Escali RL136 Manuals

OWNER’S MANUAL WWW.ESCALI.COM PORTION CONTROL SCALE R-SERIES MODEL # RL136 Thank you for your purchase! Please read the owner’s manual carefully to ensure proper function of your scale. 2 BASIC SETUP 1. Plug in the 9-volt wall adapter (included.) 2. Remove the clear plastic film from the Display Unit and the white plastic film from the stainless steel platform. PARTS LABELED * Denotes parts that come attached to the scale. Reference the drawings below during assembly. ASSEMBLYING THE DISPLAY CONFIGURATIONS A) Attached Display Configuration • The scale comes assembled in the Attached Display Configuration. • Follow steps 1-9 until the desired display configuration is assembled. 7 mm Screw 14 mm Screw 13 mm Screw Wall Mount Screw Drywall Anchor (left) Grey Bracket Metal Display Mount (right) Grey Bracket Spacing Washwer x2 x4 x2 x2 x2 x2 Attention: Parts not drawn to scale. Display Unit Scale Coiled Extension Cord Vertical Arm Display Cord * * * * * * * * A A) B) C) D) Attached Display Detached Tabletop Display Wall Mount Display Standing Mount Display 3 B) Detached Tabletop Display Configuration 1. Unscrew the two 13 mm Screws connecting the Display Unit to the Metal Display Mount, and save the two 13 mm Screws for step 8. Skip steps 2-3 for D) Standing Mount Display Configuration. 2. Unscrew the two 14 mm Screws that attach the Metal Display Mount to the underside of the scale. Spin the Metal Display Mount around so it no longer protrudes from the underside of the scale and reattach it with the Spacing Washers remaining inbetween. C) Wall Mounted Display Configuration 3. Add the Coiled Extension Cord to the Display Cord. 4. Remove the four 7 mm Screws from the two Grey Brackets located underneath the Display Unit, and save the 7 mm Screws for step 6. 5. Tuck the Display Cord all the way into Notch A at the top of the Vertical Arm, and slide the Vertical Arm into the Display Unit. It will be a tight fit. Reference the Vertical Arm drawing on page 2 to locate Notch A. 6. Use the four 7 mm Screws saved from step 4 to fasten the Vertical Arm to the Display Unit. Skip step 7 for D) Standing Mount Display Configuration. 7. Attach the two Wall Mount Screws to a wall vertically spaced and 4 cm apart on center. Hang the Vertical Arm and Display Unit on the two Wall Mount Screws. Pre-drill 1/4 inch diameter holes for the Drywall Anchors when mounting onto a drywall surface, or 3/32 inch diameter holes for the Wall Mount Screws alone. D) Standing Mount Display Configuration 8. Use the two 13 mm Screws saved from step 1 to attach the Metal Display Mount inbetween the rubber feet of the Vertical Arm. The Metal Display Mount should protrude in the direction the Display Unit is facing. 9. Plug the Display Cord into the scale. Attention! Save all unused parts for future reconfigurations. PRODUCT SUPPORT 24/7 Online community support: http://escali.zendesk.com Email support: [email protected] Phone support: 1-800-467-6408 4 Product Guide WEIGHT MEASUREMENTS 1. Press ON/OFF/TARE to turn the scale on. 2. Press MODE to change units: Pounds, pounds+ounces, ounces, fluid ounces, kilograms and milliliters. See pages 4-5 for details on Counting Mode (5, 10, 25, 50 piece sample sizes) and Percentage Weighing. 3. Place an item on the scale in the center of the platform. TARE (ADD & WEIGH) To ignore the weight of a container: 1. Place a container on the platform before turning the scale on. -OR- 1. Turn on the scale, add the container and press TARE or ZERO. 2. Add items into the container to be weighed. Find the individual weight of multiple items in one container: 1. Press TARE or ZERO to reset the scale back to zero weight. 2. Add additional items to be weighed. 3. Repeat steps 1-2 for each additional item. Reset the scale back to zero weight: 1. If nothing is on the scale and it does not read zero weight, press TARE or ZERO to reset the scale back to zero weight. Attention! The scale will tare any amount of weight. Once the total weight actually on the scale reaches the maximum capacity of 13 pounds (6kg.) the overload warning code (E) will display. TARE FOOT PEDAL (OPTIONAL ACCESSORY) An optional Tare Foot Pedal is avaliable, which allows hands free tare functionality. For more information visit: www.escali.com COUNTING MODE 1. Press MODE to select a sample quantity (5, 10, 25, 50 pcs.) 2. Place a sample of the items to be counted on the scale . 3. Press ON/OFF/TARE to confirm. 4. Place your total quantity on the platform. Display will show the total quantity.