Fellowes Startlet 2 120 Manuals

A 4 A 5 1 2 3 7 6 A 4 A 5 5 LOCATION OF CONTROLS 4 8 3 4 CAPABILITIES When punching; - always ensure the machine is on a stable surface - test punch scrap sheets and set the machine before punching final documents - remove staples and other metal articles prior to punching - never exceed the machines quoted performance - punch front and back covers first - punch sheets in small batches that do not overload the machine or the user - lift punch handle to open waste tray, when punch handle is down the waste tray is locked Punching Capacity Paper sheets - 70-80g / 20lb 10 sheets Transparent covers - 100-200 micron / 4-8 mil 2 sheets - 200+ micron / 8+ mil 1 sheet Other standard covers - 160-270g / 40-60 lb 2 sheets - 270+g / 60+ lb 1 sheet Binding Capacity Max comb size 16mm comb Max document (80g / 20lb) 120 sheets Technical Data Paper dimensions A4 Punching slots 21 (A4) Slot pitch 14.28mm / 9/16” Adjustable edge guide A4 or A5 Waste tray capacity 1000 sheets Net weight 3.3kg / 7.3lb Dimensions (HxWxD) 135(390) x 480 x 195mm 5.5”(15.5”) x 19” x 8” IMPORTANT SAFETY INSTRUCTIONS ENGLISH CAUTION - Please read before use and keep for future reference. 1. Punch handle 5. Waste tray 2. Edge guide selector 6. Carry handle 3. Paper entry 7. Document measure 4. Edge guide 8. Comb lever COMB DIAMETER & DOCUMENT SIZES LIGHT USE 16 MM MAX COMB SIZE 10 SHEETS PUNCH CAPACITY 120 SHEETS BIND CAPACITY LOCATION OF CONTROLS 6mm 1/4” 8mm 5/16” 10mm 3/8” 12mm 1/2” 16mm 5/8” 2-20 sheets 21-40 sheets 41-55 sheets 56-90 sheets 91-120 sheets 5 A4 A5 1. Ensure the machine is on a stable surface. Lift the punch handle to its upright position. BEFORE YOU BIND 2. Lift the punch handle. Check the waste tray is empty and correctly fitted. 3. Ensure the comb-opening mechanism is closed. STEPS TO BIND 1. Select either A4 or A5 paper size and test punch scrap sheets. Select the cor- rect comb diameter to suit the document (see chart). 2. Place the binding comb into the opening mechanism and fully engage the opening plate by sliding the comb to the left. 3. Open the binding comb by turning the comb lever. Take care not to open the comb too far. 1. Insert sheets fully into the punch slot. Align the sheets to the edge guide. 2. When all punched sheets are loaded onto the comb, close the comb lever. 3. To remove the document, slide the comb to the right and lift up the docu- ment. TROUBLESHOOTING Problem Possible cause Solution Punched holes are not central Edge guide not set Adjust edge guide until hole pattern is correct Machine will not punch Blockage Check waste tray is empty. Check for blockage to paper entry Punch holes are not parallel to edge Debris is stuck below dies Take stiff cardboard and slide into the paper entry. Move the cardboard sideways to release any stray clippings into the waste tray Partial holes Sheets not correctly aligned to punch pattern Adjust edge guide and test punch scrap sheets until correct Damaged hole edges Possibly overloading the machine Punch plastic covers with paper sheets. Reduce number of sheets being punched Waste tray leaks Waste tray is not correctly inserted or ‘burst feature’ has activated Check waste tray is empty and ‘burst feature’ is closed Cannot access document measure feature Document measure is part of the waste tray Check punch handle is fully raised then remove the waste tray & docu- ment measure A4 A5 A 4 A 5 A 4 A 5 A 4 A 5 SET UP