Fantom FANTOM PT302H Manuals

Owner’s Manual ROTARY TOOL KIT Model No. PT302H CAUTION: Before using this Rotary Tool, read this manual and follow all its Safety Rules and Operating Instructions.
Safety Instructions
Accessories
Assembly
Operation
Maintenance FANTOM, 178 West Service Road, Champlain, N.Y. 12919 Always have one hand firmly placed on the tool body while operating. Never operate the tool by holding only the tool handle. WARNING ! PRODUCT SPECIFICATIONS Rev. 06/03 SECTION PAGE SECTION PAGE Product Specifications …………………. 2 Carton Contents ………………………… 6, 7 Power Tool Safety ..…………………….. 3 Know Your Rotary Tool …………..…...... 8 Rotary Tool Safety .….................…... 4 Assembly & Operation …….…………… 9 – 17 Electrical Requirements & Safety …….. 5 Maintenance …………………………….. 17 Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
Lead from lead-based paints
Crystalline silica from bricks, cement and other masonry products
Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles. To avoid electrical hazards, fire hazards or damage to the rotary tool, use proper circuit protection. This rotary tool is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay fuse or curcuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way. Before using your rotary tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or damage to the rotary tool. TABLE OF CONTENTS WARNING ! 2 Motor Rating: 120V., 60Hz. 4.0 A. No Load Speed: 30,000 RPM Weight: 3.75 lbs. Warranty ….....................................……. 18 GENERAL SAFETY RULES Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. WORK AREA Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gasses or dust. Power tools create sparks which may ignite the dust or fumes. Keep bystanders, children and visitors away while operating the tool. Distractions can cause you to lose control. ELECTRICAL SAFETY Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized plug only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is increased risk of electric shock if your body is grounded. Don’t expose power tools to rain or wet conditions. Water entering the power tool will increase the risk of electric shock. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock. PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use the tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing and gloves away from moving parts. Loose clothing, jewelry or long hair can be caught in moving parts. Avoid accidental starting. Be sure switch is OFF before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch ON invites accidents. Remove adjusting keys or wrenches before turning the tool ON. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat or hearing protection must be used for appropriate conditions. TOOL USE AND CARE Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use the tool if the switch does not turn it ON or OFF. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source before making any adjustments, changing accessories or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. WARNING ! SAVE THESE INSTRUCTIONS FOR REFERENCE 3 POWER TOOL SAFETY