FeiYu Tech FY-G4 Manuals

FEIYU-EN-3 FY G4 is suitable for GoPro 4/GroPro 3+/GroPro 3, also can be compatible with GoPro LCD backpack and the cameras with the same size. EN Function Interface Function Button Video Input And Camera Charging Interface Power Switch Pitch Axis Roll Axis Indicator Heading Axis M2 Knurled Thumb Screw If the indicator light flashes red, the Gimbal will not work correctly due to an error. Please install the suitable camera first before power on the Gimbal. Please upgrade the firmware to V1.13 or above version. Attention ! 1 Beginner Guide 2 Product Appearance Instructions 4 Standard And Optional Accessories 6 6 Operation Instructions 3 Special Working Condition (Inversion Mode) When in any working mode, press the function button for three times in succession, the Gimbal will enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset the Gimbal back to the original state. Manual Pulling Locking The pitching can be adjusted 8 seconds after the Gimbal has been started. Within the Heading Follow and Heading Lock Mode the pitching can be adjusted to the desired angle manually, wait in this position up to 0.5 second until the current angle is adjusted. Standby Mode Press the function button for 3 seconds, then the motor will stop working and the LED of the function button will light constantly. This indicates that the Gimbal is in the standby mode. Single press the function button the Gimbal will be awakened immediately. Level Calibration The pitch and roll angle can be adjusted to level by G4 Remote Control without connect to the computer. Details of the operation please refer to chapter Heading Follow Speed Mode Configuration The follow speed of the heading can be configurate by G4 Remote Control without connect to the computer. Details of the operation please refer to chapter Reset Four press the function button in succession within any working mode, the gimbal will reset to the original state. If any comments or suggestions please do not hesitate to e-mail us directly : [email protected] Please choose one way to install the GoPro camera Installation Method L R Insert The Batteries Remove the power switch cap, insert two 18350 batteries into the handle. Install The Camera Install the GoPro camera by the special Thumb Screw. And make sure it is fixed well. Power On Confirm the camera is installed well,then press the power button to turn on the Gimbal. Mode Switching When the Gimbal is working, you can press the function button to switch among the three working modes and a special working condition. (Details of working modes please refer to the instructions of working modes) Function Button Working Mode Instructions Operation Double Press Single Press Long Press For 1 Second LED Status Single Flashes Double Flashes On Constantly Function Explanation Operation Again Function Of Operation Again Heading Follow Mode Heading And Pitch Follow Mode Three Press Three Press again Other operation is arbitrary Other operation is arbitrary Other operation is arbitrary Other operation is arbitrary Single press again Single Flashes Inversion Mode Exit inversion mode to original state Exit standby mode , and awaken immediately Heading Lock Mode Long Press For 3 Second On Constantly Standby Mode Four Press Single Flashes Reset Function Button Instructions Heading, Pitch and Roll are all locked to Use for switch the working mode and realize other functions The working mode and function can be identified by the LED status Heading Follow Mode Camera Pitch and Roll Angles remain Heading And Pitch Follow Mode Camera Roll Angle remains Heading Lock Mode Roll Pitch Heading constant, heading follows the handheld position. constant. Heading and Pitch follow the handheld position. point at one position. Indicator Explanation LED Status Explain Blue light flashes three times Full Power Blue light flashes twice Enough Power Blue light flashes once Low Power Blue light keeps flashing No Power Charger Input: DC 5V Output: DC 4.2V USB Cable USB Connector Extension Knurled Thumb Screw Name Remote Control Battery Extender Extension Bar Realize the heading & pitch angle adjustment, mode switching, level calibration and heading follow speed configuration from a distance. Extend the capacity space for battery to make the runtime longer. Spiral design of the extension bar can be perfect combination with G4 power switch； Extended length is optional, it will help to enjoy a different visual easily. Function Description Optional Accessories Correct Method for Using USB Data Cable Battery Charging: Connect The Computer: Put the Mini-USB terminal of the USB cable into the Mini-USB interface of the charger and the USB terminal to the power adapter which with the USB interface(Equipped by users) If needed connect to the EU connector (Equipped by users). Please remove the batteries first, then insert the Mini-USB terminal into the function interface on the Gimbal and the USB terminal to the USB connector. Afterwards connect the device with the computer to do firmware updates or parameter configuration. Further information can be found in the chapter of the Function Interface Instructions. Please refer to the method of proper usage mentioned below. Otherwise the device itself or other equipments can be damaged ! Standard Accessories Type: 18350 Rechargeable Battery USB Mini-USB Camera Charging Cable Video Output Cable

FEIYU-EN-3 FY-G4 is suitable for GoPro 4/GroPro 3+/GroPro 3, also can be compatible with GoPro LCD backpack and the cameras with the same size. EN Function Interface Function Button Video Input And Camera Charging Interface Power Switch Pitch Axis Roll Axis Indicator Heading Axis M2 Knurled Thumb Screw If the indicator light flashes red, the Gimbal will not work correctly due to an error. Please install the suitable camera first before power on the Gimbal. Please upgrade the firmware to V1.13 or above version. Attention ! 1 Beginner Guide 2 Product Appearance Instructions 4 Standard And Optional Accessories 6 6 Operation Instructions 3 Special Working Condition (Inversion Mode) When in any working mode, press the function button for three times in succession, the Gimbal enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset the Gimbal back to the original state. Manual Pulling Locking The pitching can be adjusted 8 seconds after the Gimbal has been started. Within the Heading Follow and Heading Lock Mode the pitching can be adjusted to the desired angle manually, wait in this position up to 0.5 second until the current angle is adjusted. Standby Mode Press the function button for 3 seconds, then the motor will stop working and the LED of the function button will light constantly. This indicates that the Gimbal is in the standby mode. Single press the function button the Gimbal will be awakened immediately. Level Calibration The pitch and roll angle can be adjusted to level by G4 Remote Control without connect to the computer. Details of the operation please refer to chapter Heading Follow Speed Mode Configuration The follow speed of the heading can be configurate by G4 Remote Control without connect to the computer. Details of the operation please refer to chapter Reset Four press the function button in succession within any working mode, the gimbal will reset to the original state. Charger Input: DC 5V Min 800mA Output: DC 4.2V Type: 16340/18350 Power Adapter European Standard Connector USB Cable USB Mini-USB USB Connector Extension Knurled Thumb Screw Correct Method For Using USB Data Cable Battery Charging: Connect The Computer: Put the Mini-USB terminal of the USB cable into the Mini-USB interface of the charger and the USB terminal to the power adapter, if needed connect to the EN Connector. Please remove the batteries first, then insert the Mini-USB terminal into the function interface on the Gimbal and the USB terminal to the USB connector. Afterwards connect the device with the computer to do firmware updates or parameter configuration. (Please connect the USB cable to the computer with the USB connector, otherwise the interface of the computer will be damaged ). Further information can be found in the chapter of the Function Interface Instructions. Name Remote Control Battery Extender Extension Bar Camera Charging Cable Video Output Cable Realize the heading & pitch angle adjustment, mode switching, level calibration and heading follow speed configuration from a distance. Extend the capacity space for battery to make the runtime longer. Spiral design of the extension bar can be perfect combination with G4 power switch； Extended length is optional, it will help to enjoy a different visual easily. The Gimbal can power supply for the Gopro camera. Through this cable the analog video signal of the Gopro camera will be send to the function interface on the Gimbal. Function Description Please refer to the method of proper usage mentioned below. Otherwise the device itself or other equipment can be damaged Optional Accessories ! Please connect the analoy monitor for displaying Standard Accessories Indicator Explanation LED Status Explain Blue light flashes three times Full Power Blue light flashes twice Enough Power Blue light flashes once Low Power Blue light keeps flashing No Power Type: 18350 Rechargeable Battery If any comments or suggestions please do not hesitate to e-mail us directly : [email protected] Please choose one way to install the GoPro camera Installation Method L R Insert The Batteries Remove the power switch cap, insert two 18350 batteries into the handle. Install The Camera Install the GoPro camera by the special Thumb Screw. And make sure it is fixed well. Power On Confirm the camera is installed well,then press the power button to turn on the Gimbal. Mode Switching When the Gimbal is working, you can press the function button to switch among the three working modes and a special working condition freely. (Details of working modes please refer to the instructions of working modes) Function Button Working Mode Instructions Operation Double Press Single Press Long Press For 1 Second LED Status Single Flashes Double Flashes On Constantly Function Explanation Operation Again Function Of Operation Again Heading Follow Mode Heading And Pitch Follow Mode Three Press Three Press again Other operation is arbitrary Other operation is arbitrary Other operation is arbitrary Other operation is arbitrary Single press again Single Flashes Inversion Mode Exit inversion mode to original state Exit standby mode , and awaken immediately Heading Lock Mode Long Press For 3 Second On Constantly Standby Mode Four Press Single Flashes Reset Function Button Instructions Heading, Pitch and Roll are all locked to Use for switch the working mode and realize other function The working mode and function can be identified by the LED status Heading Follow Mode Camera Pitch and Roll Angles remain Heading And Pitch Follow Mode Camera Roll Angle remains Heading Lock Mode Roll Pitch Heading constant, heading follows the handheld position. constant. Heading and Pitch follow the handheld position. point at one position.

Read Me First ! If any comments or suggestions please do not hesitate to e-mail us directly : [email protected] Thank you for supporting FY-G4 gimbal from Feiyu Tech ! FY-G4 is suitable for GoPro 4/GroPro 3+/GroPro 3, also can be compatible with GoPro LCD backpack and the cameras with the same size. EN Read Me First ! If any comments or suggestions please do not hesitate to e-mail us directly : [email protected] Thank you for supporting FY-G4 gimbal from Feiyu Tech ! FY-G4 is suitable for GoPro 4/GroPro 3+/GroPro 3, also can be compatible with GoPro LCD backpack and the cameras with the same size. EN

FEIYU-EN-1 Suitable for iPhone6 / 5C / 5S / 5 / 4S / 4 and similar ones. EN Indicator The indicator flashes in red light when in working, it will prompt the Gimbal at fault. Upgrade........ Adjust The Pitching Angle: Remote Control To Adjust: Customer can adjust the gimbal like mode switch or pitch angle by connecting remote control. Auto Adjust: Double press the function button to enter into“Heading And Pitch Follow Mode”. Hold the Gimbal at the desired angle, then press the button once to reengage “Heading Follow Mode” in order to lock the angle of desired pitch. Manual Adjust: Switch to heading follow mode or inversion mode,control the pitch angle to the the position you want, and keep for 0.5 second,the gimbal will lock current angle. Smooth And Steady Filming: Handheld the Gimbal, keep stable for movement, keep light and steady for walking. Please install the suitable smartphone first before power on the Gimbal. Attention ! Flexible Use Of Inversion Mode: Press the function button for three times in succession, the Gimbal switch to the inversion mode and help to captured low angle view more easily. If filming with moving forward at a high speed, keep the handle roughly parallel with the ground will be helpful. Filming Skill 4 1 Beginner Guide 2 Product Appearance Instructions 5 Function Interface Instructions Working Mode Instructions 3 Special Working Condition (Inversion Mode) When in any working mode, press the function button for three times in succession, the Gimbal enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset the Gimbal back to the original state. Hand Pulling Locking The pitching can be adjust by hand pulling after start the gimbal 8 seconds. During the Heading Follow Mode pulling the pitching to the desired angle and stay 0.5 second it will lock in the current angle. Standby Mode Press function button for 3 seconds, the motor stop working and the LED of the function button will single flashes this will indicate that gimbal enter the standby mode. Single press the function button the gimbal will be awaken immediately. Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware then unzip the RAR file.Remove the batteries and refer to the connection diagram to connect the gimbal with the computer. Please refer to the manual of update operation to upgrading,otherwise the Gimbal will be abnormal. The heading following speed can be configurate through parameter setting software.User can adjust to the desired following speed mode according to the requirements of filming scene. Three modes for optional: “SLOW” mode, “NORMAL” mode , “FAST” mode. Default setting is “FAST” mode. The Gimbal attitude can be calibrate through parameter setting software. User can adjust the pitch and roll in a small angle to achieve more accuracy filming scene. Please insert the batteries then refer to the connection diagram to connect the gimbal with the computer for caliration. Firmware Upgrade Instruction Parameters Configuration Gimbal Calibration PC Function Interface Indicator Explanation LED Status Explain Blue light flashes three times Full Power Blue light flashes twice Enough Power Blue light flashes once Low Power Blue light keeps flashing No Power Please Remove The Batteries Before Upgrading ! USB Cable USB Connector Attention : Please be sure to connect the computer with the USB connector. Attention : Please be sure to connect the computer with the USB connector. Attention : Please be sure to connect the computer with the USB connector. If any comments or suggestions please do not hesitate to e-mail us directly : [email protected] Attention: Be sure to connect the computer with the USB connector Remove the power switch cap, insert two batteries into the handle. Install the Smart phone by the quick-release adapter. And make sure it is fixed well. Power On Install The Phone Insert The Batteries Confirm the phone is installed well, then press the power button to turn on the Gimbal. Mode Switching When the Gimbal is working, you can press the function button to switch among the working modes and a special working condition freely. ( Details of working modes please refer to the instructions of working modes ) Item Double Press Single Press Long Press For 1 Second Long Press For 3 Second LED Status Single Flashes Double Flashes Function Explanation Item LED Status Explanation Heading Follow Mode Heading And Pitch Follow Mode Three Press Single Flashes Inversion Mode Pitch Recover Level Single Flashes Single Flashes Standby Mode Use for switching working modes. Function Button Identify the working mode via switch to different status of the indicator light. Heading Follow Mode：Camera Pitch and Roll Angles remain constant, heading follows the handheld position. Heading And Pitch Follow Mode：Camera Roll Angle remains constant. Heading and Pitch follow the handheld position. Working Mode Instructions 1. 2. G4 Handheld Gimbal For Smartphone Pitch Axis Heading Axis Function Interface Power Switch Roll Axis Function Button The USB Mini terminal of the cable plug into the function interface , the USB terminal plug into the USB connector. Please ensure to connect with the USB connector. Connection Mode In order to get the best working status , please try to keep the smart phone and pitch axis balance before power on the gimbal. Please refer to thefollowing: R Standard Installation Method 5 mm iPhone5 iPhone6 0 mm