GE PEB2060SMSS - Countertop Microwave Oven Manuals

Microwave Oven PEB2060 Owner’s Manual Safety Information . . . . . . . . .2–6 Operating Instructions Auto Features . . . . . . . . . . . . . .12 Microwave Terms . . . . . . . . . . . .18 Other Features . . . . . . . . . . .16–18 Oven Features . . . . . . . . . . . . .7, 8 Power Levels . . . . . . . . . . . . . . . .9 Sensor Features . . . . . . . . . .13–15 Time Features . . . . . . . . . . . .9–12 Care and Cleaning . . . . . . . . .19 Troubleshooting Tips . . . . . . .20 Things That Are Normal . . . . . .20 Consumer Support Consumer Support . . .Back Cover Product Registration . . . . . .21, 22 Warranty . . . . . . . . . . . . . . . . . .23 MFL38268201 49-40551 04-07 JR ge.com Write the model and serial numbers here: Model # __________________ Serial # __________________ You can find them on a label inside the oven. Operating Instructions Safety Instructions Consumer Support Troubleshooting Tips IMPORTANT SAFETY INSTRUCTIONS. READ ALL INSTRUCTIONS BEFORE USING. For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. IMPORTANT SAFETY INSTRUCTIONS. When using electrical appliances basic safety precautions should be followed, including the following: I Read and follow the specific precautions in the Precautions to Avoid Possible Exposure to Excessive Microwave Energy section above. I This appliance must be grounded. Connect only to a properly grounded outlet. See the Grounding Instructions section on page 4. I Install or locate this appliance only in accordance with the provided installation instructions. I Be certain to place the front surface of the door three inches or more back from the countertop edge to avoid accidental tipping of the appliance in normal usage. I Do not mount this appliance over a sink. I Do not mount the microwave oven over or near any portion of a heating or cooking appliance. I Do not store anything directly on top of the microwave oven surface when the microwave oven is in operation. I Do not operate this appliance if it has a damaged power cord or plug, if it is not working properly, or if it has been damaged or dropped. If the power cord is damaged, it must be replaced by General Electric Service or an authorized service agent using a power cord available from General Electric. I Do not cover or block any openings on the appliance. I Use this appliance only for its intended use as described in this manual. Do not use corrosive chemicals or vapors in this appliance. This microwave oven is specifically designed to heat, dry or cook food, and is not intended for laboratory or industrial use. (a) Do Not Attempt to operate this oven with the door open since open-door operation can result in harmful exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks. (b) Do Not Place any object between the oven front face and the door or allow soil or cleaner residue to accumulate on sealing surfaces. (c) Do Not Operate the oven if it is damaged. It is particularly important that the oven door close properly and that there is no damage to the: (1) door (bent), (2) hinges and latches (broken or loosened), (3) door seals and sealing surfaces. (d) The Oven Should Not be adjusted or repaired by anyone except properly qualified service personnel. PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY 2 WARNING! Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions ge.com IMPORTANT SAFETY INSTRUCTIONS. Use this appliance only for its intended purpose as described in this Owner’s Manual. I This microwave oven is not approved or tested for marine use. I Do not store this appliance outdoors. Do not use this product near water—for example, in a wet basement, near a swimming pool, near a sink or in similar locations. I Keep power cord away from heated surfaces. I Do not immerse power cord or plug in water. I Do not let power cord hang over edge of table or counter. I To reduce the risk of fire in the oven cavity: —Do not overcook food. Carefully attend appliance when paper, plastic or other combustible materials are placed inside the oven while cooking. —Remove wire twist-ties and metal handles from paper or plastic containers before placing them in the oven. —Do not use the oven for storage purposes. Do not leave paper products, cooking utensils or food in the oven when not in use. —If materials inside the oven ignite, keep the oven door closed, turn the oven off and disconnect the power cord, or shut off power at the fuse or circuit breaker panel. If the door is opened, the fire may spread. —Do not use the Sensor Features twice in succession on the same food portion. If food is undercooked after the first countdown, use Time Cook for additional cooking time. I See door surface cleaning instructions in the Care and cleaning of the microwave oven section of this manual. I This appliance must only be serviced by qualified service personnel. Contact nearest authorized service facility for examination, repair or adjustment. I As with any appliance, close supervision is necessary when used by children. SAVE THESE INSTRUCTIONS ARCING If you see arcing, press the CLEAR/OFF pad and correct the problem. Arcing is the microwave term for sparks in the oven. Arcing is caused by: I Metal or foil touching the side of the oven. I Foil not molded to food (upturned edges act like antennas). I Metal, such as twist-ties, poultry pins or gold- rimmed dishes, in the microwave. I Recycled paper towels containing small metal pieces being used in the microwave. WARNING! 3

PART QUANTITY ❒ Trim Frame 1 ❒ Bottom Duct 1 ❒ Side Duct 1 ❒ 4 mm x 12 mm 23 Round-Head Screws (21 required for installation) ❒ 4 mm x 14 mm 6 Flat-Head Screws (4 required for installation) ❒ Anti-Tip Brace 1 ❒ Anti-Tip Bracket 1 ❒ Upper Duct 1 ❒ Top Bracket 1 ❒ Bottom Bracket 1 ❒ Templates 2 PARTS INCLUDED Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com READ CAREFULLY. KEEP THESE INSTRUCTIONS. Installation Built-In Trim Kits Instructions JX2027 and JX2030 Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. • IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference. • For easier installation and personal safety, we recommend that two people install this microwave oven. WARNING — This oven must be plugged into a properly grounded 3-hole, 120V receptacle as required by the National Electrical Code. ❒ BEFORE YOU BEGIN • Do not alter or modify any part of this kit or the oven. • Unplug the microwave oven before attempting installation of this kit. • Skill level – Installation of this appliance requires basic mechanical and electrical skills. • Completion time – 1-3 hours • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty. • This kit is UL listed for installation alone or over any GE/GE Profile single electric wall oven. Not for use adjacent to (within 2 feet of) any gas or electric range, cooktop or oven. • This kit is for use on models: PEB2060DMBB, PEB2060DMWW, PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW, JEB1860DMCC and JEB1860SMSS. TOOLS YOU WILL NEED ❒ Phillips screwdriver ❒ Pencil ❒ Tape measure ❒ Awl or punch ❒ Drill with 7⁄64″ bit or #35 FOR YOUR SAFETY: WARNING – Before beginning the installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. ❒ Level ❒ Scissors (optional) 1 NOTE: This kit has extra screws to prevent the technician from spending extra time locating a replacement screw in case they lose one during installation. ❒ CUTOUT DIMENSIONS 1 2 * Min. depth with receptacle outside cabinet 191⁄2″ Min. depth with receptacle inside cabinet 22″ 120 volt-60 Hertz grounded power receptacle Installation Instructions Models 27″ 30″ Height 163⁄4″ 163⁄4″ Width 251⁄2″ 251⁄2″ Depth (min.)* 191⁄2″ or 22″ 191⁄2″ or 22″ WARNING — This trim kit uses air flow from the top, bottom and sides of the trim frame. Blocking the air flow can cause the microwave to function improperly and may cause damage to the microwave. Allow a 1″ clearance beyond the edge of the trim frame to provide proper air flow. On 27″ models, allow 11⁄8″ at the top, 11⁄16″ on the sides and 11⁄4″ at the bottom for overlap of the Trim Frame over the edges of the cutout. On 30″ models, allow 11⁄8″ at the top, 21⁄16″ on the sides and 11⁄4″ at the bottom for overlap of the Trim Frame over the edges of the cutout. FOR INSTALLATION ABOVE A BUILT-IN OVEN: Microwave oven should be installed on a 3/8″ plywood base and supported by 2x4 or 1x2 equivalent runners on all sides. Base must be capable of supporting a minimum of 100 lbs. Draw a line on the cutout floor at the center of the cutout, and extend the line 1/2″ down the face of the cabinet. Draw a line on the top front face of the cabinet at the center of the cutout. The line should extend 1/2″ up the face of the cabinet. This center line will be used for mounting the top bracket (see step 7). Fold or cut the front edge of the template, along the front guide line. Place the template flush along the front edge of the cutout floor, aligning the center line of the template with the center line of the cutout floor. Mark the center positions with an awl or center punch for the anti-tip brace location as shown. Drill two holes for the anti-tip brace. Install the anti-tip brace onto the cutout floor using two round-head screws. B C D E D D Round-head screws (2) Anti-Tip Brace ❒ INSTALL THE ANTI-TIP BRACE 2 Depth Height 11⁄4″ Overlap Width 11⁄8″ Overlap 1″ Clearance beyond trim frame (on all sides) 3″ Min. 27″ Models: 11⁄16″ overlap 30″ Models: 21⁄16″ overlap A DIMENSIONS: A = 11⁄2″ B = 3″ C = 183⁄16″ D = 1/2″ Bottom of trim kit must be minimum of 36″ from floor 3 Disconnect the microwave oven before proceeding with the installation. Fasten the anti-tip bracket to the bottom duct by using four round-head screws. Remove any loose items inside the microwave oven, including the turntable and turntable support. Carefully turn the microwave upside down. Install bottom duct with four round-head screws as shown. A C B D Front Rear Round-Head Screws (4) Installation Instructions Set the microwave upright, being careful not to bend the front flange. Remove the one existing screw from the left side of the microwave oven. As indicated on the supplied template (publication #31-41003), fold or cut along the “cut lines” and place the template on top of the microwave oven. By aligning the template with the outside edges of the oven, you will see exactly where to place the upper duct assembly. Peel off the backing from the double-sided tape. Carefully position the side duct and upper duct assembly on the microwave cabinet, aligning with the bottom screw hole. Press down firmly on the ducts. Fasten the duct assembly to the left side of the cabinet with the screw removed above. B C Existing Screw (1) Round-Head Screws Microwave Oven Upside Down ❒ INSTALL ANTI-TIP BRACKET AND BOTTOM DUCT 3 ❒ INSTALL SIDE DUCT AND UPPER DUCT (cont.) 4 Slide the microwave oven part way into the cabinet opening. Plug in the microwave oven. The anti-tip bracket must be flat to the cutout floor to engage correctly with the anti-tip brace as shown. Carefully slide the microwave back, making sure the power cord is not mashed or cut. Center the microwave oven within the cutout opening and slide the microwave oven in place, engaging the anti-tip brace. Ensure the microwave oven is accurately centered. A B C Anti-Tip Assembly Bottom Duct Round-Head Screw Anti-Tip Bracket Anti-Tip Brace D E ❒ INSTALL MICROWAVE OVEN INTO CABINET 5 Connect the side duct to the upper duct as shown. 1. Insert projecting tabs of the upper duct into the holes of the side duct. 2. Bend the tabs up with caution as shown. NOTE: Remove any oil or dirt on the surface of the microwave oven before the ducts are attached. A (2) (1) Upper Duct Side Duct 3 Tabs 3 Holes ❒ INSTALL SIDE DUCT AND UPPER DUCT 4

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. 240374 Specification Revised 2/11 Listed by Underwriters Laboratories PEB2060SM GE Profile™ 2.0 Cu. Ft. Countertop Microwave Oven Dimensions and Installation Information (in inches) Optional Accessory Trim Kits for 2.0 GE Microwave Ovens (Available at additional cost) For a custom built-in appearance, these kits allow built-in installation of the countertop microwave oven into a wall or cabinet alone and are U.L. approved for installation over a GE single electric wall oven. These kits should not be installed over a gas wall oven. Note: 120V, 60-cycle, grounded power receptacle location optional on back within cabinet opening. Installation Information: This information is not intended to be used for installing unit described. Before installing, consult installation instructions packed with product/kit for current dimensional data. Exterior Dimensions (in inches) W x H x D 24 x 13-3/4 x 19-3/8 16-3/4 ± 1/16 22" MIN. receptacle in cabinet 19-1/2" MIN. receptacle outside cabinet 19 Z Bracket 25-1/2 ± 1/8 Trim Kit 36" MIN. Cabinet overlap requirements 27” 30” A - Overlap of trim kit over top of cabinet 1-1/8” 1-1/8” B - Overlap of trim kit over bottom of cabinet 1-1/4” 1-1/4” C - Overlap of trim kit over sides of cabinet 11/16” 2-1/16” Note: Allow an additional inch of clearance beyond trim frame on all sides B A C Accessory trim kits "Z" Trim Kits Max Height 30" Deluxe 29-3/4" JX2030SMSS 19-1/16" 27" Deluxe 26-15/16" JX2027SMSS 19-1/16" Note: Allow an additional inch of clearance beyond trim frame on all sides. For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. 240374 Specification Revised 2/11 Listed by Underwriters Laboratories PEB2060SM GE Profile™ 2.0 Cu. Ft. Countertop Microwave Oven PEB2060SM START PAUSE CLEAR OFF HELP CLOCK REMINDER AM/PM BEEPER VOLUME DELAY START Features and Benefits • 2.0 Cu. Ft. Capacity - 1200 Watts (IEC-705 test procedure) • Sensor Cooking Controls - Automatically adjust the time and power for exceptional cooking results • Optional Trim Kit - Offers a built-in appearance of a countertop model • Auto and Time Defrost - Automatically defrosts for a specified amount of time • Turntable - Continually rotates food to ensure even cooking • Instant On Controls - Allow quick, one-touch cooking and reheating • Child Lock Out - Enables you to lock the keypad to prevent the oven from being accidentally started • Kitchen Timer - Operates as a minute timer and can be used at any time, even when the oven is operating • Add 30 Seconds - Increases cooking times with one touch • Electronic Touch Controls - Offer easy point-and-cook convenience • Model PEB2060SMSS – Stainless steel