FUTABA 3PM Manuals

❏1. Remove the antenna end cap and gently pull the antenna tube from the antenna mount on top of the receiver housing. Be careful not to damage the receiver antenna wire. ❏2. Remove the three body clips from the receiver box cover and remove the receiver cover from the chassis. ❏3. Disconnect the battery plug and three servo plugs from the stock receiver. Hint: This would be a good time to mark each servo connector so that you know what servo it controls (i.e. steering servo is #1, throttle servo is #2). Remove the receiver from the receiver mount. Clean off any excess servo tape left behind on the receiver mount. Hint: Use lighter fluid to clean the excess servo tape and adhesive from the receiver mount. ❏4. Install the Futaba R303FS receiver onto the receiver mount using new (not included) double sided tape. ❏5. Plug the receiver battery connector into the slot on the receiver marked “B/C.” ❏6. Plug the steering servo connector into the slot on the receiver marked channel 1. ❏7. Plug the throttle servo connector into the slot on the receiver marked channel 2. INSTALL THE RECEIVER Installing and Setting Up the Futaba® 3PM in the HPI Savage Before installing the radio system, read the Futaba 3PM instruction manual completely.

Thank you for purchasing a Futaba 3PM. Before using your 3PM, read this manual carefully and use your R/C set safely. After reading this manual, store it in a safe place. Application, Export, and Modification 1. This product may be used for models only. It is not intended for use in any application other than the control of models for hobby and recreational purposes. The product is subject to regulations of the Ministry of Radio/Telecommunications and is restricted under Japanese law to such purposes. 2. Exportation precautions: (a) When this product is exported from the country of manufacture, its use is to be approved by the laws govern- ing the country of destination which govern devices that emit radio frequencies. If this product is then re- exported to other countries, it may be subject to restrictions on such export. Prior approval of the appropriate goverment authorities may be required. If you have purchased this product from an exporter outside your coun- try, and not the authorized Futaba distributor in your country, please contact the seller immediately to determine if such export regulations have been met. (b) Use of this product with other than models may be restricted by Export and Trade Control Regulations, and an application for export approval must be submitted. In the US, use of 72MHz (aircraft only), 75MHz (ground models only) and 27MHz (both) frequency bands are strictly regulated by the FCC. This equipment must not be utilized to operate equipment other than radio controlled models. Similarly, other frequencies (except 50MHz, for HAM operators) must not be used to operate models. 3. Modification, adjustment, and replacement of parts: Futaba is not responsible for unauthorized modification, adjustment, and replacement of parts on this product. Any such changes may void the warranty. Compliance Information Statement (for U.S.A.) This device, trade name Futaba Corporation of America, model number R133F and R303FS comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The responsible party of this device compliance is; Futaba Corporation of America 2865 Wall Triana Highway, Huntsville, Alabama 35824, U.S.A. TEL (256) 461 - 7348 Battery Recycling (for U.S.A.) The RBRCTM SEAL on the (easily removable) nickel-cadmium battery contained in Futaba products indicates that Futaba Corporation of America is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States. The RBRCTM program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or mu- nicipal waste system, which is illegal in some areas. You may contact your local recycling center for information on where to return the spent battery. Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Futaba Cor- poration of America's involvement in this program is part of its commitment to protecting our environ- ment and conserving natural resources. NOTE: Our instruction manuals encourage our customers to return spent batteries to a local recycling center in order to keep a healthy environment. RBRCTM is a trademark of the Rechargeable Battery Recycling Corporation.