FrontRow ezRoom ICR-01 Manuals

1. Most ICR-01, CM3000, and CM800Si installations house the components in an enclosure. The CMBT Bluetooth audio receiver works only in RF-friendly enclosures like the CMPL2 with plastic lid. Ensure that your enclosure meets this requirement before proceeding. 2. You can secure the CMBT receiver either to the metal enclosure mounting plate using the supplied mounting screws, or to the plastic lid using PT screws only (3.5 x 10mm / #6 x 3/8in). If mounting to the lid, ensure that CMBT receiver is installed in an area that will not interfere with other components when the lid is closed. (Image 1) 3. Plug the supplied UTP cable into the Intercom Port of the CMBT, and connect the other end to the Intercom port of the ICR-01, CM3000, or CM800Si. (Image 2) This will supply power to the CMBT. NOTE: If a device is already connected to the Intercom port of the ICR-01, CM3000, or CM800Si, proceed as follows: a. If the device is a CB85 ceiling mic, unplug it from the amplifier and reconnect it to the Intercom Mic (CB85) port on the CMBT. b. If the device is a CB75 wall mic with volume control, you can either leave it connected to the amplifier, and power the CMBT separately using a dedicated power supply or using a 5V patch cord from the amplifier (ICR-01 only) unplug it and consider installing a CB85 ceiling mic and CB55 volume/pairing control instead (see Step 4b below) c. If the device is a CB50 volume control, unplug it and consider installing a CB55 volume/pairing control instead (see Step 4b below) 4. Decide how you want to remotely initiate Bluetooth pairing: a. If you are using a CB6000 touch control panel, we recommend initiating pairing from the touch screen: a.1. Program Bluetooth pairing buttons for your CB6000 touch controller following the instructions in the CB6000 Installer Guide a.2. If you are using the ICR-01 Smart Receiver or CM800Si amp: a.ii. Locate the supplied relay cable and connect the white/neutral wire to the GND connector on the Ext Control terminal of the CMBT and connect the other end to the COM connector on one of the Relay terminals of the ICR-01 or to the R1-COM terminal of the CM800Si. (Image 3) a.ii. Connect the black/hot wire of the relay cable to the Relay connector on the Ext Control terminal of the CMBT and connect the other end to the NO connector on one of the Relay terminals of the ICR-01 or to the R1-NO terminal of the CM800Si. (Image 3) a.3. If you are using the CM3000 amp: a.iii. Locate the supplied infrared interface cable and connect the white/neutral wire to the GND connector on the Ext Control terminal of the CMBT and connect the other end to the IR- connector on the IR terminal of the CM3000. (Image 4) a.iii. Connect the black/hot wire of the interface cable to the IR In connector on the Ext Control terminal of the CMBT and connect the other end to the IR+ connector on the IR terminal of the CM3000. (Image 4) CMBT Bluetooth® Audio Receiver Installation Guide ICR-01 CM3000 CM800Si CMBT CMPL2 CB55A shown (CB55G and CB55I also available) Installation with ezRoom ICR-01 Smart Receiver, CM3000 amplifier/controller, or CM800Si amplifier Image 1 Image 2 Image 3 Image 4 Installation instructions continued on back side... OR OR OR OR 1530-00016/Rev A 0718 © 2018 FrontRow Calypso LLC Phonic Ear, FrontRow, Calypso and the names of Phonic Ear, Calypso, and FrontRow products are trademarks or registered trademarks of FrontRow Calypso LLC in the U.S. and other countries. Bluetooth is a registered trademark of Bluetooth SIG, Inc.

USER GUIDE ICR-01 Smart Receiver ITM-02 Pendant Microphone ISM-02 Pass-Around Microphone IMC-01 Microphone Charger

ICR-01 Smart Receiver INSTALLER GUIDE