Frigidaire AGQ7000EE - 5.8 cu.ft. Affinity Gas Dryer Manuals

All about the Installation of your Washer Important Safety Instructions ..............................2-3 Installation Requirements ...................................4-5 Installed Washer Dimensions .................................6 Unpacking Washer..............................................7-8 Installation Instructions ....................................9-10 Accessories .........................................................11 Notes .................................................................12 Français ..............................................................13 137168200C (1202) TABLE OF CONTENTS 2 IMPORTANT SAFETY INSTRUCTIONS WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. IMPORTANT IMPORTANT indicates installation, operation or maintenance information which is important but not hazard-related. DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Defi nitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Shipping Hardware ‰ Foam shipping support (under wash tub) removed and stored ‰ Shipping bolts and spacers removed from rear of appliance and stored ‰ Hole plugs (shipped in bag in drum) installed in holes in backsheet Leveling ‰ Washer is level, side-to-side and front-to-back ‰ Cabinet is setting solid on all corners Water Supply ‰ Rubber washers (shipped in drum) are installed in NEW inlet hoses (shipped in drum) ‰ HOT supply is connected to HOT inlet and COLD supply is connected to COLD inlet ‰ HOT and COLD water supply turned on ‰ No leaks present at water supply connections or appliance inlet connections - recheck in 24 hours Drain ‰ Stand pipe or wall drain height minimum 24” ‰ Drain hose snapped in “U” channel (shipped in drum) ‰ Drain hose secured in place with cable tie (shipped in drum) Electrical Power ‰ House power turned on ‰ Washer plugged in Final Checks ‰ Installation Instructions and Use and Care Guide read thoroughly ‰ Door locks and water enters drum when cycle starts ‰ Registration card sent in Installation Checklist CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. WARNING Please read all instructions before using this washer. Recognize safety symbols, words and labels Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described below: 3 IMPORTANT SAFETY INSTRUCTIONS Í NOTE The electrical service to the washer must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code C22.1 part 1. WARNING SUFFOCATION HAZARD Destroy the carton and plastic bags after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a garbage container or make materials inaccessible to children. CAUTION EXCESSIVE WEIGHT HAZARD To avoid back or other injury, have more than one person move or lift the washer. WARNING FIRE HAZARD For your safety the information in this manual must be followed to minimize the risk of fi re or explosion or to prevent property damage, personal injury or loss of life. Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance. IMPORTANT The instructions in this manual and all other literature included with this washer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance. Maximum benefi ts and enjoyment are achieved when all the Safety and Operating Instructions are understood and practiced as a routine with your laundering tasks. Tools and materials needed for installation: Save these instructions for future reference. Adjustable pliers Adjustable wrench 3/8” or 10 mm box wrench OR OR AND AND Ratchet and socket set Carpenter’s level WARNING FIRE HAZARD Do not stack a dryer on top of washer already installed on pedestal. Do not stack washer on top of dryer. Do not stack washer on top of another washer. Do not stack dryer on top of washer without use of manufacturer approved and correctly installed stacking kit appropriate for your model. 4 INSTALLATION REQUIREMENTS Í NOTE Because of potentially inconsistent voltage capabilities, the use of this washer with power created by gas powered generators, solar powered generators, wind powered generators or any other generator other than the local utility company is not recommended. WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. Í NOTE Drain hose attached to the washer can reach a 74 in. (188 cm) high standpipe. For higher standpipe, use hose P/N 137098000, available from an authorized parts distributor. Í NOTE GFI (Ground Fault Interrupter) receptacle is not required. CIRCUIT - Individual, properly polarized and grounded 15 amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker. POWER SUPPLY - 2 wire, with ground, 120 volt single phase, 60 Hz, Alternating Current. OUTLET RECEPTACLE - Properly grounded 3-prong receptacle to be located so the power supply cord is accessible when the washer is in an installed position. Grounding type Grounding type wa wall receptacl ll receptacle Po Power cord with wer cord with 3-prong 3-prong gr grounded plug ounded plug Do not, Do not, under under an any cir y circumstances, cumstances, cut, cut, remo remove ve, or b or bypass th ypass the gr grounding pr ounding prong. ong. 96” (244cm) max. 24” (61cm) min. Drain system requirements 1 Drain capable of eliminating 17 gals (64.3 L) per minute. 2 A standpipe diameter of 1-1/4 in. (3.18 cm) minimum. 3 The standpipe height above the fl oor should be: Minimum height: 24 in. (61 cm) Maximum height: 96 in. (244 cm) Water supply requirements Hot and cold water faucets MUST be installed within 42 inches (107 cm) of your washer’s water inlet. The faucets MUST be 3/4 inch (1.9 cm) with threading for laundry hose connection. Water pressure MUST be between 30 and 120 psi. Pressure difference between hot and cold cannot be more than 10 psi. Your water department can advise you of your water pressure. 1 The washer MUST be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. 2 Since your washer is equipped with a power supply Ground requirements Electrical system requirements cord having an equipment-grounding conductor and a grounding plug, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances or in the absence of local codes, with the National Electrical Codes, ANSI/NFPA 70 (latest edition). If in doubt, call a licensed electrician. DO NOT cut off or alter the grounding prong on the power supply cord. In situations where a two-slot receptacle is present, it is the owner’s responsibility to have a licensed electrician replace it with a properly grounded three prong grounding type receptacle.

www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352 All about the Use & Care of your Washer Important Safety Instructions ..............................2-4 Features ...............................................................5 Operating Instructions ......................................6-15 Stain Removal Guide ...................................... 16-17 Care and Cleaning .......................................... 18-21 Solutions to Common Problems ....................... 22-26 Warranty ............................................................27 Notes .................................................................28 Français ..............................................................29 TABLE OF CONTENTS 137168300C (1202) 2 IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance. This book contains valuable information about: • Operation • Care • Service Keep it in a safe place. Record Your Model and Serial Numbers The model and serial numbers of your washer are found on the washer serial plate located on the inside of the door. Record and retain these numbers. Model Number _____________________ Serial Number _____________________ Purchase Date _____________________ This Use and Care Guide provides general operating instructions for your washer. It also contains information about features for several other models. Your washer may not have every feature included. Use the washer only as instructed in this Use & Care Guide. Product Record Save these instructions for future reference. Í NOTE The instructions appearing in this Use and Care Guide are not meant to cover every possible condition and situation that may occur. Common sense and cau- tion must be practiced when installing, operating and maintaining any appliance. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. IMPORTANT IMPORTANT indicates installation, operation or maintenance information which is important but not hazard-related. DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Defi nitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. WARNING Please read all instructions before using this washer. Recognize safety symbols, words and labels Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described below: 3 IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fi re, electrical shock, or injury to persons when using this washer, comply with the basic warnings listed below. Failure to comply with these warnings could result in serious personal injuries. You can be killed or seriously injured if you don’t follow these Important Safety Instructions: PREVENT FIRE • Do not wash items that have been previously cleaned in, soaked in, or spotted with gasoline, cleaning sol- vents, kerosene, cooking oils, waxes, etc. Do not store these items on or near the washer. These substances give off vapors or chemical reactions that could ignite or explode. • Do not put oily or greasy rags or clothing on top of the washer. These substances give off vapors that could ignite the materials. • Do not add gasoline, cleaning solvents, or other fl am- mable or explosive substances to the wash water. These substances give off vapors that could ignite or explode. • Under certain conditions, hydrogen gas may be pro- duced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washer, turn on all hot water faucets and let the water fl ow from each for several minutes. This will release any accumulated hydrogen gas. Hydrogen gas is fl ammable; do not smoke or use an open fl ame during this time. • Do not store or use gasoline or other fl ammable vapors or liquids in the vicinity of this or any other appliance. • Failure to comply with these warnings could result in fi re, explosion, serious bodily injury and/or damage to the rubber or plastic parts of the washer. PROTECT CHILDREN • Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. As children grow, teach them the proper, safe use of all appliances. • Destroy the carton, plastic bag and other packing ma- terials after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads or plastic sheets can become airtight chambers. • Keep laundry products out of children’s reach. To pre- vent personal injury, observe all warnings on product labels. • Before the washer is removed from service or dis- carded, remove the washer door to prevent accidental entrapment. • Failure to comply with these warnings could result in serious personal injuries. 4 IMPORTANT SAFETY INSTRUCTIONS Grounding type Grounding type wa wall receptacl ll receptacle Po Power cord with wer cord with 3-prong 3-prong gr grounded plug ounded plug Do not, Do not, under under an any cir y circumstances, cumstances, cut, cut, remo remove ve, or b or bypass th ypass the gr grounding pr ounding prong. ong. PREVENT INJURY • To prevent shock hazard and assure stability during operation, the washer must be installed and electrically grounded by a qualifi ed service person in accordance with local codes. Installation instructions are packed in the washer for installer’s reference. Refer to INSTAL- LATION INSTRUCTIONS for detailed grounding procedures. If the washer is moved to a new location, have it checked and reinstalled by a qualifi ed service person. • To prevent personal injury or damage to the washer, the electrical power cord of the washer must be plugged into a properly grounded and polarized 3-prong outlet. The third grounding prong must never be removed. Never ground the washer to a gas pipe. Do not use an extension cord or an adaptor plug. • Follow package directions when using laundry products. Incorrect usage can produce poisonous gas - resulting in serious injury or death. • Do not combine laundry products for use in 1 load un- less specifi ed on the label. • Do not mix chlorine bleach with ammonia or acids such as vinegar. PREVENT INJURY AND DAMAGE TO THE WASHER To prevent serious personal injury and damage to the washer: • All repairs and servicing must be performed by an authorized servicer unless specifi cally recommended in this Use & Care Guide. Use only authorized factory parts. • Do not tamper with controls. • Do not install or store the washer where it will be ex- posed to the weather. • Do not install on carpet. Install washer on a solid fl oor. It may be necessary to reinforce the fl oor to prevent vibration or movement. • Do not sit on, step on or stand on the washer. Do not rest heavy loads on top. The washer is not meant to support weight. • To reduce the risk of electric shock, disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to the OFF position does not disconnect this appliance from the power supply. • To prevent injury, do not reach into the washer while parts are moving. Before loading, unloading or add- ing items, push in the cycle selector knob and allow the drum to coast to a complete stop before reaching inside. • This washer is equipped with an electrical overload pro- tector. The motor will stop if it becomes overheated. • Failure to comply with these warnings could result in serious personal injuries. WARNING FIRE/ELECTRICAL SHOCK HAZARD Avoid fi re hazard or electrical shock. Do not use an adaptor plug or extension cord or remove grounding prong from electrical power cord. Failure to follow this warning can cause serious injury, fi re or death. WARNING HARMFUL VAPOR HAZARD Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.

1 Washer Tech Data Sheet This information is intended for Qualified Technicians Only. CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING Please Return This Sheet to its Envelope in the Product for Future Reference Contents Page Error code explanation..........................................1 Diagnostics...........................................................1 Error Code Chart...................................................2 Tests..................................................................3-4 Français.............................................................5-8 Español............................................................9-14 6000 Wiring Diagram...........................................15 7000 Wiring Diagram...........................................16 READING ERROR CODES: 1. Wake the washer by pressing any button. 2. Wait 5 seconds. 3. Press and HOLD the Start/Pause and Cancel buttons simultaneously. As long as the buttons are held, the failure code will appear in the display as an E followed by two numbers, a number and a letter or two letters. The control will beep and the Door Lock, Wash, Rinse, and Final Spin indicator lights will flash. Troubleshoot the problem by using charts on the pages 3-5. Quick Check If there is no error displayed and the washer momentarily starts then turns back off: 1. Listen for a relay closure inside the motor control shortly after the Start/Pause key is pressed. If this happens, the motor control has power. 2. Check the 5 pin connector wiring between the console control and the motor control. NOTE: During normal operation, the display may show: “cd” - cool down (Sanitary cycle) “do” or “dr” - door problem. “Err” - an error has been detected. “LOC” - control lock is activated. “PAU” - cycle has been interrupted. To clear latest stored error code: • Turn the Program Knob to the start position, Spin Only. • Press Start/Pause to start the cycle and save it. • Press Cancel to stop the cycle and turn off the LEDs. • Press Cancel again to turn on the LEDs. • Within 5 seconds, press and hold the Option and Start/Pause buttons until LEDs start sequentially chasing, then release buttons. • Turn the program knob clockwise 7 clicks from the Start Position. The control will signal the last error code. • Press and hold the Options and Start/Pause buttons for 3 seconds. The code will be cleared. • Exit Diagnostic Mode to return the washer to normal operation. a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR b) Turn the program knob clockwise 2 or 3 clicks after the Start Position. Press Options and Start/Pause buttons together for a few seconds until wash cycle LEDs appear. Diagnostic Test The diagnostic test is used to check individual component function only. TO START THE TEST: • Turn the Program Knob to the start position, Spin Only. • Press Start/Pause to start the cycle and save it. • Press Cancel to stop the cycle and turn off the LEDs. • Press Cancel again to turn on the LEDs. • Within 5 seconds, press and hold the Options and Start/Pause buttons until LEDs start sequentially chasing, then release buttons. 1. All the LEDs will sequentially light. Pressing a button below a light cluster will light all the LEDs in that cluster at one time to confirm functionality. 2. Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water should enter through the detergent compartment. 3. Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water should enter through the bleach compartment. 4. Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and cold water should enter through the softener compartment. 5. Turn the program knob (4) clicks from the start position. The door lock solenoid will deactivate and the loading door can be opened. When the door is opened, the drum light should turn on. 6. Turn the program knob (5) clicks from the start position. The washer will fill and tumble. Once tumbling has started, the Boost Heater (if so equipped) will turn on. 7. Turn the program knob (6) clicks from the start position. The drain pump & door lock solenoid will activate and the washer will operate in high spin. SAFETY WARNING: If power is removed during this test, the door can be opened. To prevent injury, DO NOT put your hands inside when the tub is rotating. 8. Turn the program knob (7) clicks from the start position. The control will signal the last error code. Exiting Diagnostic Mode There are two options for exiting the Diagnostic Test mode and returning the washer to normal operation: a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR b) Turn the program knob clockwise 2 or 3 clicks after the start position. Press Options and Start/Pause buttons together for a few seconds until wash cycle LEDs appear. If a situation arises where you cannot exit the Diagnostic mode as described above and the bank of 5 LED’s on the right end remain ON regardless of Program Knob position, a combination of pushed buttons may have caused the control to enter a special factory test mode. Disconnect power to reset the control to return washer to normal operation is this occurs. 137063900C (1202) 2 Error code chart Error code Fault condition Check E11 Fill time too long. Refer to test (1). E13 Water leak in tub or air leak in air bell. Refer to test (2). E21 Water not pumping out fast enough. Refer to test (3). E23 Drain pump relay on control board failed, wire off pump or pump Replace console control board, wire or defective. pump. E24 Drain pump relay on control board failed. Replace console control board. E31 Pressure sensor not communicating with control board. Refer to test (4). E35 Pressure sensor indicates water overfill. Refer to test (5). E36 Console control board problem. Replace console control board. E38 Air chamber clogged or pressure sensor defective. Check air chamber, rpl press. sensor. E41 Control board thinks the door switch is open. Refer to test (6). E43 Console control board thinks the door locking device has failed. Refer to test (7). E44 Console control board problem. Replace console control board. E45 Console control board problem. Replace console control board. E46 Console control board problem. Replace console control board. E47 Console control board thinks the door PTC circuit is open in spin. Refer to test (7). E48 Console control board thinks the door PTC circuit is closed. Refer to test (7). E52 Bad signal from tacho generator. Refer to test (8). E56 High motor current. Refer to test (9). E57 High current on inverter. Refer to test (9). E58 High current on motor phase. Refer to test (9). E59 No tacho signal for 3 seconds. Refer to test (10). E5A High temperature on heat sink caused by overloading. Test first-if bad-rpl speed control brd. E5B High temperature on heat sink. Replace speed control board. E5C High temperature on heat sink. Replace speed control board. E5D Communication problem. Refer to test (11). E5E Communication problem. Refer to test (11). E5F Communication problem. Refer to test (11). E66 Heating element relay failure. Refer to test (14). E67 Input voltage on microprocessor incorrect. Refer to test (15). E68 Current leakage to ground on heater or fuse opened. Refer to test (14 & 15). E71 Wash NTC failure. Refer to test (15). E74 Wash temperature does not increase. Wire off NTC - rpl water valve. E75 Water temperature sensor circuit. Refer to test (12). E82 Console control board problem. Replace console control board. E83 Console control board problem. Replace console control board. E91 Comunnication error between UI board and console control board. Refer to test (16). E93 Console control board problem. Replace console control board. E94 Console control board problem. Replace console control board. E95 Communication error. Replace console control board. E97 Console control board problem. Replace console control board. E98 Console control board problem. Replace console control board. EB1 Incoming power frequency out of limits. Refer to test (13). EB2 Incoming line voltage above 130 VAC. Check voltage at outlet. If < 130VAC, replace the console control board. EB3 Incoming line voltage below 90 VAC. Check voltage at outlet. If > 90VAC, replace the console control board. EBE Console control board problem. Replace console control board. EBF Console control board problem. Replace console control board. EF1 Clogged drain pump. Unclog the drain pump. EF2 Too much soap. Advise customer to reduce the amount of soap they are using. 3 Test Test Check Correction Test 1: Test 2: Test 3: Test 4: Test 5: Test 6: Test 7: Yes. Go to step (4). No. Go to step (2) No. Turn water faucets on. Yes. Go to step (3). No. Have customer correct pressure problem. Yes. Check for kinked or blocked incoming water hoses, clean the incoming water screens. If problem still remains, replace the water inlet valve assembly. Yes. Go to step (5). No. Go to step (6) Yes. Go to step (6) No. Replace the inlet valve assembly. Pressure sensor checks good. Go to step (7). Pressure sensor checks bad. Replace pressure sensor. Yes. Correct water leak. No. Go to step (2) Yes. Correct the air leak problem. No. Go to step (3) Defective. Replace the pressure sensor. Good. Go to step (4) Restriction. Correct problem. No restriction. Go to step (2). Zero. Replace the control board. 120 VAC. Remove the pump and check for blockage. If blocked, remove the restriction, if not, replace the pump. Defective wiring. Correct wiring. Good wiring. Replace the pressure sensor. If this does not correct the problem, replace the control board. Yes. Go to step (2). No. Go to step (4). Yes. Go to step (3). No. Replace the control board. No. Replace water valve assembly. Yes. Check wiring to valve assembly for shorts. If wiring is good, replace the control board. Yes. Problem solved. No. Replace the control board. No. Close the door. Yes. Go the step (2). 0 volts. Check the door strike. If good, replace the door switch assembly. 120 volts. Replace the console control board. Washer spins. Defective door lock assembly. Washer does not spin. Defective control board. 1. Is the incoming water flow normal? 2. Are the incoming water faucets turned 3. Is the incoming water pressure above (30) psi. 4. Does the fill water continue to enter the washer? 5. Remove power from the washer. Did the water fill stop? 6. Check the pressure sensor. 7. Replace the control board. 1. Is the washer leaking water? 2. Is there an air leak in the air bell system? 3. Check the pressure sensor. 4. Replace the control board. 1. Check the drain hose for restrictions. 2. Start the washer and check for 120 VAC at the drain pump. Inspect the wiring between the pressure sensor and the control board. 1. Is the water level above 4.5 inches? 2. Does water enter the washer continuously. 3. Remove power from washer. Does the water stop coming in? 4. Replace the pressure sensor switch. Did this correct the problem? 1. Is the loading door closed? 2. In the J2 plug on the console control, measure voltage from the black wire to ground with power on. 1. Start the diagnostic test. Turn the program knob 8 clicks clockwise from the start position. 4 Test Test Check Correction 1. Disconnect the plug from the drive motor and measure the resistance pins 4 & 5 in the motor. 1. Remove the belt from the motor and spin the motor pulley. Does the motor spin free? 2. Spin the tub pulley. Does the tub spin free? 3. Disconnect the plug from the motor and measure the resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings should be between 4 and 6 Ohms. 1. Remove the belt from the motor and spin the motor pulley. Does the motor spin free? 2. Spin the tub pulley. Does the tub spin free? 3. Disconnect the plug from the drive motor and measure the resistance between pins 4 & 5 in the motor. 4. Disconnect the plug from the motor and measure the resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings should be between 4 and 6 Ohms. 1. Communication problem. Check the wiring between the control board and the speed control board. 1. Check the resistance of the water valve NTC. Is it around 50K ohms? 1. Have the power company check the frequency of the incoming power. If correct, replace the control board. 1. Check the resistance of the heating element. It should be approximately 14 ohms. 2. Check the resistance between ground and both heater terminals. It should be open when the heater terminals are disconnected. 1. Check the resistance of the tub NTC. Is it around 4.8K ohms? 1. Check the wiring harness between the console control board & the interface board. Test 8: Test 9: Test 10: Test 11: Test 12: Test 13: Test 14: Test 15: Test 16: If the reading is between 80 & 130 Ohms, replace the speed control board. If the meter reads other than between 80 & 130 Ohms, replace the motor. No. Replace the motor. Yes. Go to step (3) No. Check the tub bearings. Yes. Go to step (3) If the readings are correct, replace the speed control board. If the readings are incorrect, replace the motor. No. Replace the motor. Yes. Go to step (3) No. Check the tub bearings. Yes. Go to step (3) If the meter reads other than between 80 & 130 Ohms, replace the motor. If the reading is between 80 & 130 Ohms, Go to step (4) If the readings are correct, replace the speed control board. If the readings are incorrect, replace the motor. Wiring bad. Correct wiring problem. Wiring good. Replace the control board. If the problem is not corrected, replace the speed control board. No. Replace the water inlet valve assembly Yes. Replace the control board. If the readings are incorrect, replace the heating element. No, replace the heater assembly. Yes, check the wiring - if good, rpl console control board. If defective, correct wiring problem. If the harness is good and none of the LEDs light, replace the interface board. If this does not correct the problem, replace the console control board. Note: If only one of the LEDs will not light, replace the interface board.