ExSilent QLeaf Lite Manuals

Placing the battery and switching the module on First remove the sticker from the battery. Place the battery in the module with the (+) sign (this is the fl at side of the battery where the sticker was) at the same side as the (+) sign on the module. The module is set to program 1. 1 Placing the module in the soft tip (step 1) Start with a ‘medium’ soft tip*. Hold the soft tip with the pull cord pointed upwards. Place the module in the soft tip with the arrow facing towards you. 2 Placing the module in the soft tip (step 2) Push the module gradually into the soft tip. Insert the module all the way into the soft tip. The device is now ready for use. Placing the device in the ear There is no diff erence between the left and the right device, therefor it doesn’t matter which device you insert in your ear. Place the device in the ear with the pull cord (long part of the soft tip) at the side of the ‘tragus’ (see image). Push the device gently with an up and down movement as far in the ear as possible. The ear canal goes a little upwards, so it’s best to push the device a bit upwards and inwards until it cannot go further. You can insert the device deep into the ear without damaging the eardrum. If you feel the device is not properly positioned in your ear, the following tips may help (this instruction is written for the left ear): • Move you right arm over your head • With your right hand, grab the upper part of your left ear • Pull the ear up a little • With your left hand, you push the device a little further into the left ear, with an up and down movement (as your ear canal goes up a little). Do this exactly the other way around for the device in your right ear. Switching programs with the AirTAP™ functionality Switch programs with the AirTAP™ functionality by softly tapping the ear twice (with approximately half a second in between the two taps). It is important that the ear is closed off with the fi ngers, so that the device properly notes the diff erence in air pressure. The number of beeps indicates which program is in use *. Using the telephone Switch the device to program 3 . Hold the phone against your ear at the front, but keep the phone a little further away (about 45°) from your ear at the back. Cutting the soft tip When the device is placed properly in the ear, a small part of the pull cord will usually be visible. You are able to cut a few ribs off the pull cord with a pair of scissors. Always leave a minimum of 2 ribs, for easy removal of the soft tip from the ear. 4 3 6 7 5 Contents of the package 1 Module Qleaf Lite 2 Introduction set of soft tips made of hypoallergenic material (S open en closed version, M and L closed version) 3 Battery (type 10) 4 Battery ejection tool 5 Box 6 Quick start guide 1 2 3 5 4 6 ‘tragus’  * Check ‘troubleshooting’ at the backside of the quick start guide if the soft tip doesn’t fi t correctly. * Check ‘Use of diff erent listening programs’ on the backside of the quick start guide. S M L 45° • In order to get accustomed to the Qleaf Lite we advise a continuous wearing period of one hour, in case of fi rst use. Subsequently, increase the wearing time one hour each day. The eventual wearing time per day will vary due to situation(s) in which you need the device. It’s important to increase usage time slowly due to the possibility of hearing certain sounds such as the rustling of paper, fl ushing the toilet etc. After 10 to 14 days, your brain will be accustomed to the new sounds; they will become less conspicuous. You will also be less aware you are using a personal sound amplifi er. • Clean the device daily after use. Check ‘Cleaning the Qleaf Lite’ at the backside of the quick start guide. • If the battery is almost dead, the device will indicate this every 10 minutes with a series of double beeps. Replace the battery in a timely manner and make sure you always have an accessible spare battery. Tips for optimal use Removing the device from the soft tip Pull the pull cord down to release the module. Take the module out of the soft tip. Removing the device from the ear Hold the pull cord between your thumb and index fi nger and pull the device gradually from the ear. Turning the device off or replacing a battery Switch the device off by pushing the battery out through the small round opening, at the long (under) side of the de- vice, with the supplied battery eject tool. To insert a (new) battery, check step 1 placing the battery.

Placing the battery and switching the module on First remove the sticker from the battery. Place the battery in the module with the (+) sign (this is the flat side of the battery where the sticker was) at the same side as the (+) sign on the module. The module is set to program 1. 1 Placing the module in the soft tip (step 1) Start with a ‘medium’ soft tip*. Hold the soft tip with the pull cord pointed upwards. Place the module in the soft tip with the arrow facing towards you. 2 Placing the module in the soft tip (step 2) Push the module gradually into the soft tip. Insert the module all the way into the soft tip. The device is now ready for use. Placing the device in the ear A Place the device in the ear with the ‘pull cord’ (long part of the soft tip) at the side of the ‘tragus’. B Move you arm over your head. Grab the upper part of your ear. Pull the ear up a little as this will straighten the ear canal, which makes it easier to insert the device further. C While pulling the ear up, push the device gently with an up and down movement as far in the ear as possible. Switching programs with the AirTAP™ functionality Switch programs with the AirTAP™ functionality by softly tapping the ear twice (with approximately half a second in between the two taps). It is important that the ear is closed off with the fingers, so that the device properly notes the difference in air pressure. The number of beeps indicates which program is in use *. Using the telephone Switch the device to program 3 . Hold the phone against your ear at the front, but keep the phone a little further away (about 45°) from your ear at the back. Cutting the soft tip When the device is placed properly in the ear, a small part of the pull cord will usually be visible. You are able to cut a few ribs off the pull cord with a pair of scissors. Always leave a minimum of 2 ribs, for easy removal of the soft tip from the ear. 4 3 6 7 5 Contents of the package 1 Module Qleaf Lite 2 Introduction set of soft tips made of hypoallergenic material (S open en closed version, M and L closed version) 3 Battery (type 10) 4 Battery ejection tool 5 Box 6 Quick start guide 1 2 3 5 4 6  * Check ‘troubleshooting’ at the backside of the quick start guide if the soft tip doesn’t fit correctly. * Check ‘Use of different listening programs’ on the backside of the quick start guide. S M L 45° • In order to get accustomed to the Qleaf Lite we advise a continuous wearing period of one hour, in case of first use. Subsequently, increase the wearing time one hour each day. The eventual wearing time per day will vary due to situation(s) in which you need the device. It’s important to increase usage time slowly due to the possibility of hearing certain sounds such as the rustling of paper, flushing the toilet etc. After 10 to 14 days, your brain will be accustomed to the new sounds; they will become less conspicuous. You will also be less aware you are using a personal sound amplifier. • Clean the device daily after use. Check ‘Cleaning the Qleaf Lite’ at the backside of the quick start guide. • If the battery is almost dead, the device will indicate this every 10 minutes with a series of double beeps. Replace the battery in a timely manner and make sure you always have an accessible spare battery. Tips for optimal use Removing the device from the soft tip Pull the pull cord down to release the module. Take the module out of the soft tip. Removing the device from the ear Hold the pull cord between your thumb and index finger and pull the device gradually from the ear. Turning the device off or replacing a battery Switch the device off by pushing the battery out through the small round opening, at the long (under) side of the device, with the supplied battery eject tool. To insert a (new) battery, check step 1 placing the battery. A B C ‘tragus’ ‘pull cord’