Goldair GDF120B Manuals

12” (30cm) Desk Fan MODEL: GDF120B Instruction Book Visit our web site at: www.buyprima.com IMPORTANT SAFEGUARDS Please keep these instructions 1. Check that the mains voltage corresponds with the rating of the appliance before opening. 2. Read all instructions. 3. To protect against electric shock, do not immerse cords, plugs or appliances in water or any other liquid. 4. Do not leave any appliance unattended while it is operating. 5. Close supervision is necessary when any appliance is used by or near children or infirm persons. 6. Unplug from outlet when not in use or before cleaning. 7. Do not operate the appliance with a damaged cord or plug, or after the appliance has been damaged in any manner. If the supply cord or appliance is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. 8. The use of accessory attachments not recommended by the appliance manufacturer may cause injuries. 9. Do not use outdoors. 10. Do not let the cord hang over the edge of a table or counter or let it come into contact with any hot surfaces. 11. To disconnect – remove the plug from the outlet. Do not pull plug out by the cord. 12. this appliance should not be used in the immediate vicinity of water, such as a bath tub, sink, swimming pool etc. where there is a risk of splashing. 13. Do not use this product for anything other than its intended use. This appliance is for household use only. 14. No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling. 15. Always use the fan on a flat, stable surface. 16. Do not insert objects through the guard whilst the fan is operating. 17. Do not cover the grill, or operate in close proximity to curtains etc. Assembly This fan is supplied with a surround based that must be fitted to the fan BEFORE the fan is used. The surround base is supplied with a small bag of two screws, which must be used to secure the base in place: Position the surround base above the bottom of the motor housing assembly and line up with the Locking Lug and push down until locked into place. Screw the two screws into the holes in the middle of the base for extra support. DO NOT over tighten the screws. To remove the base for cleaning purposes, remove retaining screws and unclip the surround base. DO NOT operate the fan with the base surround removed. To assemble to fan and grille • Place the Rear Grille onto the Motor Housing Top and align the Locating Pegs. NOTE: The small screw hole should be at the bottom of the fan • Next place the Grille Retaining Ring onto the Motor Housing Top and turn to tighten and secure. • Slide the Fan Blade over the motor shaft ensuring that it is firmly seated and fit the blade retaining knob and turn anti-clockwise to tighten. • Loosen the nut on the back of the Front Grille and unscrew the screw from the front of the Front Grille. • Open the 3 grill clamps on the front blade cover and fit the edge of the back cover into the slot on the rim of the front cover, align screw holes, and close clamps. • Fit nut and screw and tighten. Instructions for use Plug into 230V AC mains outlet and select desired speed. 0 – Off 1 – Low Speed 2 – Medium Speed 3 – High Speed Pressing the Oscillation knob located on the top/back of the Motor Housing will cause the fan to sweep back and forth. Lifting the oscillation knob will stop the sweeping motion of the fan. The inclination of the fan head may be adjusted by loosening the tilt adjustment screw lifting the Motor Housing Head to the position needed. Tighten the screw up when correct position is found NOTE: This should only be done when the fan is switched off. Cleaning and Maintenance • Switch off the power supply and pull out the plug from the mains socket before cleaning. • A soft dry cloth is usually adequate but can be moistened with mild detergent solution if required. • Never clean the unit with solutions such as thinners and polishing powder etc.