Finelite DL-C Manuals

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful Interference in which case the user will be required to correct the interference at his own expense. P L S L I G H T I N G FA C T S C M L A B E L S DESK LAMP UNDERCABINET - 12", 22", & 45" I N S T R U C T I O N S P E R S O N A L L I G H T I N G S Y S T E M P L S U S E & C A R E WARRANTY AND RETURN INFORMATION Finelite, Inc. warranties all Personal Lighting System components to be free from defects in materials and workmanship for a period of three years. Contact Finelite Inside Sales for return information if you have a warranty claim. TROUBLESHOOTING GUIDELINES What if the fixtures (Desk Lamps and Undercabinet) don't illuminate? • Check all connections. Is the connection to the supply voltage secure and fully inserted? • Is the power indicator LED illuminated? (21W and 60W power supplies only) — If the LED is not illuminated, contact Finelite. • Is the power supply “OCC SENSOR” switch in the “NO” position? • Are all low voltage connections secured and fully inserted? • Are all on/off fixture switches switched to “ON”? • Check to see that you have not exceeded a total of the maximum rated load of the power supply - disconnect fixtures until you are below maximum rated load. What if the fixtures “flash” when powered? • Check to see that you have not exceeded a total of the maximum rated load of the power supply - disconnect fixtures until you are below maximum rated load. • Cycle power on/off to power supply if necessary. What if the Occupancy Sensor does not turn off system? • Is the “OCC SENSOR” switch in the “YES” position? • Is the occupancy sensor connected to the power supply? • Does the indicator light on the occupancy sensor illuminate? (Note: It will only illuminate when sensing movement.) • Try turning the delay to a value between 30 minutes (max) and 30 seconds (min) on back of sensor (~10-15 minutes works best for most installations). • Consult occupancy sensor instruction sheet (supplied with sensor) for more information. What if the Occupancy Sensor turns the system off while seated at a station? • Make sure the occupancy sensor is set to a delay setting between min and max (10-15 minutes works best for most installations). • Make sure that the sensor window is not obstructed and facing towards your most common seated location. • For best results mount the occupancy sensor underneath your desk. CARE AND CLEANING OF THE PLS SYSTEM Your PLS system should operate trouble free for the life of the system. You may periodically wipe the system clean with a slightly damp soft cloth. Do not use any solvent or alcohol based cleaning products on plastic or painted surfaces or on the labels. Finelite, Inc. • 30500 Whipple Rd • Union City, CA 94587-1530 510-441-1100 • Fax 510-441-1510 • www.finelite.com P L S S Y S T E M POWER SUPPLIES DESK LAMP 45" UNDERCABINET 22" UNDERCABINET PATCH CABLE 12" UNDERCABINET UNDERCABINET 5" BASE WBC-S DL-C WEIGHTED BASES MOUNTING OPTIONS CLAMP CL-S MOUNTING PLATE MP-S POWER SUPPLY 21 WATTS PS-21W POWER SUPPLY 60 WATTS PS-60W POWER SUPPLY 8 WATTS PS-8W (INCLUDED W/ UC) SPLITTER CABLE OCCUPANCY SENSOR ( FOR 21W / 60W PS ONLY) DIF-110 POWER CABLE, SW POWER CABLE, SW RARE EARTH SUPER-MAGNETS PATCH CABLES [UC only] 3" CABLE, PATCH, UC • CP-3 6" CABLE, PATCH, UC • CP-6 14" CABLE, PATCH, UC • CP-14 28" CABLE, PATCH, UC • CP-28 POWER CABLES [UC only] 12’ CABLE, POWER N/SW, UC • CPN-12 SPLITTER CABLE [DL or UC] 6" CABLE, SPLITTER • CY-6 EXTENSION CABLE [DL or UC] 8’ CABLE, EXT • CX-8 © 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98384. 04/17 DESK LAMP MOUNTING UNDERCABINET POWER SUPPLIES 1” - 2.5” Drill 1.125 in. dia. (29mm) 1” - 2.5” Front Back Occupancy Sensor OCC SENSOR OCC SENSOR Yes No P L S I N S T R U C T I O N S FOR MORE INFO, SEE PLS OCCUPANCY SENSOR INSTRUCTION SHEET Rare earth super-magnets provided pre-installed for mounting directly on steel. NOTE: Remove rare earth magnets when installing with wood screws. Contact factory. Steel max min Time Delay Wood