFF time. ON The programmer is permanently on. **ON** OFF The programmer is permanently of. **OFF** Copy function may only be used if the programmer is in the 7d mode. Lower the cover on the front of the programmer. Move the selector switch to the PROG SET position. Set the ON & OFF times for the day of the week you wish to copy from. Press the button for 2 secs. The next day of the week will begin to fash. Press the button to copy the ON & OFF to this day. Press the button to skip a day. ON & OFF times can be copied to multiple days by using the button. Press the button when copying has been completed. When completed, move the selector switch to the RUN position. RUN CLOCK SET PROG SET Holiday COPY 7. Copy function 20170314_AW1077_R27-HW_OpIns_JW Important: Keep this document RUN CLOCK SET PROG SET Mon-Fri Sat-Sun 5/2D P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30 7:30 10:00 12:00 12:00 17:00 23:00 All 7 days 7D P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30 Everyday 24H P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF 6:30 8:30 12:00 12:00 16:30 22:30 EPH Controls Ireland Sitecast Industrial Estate, Pouladuf, Cork, T12 W665, Ireland [email protected] www.ephcontrols.com EPH Controls UK Unit E4, Welland Business Park, Valley Way, Market Harborough, Leicestershire, LE16 7PS, United Kingdom [email protected] www.ephcontrols.co.uk