Extron electronics TLP Pro 1225TG Manuals

1 IMPORTANT: Go to www.extron.com for the complete user guide and installation instructions before connecting the product to the power source. TLP Pro 1225TG and TLP Pro 1525TG • Setup Guide Overview The Extron TLP Pro 1225TG and TLP Pro 1525TG are table-top touchpanels with high resolution capacitive, edge-to-edge glass touchscreens. The TLP Pro 1225TG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1525TG has a 15.6 inch screen with a 1366x768 resolution. Both touchpanels are ideal for any AV applications requiring large touchpanels with flexible mounting options and fully customizable interfaces. This guide provides instructions for experienced installers to mount and install these touchpanels. For more complete details, see the TLP Pro 1225 and TLP Pro 1525 Series User Guide at www.extron.com. Setup Overview and Checklist Get Ready Download and install the latest version of the following software: z GUI Designer — For designing layouts for Extron TouchLink® Pro touchpanels and third party touch interfaces. z Global Configurator® Plus and Professional — For setting up and configuring the control processor and touchpanel. z Toolbelt — For device discovery, device information, firmware updates, and configuration of network settings, system utilities, and user management for TouchLink Pro devices. z Global Scripter® — Provides an integrated development environment for Extron control systems programming. NOTE: All four software programs are available from www.extron.com. Obtain the following network information from your network administrator: DHCP status (on or off). If DHCP is off, you also require: IP address Subnet mask Gateway Username — This can be either admin or user. Passwords — The factory configured passwords for all accounts on this device have been set to the device serial number. Passwords can be changed during configuration. Passwords are case sensitive. NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron (for either admin or user). Make a note of the touchpanel MAC address. Mount and Cable All Devices ATTENTION: • Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply section of the TLP Pro 1225 and TLP Pro 1525 Series User Guide or the IPL Pro User Guide. • Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section « sources d’alimentation » du TLP Pro 1225 and TLP Pro 1525 Series User Guide ou du IPL Pro User Guide. Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on page 2). Connect cables to the touchpanels (see Rear Panel Features on page 4). An Extron IP Link® control processor must be connected to the same Ethernet subnetwork as the touchpanel. Set up the Touchpanels for Network Communication Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork. Use the Setup Menu (see page 5) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, gateway, and related settings for the touchpanel. Configure the Touchpanels Create a graphical user interface with GUI Designer (see GUI Designer Help File for step-by-step instructions). Associate functions with the graphical user interface features by configuring (see the Global Configurator Help File) or programming (see the Global Scripter Help File) the system. Global Scripter provides an Extron-exclusive Python library (ControlScript®) and Global Scripter modules to get you started. 2 TLP Pro 1225TG and TLP Pro 1525TG • Setup Guide Mounting A range of optional mounting kits are available for both models. The kits must be purchased separately. Follow the installation instructions provided with the kit. Removing the back and base covers Some of these procedures require the back and base covers to be removed. You must remove the back cover before you can remove the base cover. 1. Use the provided Extron removal tool. There is one notch on each side of the back cover (figure 1, 1). Insert the tool into the notch to release the catch. 2. Use the removal tool to remove the base cover. There are two notches at the back of the base (2). 2. Drill two pilot holes into the desktop. 3. Remove the base cover (see Removing the back and base covers, above). 4. Insert two #10 flat-head wood screws (not provided) through the touchpanel and align them with the two pilot holes. 5. Secure the touchpanel to the tabletop. 6. Replace the base cover. Kensington® Security Lock For added security, attach a Kensington Security Lock (not provided) to the metal-reinforced Kensington Security Slot on the rear edge of the base (see figure 3, 1). The figure shows the rear edge of the TLP Pro 1525TG base, but the base of the TLP Pro 1225TG is very similar. Follow the instructions that are provided by the manufacturer to install the lock. Desktop Mounting The TLP Pro 1225TG and TLP Pro 1525TG come assembled with stands that allow the units to be placed on any suitable flat surface (for example a desk, table, or lectern). Fixed Mounting Figure 2 shows the base of the TLP Pro 1225TG, with the cover removed to indicate the position of the mounting holes (see figure 2, 1). The base of the TLP Pro 1525TG is similar and the spacing of the mounting holes is identical. 1. Mark the location for two holes, 4.96 inches (126 mm) apart. This measurement is the same for both models. 1 SMA-1 Swivel Mount Adapter To swivel either device up to 180° in either direction, use the optional Extron SMA-1 swivel mount adapter, to permanently mount the touchpanels. 1. Remove the back cover and base cover (see Removing the back and base covers, above). 2. Attach the conduit, insulation disk, and swivel disk and configure the set screws to allow for the degree of swivel that is required (see the SMA-1 Swivel Mount Adapter Kit User Guide, available at www.extron.com). Place the mounting hole in the base over the conduit of the SMA-1. 3. Secure the unit with the backing plate and locking nut as described in the SMA-1 Swivel Mount Adapter Kit User Guide. VESA Mounting Use a third-party D-type VESA mounting kit with the 100 mm x 100 mm mounting pattern. 1. Remove the back cover. 2. Remove the four screws holding the touchpanel to the base. There are two screws in each base attachment hinge. 3. Follow the instructions provided with the VESA mounting kit. 1 1 2 2 Figure 1. Remove the Back and Base Covers Figure 2. Mounting Holes in TLP Pro 1225TG Base Figure 3. Slot for Kensington Security Lock 3 Product Category Front Panel Features Figure 4 shows the TLP Pro 1225TG front panel diagram. The features of the TLP Pro 1525TG are very similar. A B C D D E Figure 4. TLP Pro 1225TG Front Panel A Ambient light sensor — Monitors ambient light level and adjusts screen brightness. B Status light — Can be programmed to provide system feedback. The LED light bar is located above the screen. C Capacitive touch screen — Provides simple control of AV systems: z The TLP Pro 1225TG has a 12.1 inch screen with a 1280x800 resolution. z The TLP Pro 1525TG has a 15.6 inch screen with 1366x768 resolution. D Speakers — Provide stereo audio for video preview and audible feedback from button presses. They are located below the screen, one on each side of the panel. E Motion sensor — Detects motion between three to five feet from the touchpanel, and at least 15° from the center axis. z If the Sleep Timer has been set (see Setup Menu on page 6), and no motion has been detected for a user-defined period of time, the touchpanel enters sleep mode. z If Wake on Motion has been set (see Setup Menu), and motion is detected by the sensor while the screen is in sleep mode, the screen display is restored and active. 4 TLP Pro 1225TG and TLP Pro 1525TG • Setup Guide Rear Panel Features Figure 5 shows the TLP Pro 1225TG rear panel diagram (with the base and back cover removed). The features of the TLP Pro 1525TG are very similar. XTP / PoE / LAN HDMI IN 1 2 12VDC 3A RESET MENU Marking B C D E F G H I J A A Rear status light E HDMI input I Menu button (see page 5) B Vesa mounting holes F XTP/LAN/PoE input J Reset button (see page 5) C Power supply input G Audio output (see page 5) D USB connectors H Reset LED (see page 5) Figure 5. TLP Pro 1225TG Rear Panel (with base and back cover removed) A Rear status light — An LED light bar that can be programmed to provide system feedback. B VESA mounting holes (4) — For use with D-type VESA mounting kits with the 100 x 100 mm mounting pattern. C Power supply input — Connect a 12 VDC, 3.0 A Limited Power Source (LPS) power supply to this DC plug connector. ATTENTION: • The touchpanels can use a 12 VDC desktop power supply or Power over Ethernet. Do not connect either power supply before reading the Attention in the Power section of the TLP Pro 1225 and TLP Pro 1525 Series User Guide. • Les écrans tactiles peuvent utiliser une source d’alimentation externe 12 Vcc ou l’alimentation POE via Ethernet. Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section « Power Supply » du TLP Pro 1225 and TLP Pro 1525 Series User Guide. D USB connectors (2) — For peripheral controls. E HDMI input — For alternative video input. F XTP/LAN/PoE input z XTP input — Connect the touchpanel to the XTP source using a twisted pair cable, terminated with an RJ‑45 connector. For complete information about which cables to use, see the user guide for your XTP product. z LAN input — Connect the touchpanel to the LAN using a twisted pair cable, terminated with an RJ‑45 connector. z PoE input — The connector can be used with a PoE power injector (see Connecting Power on page 5). NOTE: Some XTP models are able to remotely power these touchpanels but not all have that capability. Go to the Extron website and check the product page for your XTP model to ensure it can power your touchpanel. An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.

1 IMPORTANT: Go to www.extron.com for the complete user guide and installation instructions before connecting the product to the power source. TLP Pro 1225TG, 1525TG, and 1725TG • Setup Guide Overview The Extron® TLP Pro 1225TG, TLP Pro 1525TG, and TLP Pro 1725TG are table-top touchpanels with high resolution capacitive, edge-to-edge glass touchscreens. The TLP Pro 1225TG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1525TG has a 15.6 inch screen with a 1366x768 resolution. The TLP Pro 1725TG has a 17.3 inch screen with a 1920x1080 resolution. All three touchpanels are ideal for any AV applications requiring large touchpanels with flexible mounting options and fully customizable interfaces. This guide provides instructions for experienced installers to mount and install these touchpanels. For more complete details, see the TLP Pro 1225, 1525, and 1725 Series User Guide at www.extron.com. Setup Overview and Checklist Get Ready Download and install the latest version of the following software: z GUI Designer — For designing layouts for Extron TouchLink® Pro touchpanels and third party touch interfaces z Global Configurator® Plus and Professional — For setting up and configuring the control processor and touchpanel z Global Scripter® — Provides an integrated development environment for Extron control systems programming. Global Scripter provides an Extron-exclusive Python™ library (ControlScript®) and Global Scripter modules to get you started. z Toolbelt — For device discovery, device information, firmware updates, and configuration of network settings, system utilities, and user management for TouchLink Pro devices. NOTE: All four software programs are available from www.extron.com. Obtain the following network information from your network administrator: DHCP status (on or off). If DHCP is off, you also require: IP address Subnet mask Gateway Username — This can be either admin or user. Passwords — The factory configured passwords for all accounts on this device have been set to the device serial number. Passwords can be changed during configuration. Passwords are case sensitive. NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron (for either admin or user). Make a note of the touchpanel MAC address. Mount and Cable All Devices ATTENTION: • Do not power on the touchpanels until you have read the Attention in the Power Supply section of the TLP Pro 1225, 1525, and 1725 Series User Guide. • Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section « sources d’alimentation » du TLP Pro 1225, 1525, and 1725 Series User Guide. Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on page 2). Connect cables to the touchpanels (see Rear Panel Features on page 4). Connect the touchpanel to a power source. These models can be powered by PoE or by a 12VDC power supply. The TLP Pro 1725TG ships with the PI 140 power injector. A power injector or 12 VDC power supply must be purchased separately for the 12” and 15” models. An Extron IP Link® control processor must be connected to the same Ethernet subnetwork as the touchpanel. Set up the Touchpanels for Network Communication Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork. Use the Setup Menu (see page 6) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, gateway, and related settings for the touchpanel. Configure the Touchpanels Create a graphical user interface with GUI Designer (see GUI Designer Help File for step-by-step instructions). Associate functions with the graphical user interface features with Global Configurator or Global Scripter. 2 TLP Pro 1225TG, 1525TG, and 1725TG • Setup Guide Mounting A range of optional mounting kits are available for these models. The kits must be purchased separately. Follow the installation instructions provided with the kit. Removing the back and base covers Some of these procedures require the back and base covers to be removed. You must remove the back cover before you can remove the base cover. 1. Use the provided Extron removal tool. There is one notch on each side of the back cover (figure 1, 1). Insert the tool into the notch to release the catch. 2. Use the removal tool to remove the base cover. There are two notches at the back of the base (2). 2. Drill two pilot holes into the desktop. 3. Remove the base cover (see Removing the back and base covers, above). 4. Insert two #10 flat-head wood screws (not provided) through the touchpanel and align them with the two pilot holes. 5. Secure the touchpanel to the tabletop. 6. Replace the base cover. Kensington® Security Lock For added security, attach a Kensington Security Lock (not provided) to the metal-reinforced Kensington Security Slot on the rear edge of the base (see figure 3, 1). The figure shows the rear edge of the TLP Pro 1525TG base, but the base of the TLP Pro 1225TG and TLP Pro 1725TG are very similar. Follow the instructions that are provided by the manufacturer to install the lock. Desktop Mounting These touchpanels come assembled with stands that allow them to be placed on any suitable flat surface (for example a desk, table, or lectern). Fixed Mounting Figure 2 shows the base of the TLP Pro 1225TG, with the cover removed to indicate the position of the mounting holes (1). The base of the TLP Pro 1525TG and TLP Pro 1725TG are similar and the spacing of the mounting holes is identical. 1. Mark the location for two holes, 4.96 inches (126 mm) apart. This measurement is the same for all three models. 1 SMA-1 Swivel Mount Adapter To swivel either device up to 180° in either direction, use the optional Extron SMA-1 swivel mount adapter, to permanently mount the touchpanels. 1. Remove the back cover and base cover (see Removing the back and base covers, above). 2. Attach the conduit, insulation disk, and swivel disk and configure the set screws to allow for the degree of swivel that is required (see the SMA-1 Swivel Mount Adapter Kit User Guide, available at www.extron.com). Place the mounting hole in the base over the conduit of the SMA-1. 3. Secure the unit with the backing plate and locking nut as described in the SMA-1 Swivel Mount Adapter Kit User Guide. VESA Mounting Use a third-party D-type VESA mounting kit with the 100 mm x 100 mm mounting pattern. 1. Remove the back cover. 2. Remove the four screws holding the touchpanel to the base. There are two screws in each base attachment hinge. 3. Follow the instructions provided with the VESA mounting kit. 1 1 2 2 Figure 1. Remove the Back and Base Covers Figure 2. Mounting Holes in TLP Pro 1225TG Base Figure 3. Slot for Kensington Security Lock 3 Product Category Front Panel Features Figure 4 shows the TLP Pro 1225TG front panel diagram. The features of the TLP Pro 1525TG and TLP Pro 1725TG are very similar. A B C D D E Figure 4. TLP Pro 1225TG Front Panel A Ambient light sensor — Monitors ambient light level and adjusts screen brightness. B Status light — Can be programmed to provide system feedback. The LED light bar is located above the screen. C Capacitive touch screen — Provides simple control of AV systems: z The TLP Pro 1225TG has a 12.1 inch screen with a 1280x800 resolution. z The TLP Pro 1525TG has a 15.6 inch screen with 1366x768 resolution. z The TLP Pro 1725TG has a 17.3 inch screen with a 1920x1080 resolution. D Speakers — Provide stereo audio for video preview and audible feedback from button presses. They are located below the screen, one on each side of the panel. E Motion sensor — Detects motion between three to five feet from the touchpanel, and at least 15° from the center axis. z If the Sleep Timer has been set (see Setup Menu on page 6), and no motion has been detected for a user-defined period of time, the touchpanel enters sleep mode. z If Wake on Motion has been set (see Setup Menu), and motion is detected by the sensor while the screen is in sleep mode, the screen display is restored and active.

68-3474-01 Rev. A 09 20 TLP Pro 1225, 1525, and 1725 Series User Guide TouchLink Pro Touchpanels TouchLink Pro Touchpanel Control Systems Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide, part number 68-290-01, on the Extron website, www.extron.com. Sicherheitsanweisungen • Deutsch WARUNG: Dieses Symbol auf demProdukt soll den Benutzer darauf aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und die einen elektrischen Schlag verursachen können. VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben. Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung, EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer 68-290-01) auf der Extron-Website, www.extron.com. Instrucciones de seguridad • Español ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto, avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del producto, lo que puede representar un riesgo de descarga eléctrica. ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa al usuario de la presencia de importantes instrucciones de uso y mantenimiento estas estan incluidas en la documentación proporcionada con el equipo. Para obtener información sobre directrices de seguridad, cumplimiento de normativas, compatibilidad electromagnética, accesibilidad y temas relacionados, consulte la Guía de cumplimiento de normativas y seguridad de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com. Instructions de sécurité • Français AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le produit, signale à l’utilisateur la présence à l’intérieur du boîtier du produit d’une tension électrique dangereuse susceptible de provoquer un choc électrique. ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit, signale à l’utilisateur des instructions d’utilisation ou de maintenance importantes qui se trouvent dans la documentation fournie avec l’équipement. Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les informations de sécurité et de conformité Extron, réf. 68‑290-01, sur le site Extron, www.extron.com. Safety Instructions Istruzioni di sicurezza • Italiano AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad avvertire l’utente della presenza di tensione non isolata pericolosa all’interno del contenitore del prodotto che può costituire un rischio di scosse elettriche. ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire l’utente della presenza di importanti istruzioni di funzionamento e manutenzione nella documentazione fornita con l’apparecchio. Per informazioni su parametri di sicurezza, conformità alle normative, compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo 68‑290‑01, sul sito web di Extron, www.extron.com. Instrukcje bezpieczeństwa • Polska OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu poinformować użytkownika o obecności izolowanego i niebezpiecznego napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie porażenia prądem elektrycznym. UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji (obsługi) w literaturze, wyposażone w sprzęt. Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01, na stronie internetowej Extron, www.extron.com. Инструкция по технике безопасности • Русский ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан на продукте, предупреждает пользователя о наличии неизолированного опасного напряжения внутри корпуса продукта, которое может привести к поражению электрическим током. ВНИМАНИЕ: Данный символ, , если указан на продукте, предупреждает пользователя о наличии важных инструкций по эксплуатации и обслуживанию в руководстве, прилагаемом к данному оборудованию. Для получения информации о правилах техники безопасности, соблюдении нормативных требований, электромагнитной совместимости (ЭМП/ЭДС), возможности доступа и других вопросах см. руководство по безопасности и соблюдению нормативных требований Extron на сайте Extron: , www.extron.com, номер по каталогу - 68-290-01. 安全说明 • 简体中文 警告： 产品上的这个标志意在警告用户, 该产品机壳内有暴露的危险 电压，有触电危险。 注意： 产品上的这个标志意在提示用户, 设备随附的用户手册中有重 要的操作和维护(维修)说明。 关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍使 用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见 Extron 安全规范指南，产品编号 68-290-01。 Copyright © 2020 Extron. All rights reserved. Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks®, registered service marks(SM), and trademarks(™) are the property of RGB Systems, Inc. or Extron (see the current list of trademarks on the Terms of Use page at www.extron.com): Registered Trademarks (®) Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, eLink, Flat Field, FlexOS, Glitch Free, Global Configurator, Global Scripter, GlobalViewer, Hideaway, HyperLane, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NAV, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation, System INTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN‑Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTP Systems, and ZipClip. Registered Service Mark(SM) : S3 Service Support Solutions Trademarks (™) AAP, AFL (Accu-RATE Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D Ripple Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, SIS, Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy 안전 지침 • 한국어 경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는 접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을 경고합니다. 주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와 있는 주요 운영 및 유지보수(정비) 지침을 경고합니다. 안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오. 安全記事 • 繁體中文 警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在未隔離的危險 電壓，可能會導致觸電之風險。 注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有重要 的操作和維護（維修）説明。 有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資訊， 請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規遵守手 冊》，準則編號 68-290-01。