Hanna Instruments HI 991002 Manuals

Instruction Manual HI 991002 Extended Range Waterproof pH / ORP / Temperature Meter Dear Customer, Thank you for choosing a Hanna Instruments Product. Please read this instruction manual care- fully before using the instrument. If you need additional technical information, do not hesi- tate to e-mail us at [email protected] This instrument is in compliance with the directives. All Hanna Instruments meters are warranted for two years against defects in workmanship and materials when used for their intended pur- pose and maintained according to instructions. The probes are warranted for a period of six months. This warranty is limited to repair or replacement free of charge. Damage due to accidents, mis- use, tampering or lack of prescribed maintenance are not covered. If service is required, contact the dealer from whom you purchased the instrument. If under warranty, report the model number, date of pur- chase, serial number and the nature of the prob- lem. If the repair is not covered by the warranty, you will be notified of the charges incurred. If the instrument is to be returned to Hanna Instru- ments, first obtain a Returned Goods Authoriza- tion Number from the Customer Service depart- ment and then send it with shipment costs pre- paid. When shipping any instrument, make sure it is properly packaged for complete protection. All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner. WARRANTY PRELIMINARY EXAMINATION Remove the instrument from the packing material and examine it carefully to make sure that no damage has occurred during shipment. If noticeable damage is evident, notify your dealer. Note: Save all packing material until you are sure that the instrument func- tions correctly. All defective items must be returned in the original packing together with the supplied accessories. HI991002 is a portable, microprocessor- based pH/ORP/temperature meter. Main features include: extended pH, mV and temperature ranges; waterproof and compact casing; large dual-line display; low battery detection; automatic pH calibration at one or two points with two memorized buffer sets (standard or NIST); selectable temperature unit (°C or °F). The pH electrode has a built-in tempera- ture sensor for simultaneous pH (or pH- mV) and temperature readings, and also contains a mini amplifier to render mea- surements impervious to noise and elec- trical interferences. Each meter is supplied complete with: • HI1296D pH/temperature probe with DIN connector and 1 m (3.3’) cable • calibration & cleaning solution sachets • 3x1.5V AA alkaline batteries • instruction manual • rugged carrying case. GENERAL DESCRIPTION SPECIFICATIONS Range (*) -2.00 to 16.00 pH ±1999 mV -5.0 to 105.0°C / 23.0 to 221.0° Resolution 0.01 pH 1 mV 0.1°C / 0.1°F Accuracy ±0.02 pH (@20°C/68°F) ±2 mV ±0.5°C up to 60°C; ±1°C outsid ±1°F up to 140°F; ±2°F outsid Typical EMC ±0.02 pH Deviation ±2 mV ±0.2°C or ±0.4°F Temperature Automatic for pH reading Compensation pH Calibration Automatic, 1 or 2 poin with 2 sets of memorized buffer (pH 4.01/7.01/10.01 or 4.01/6.86/9.18 ORP Calibration Factory calibrate Probe (included) HI 1296D amplified pH/temperatur probe with DIN connector and 1 m (3.3’) cabl Battery Type 3 x 1.5V AA / IEC LR Battery Life Approx. 1500 hour Auto-off After 8 minutes of non-us Environment 0 to 50°C (32 to 122°F) RH max 100% Dimensions 150 x 80 x 36 mm (5.9 x 3.1 x 1.4” Weight 210 g (7.4 oz (*) the temperature range is limited to 80°C (176°F) using the HI1296D or HI1297D probes. To clean the meter, use water only. HI 1296D Combination amplified pH/ temperature probe with DIN connector and 1 m (3.3’) cable HI 1297D Combination amplified pH/ ORP/temperature probe with DIN and 1 m (3.3’) cable HI 7004L pH 4.01 buffer solution, 500 mL HI 7006L pH 6.86 buffer solution, 500 mL HI 7007L pH 7.01 buffer solution, 500 mL HI 7009L pH 9.18 buffer solution, 500 mL HI 7010L pH 10.01 solution, 500 mL HI 70300L Storage solution, 500 mL HI 7061L Cleaning solution, 500 mL HI 710007 Blue shockproof rubber boot HI 710008 Orange shockproof rubber boot HI 721312 Rugged carrying case HI 76405 Electrode holder ACCESSORIES LCD DESCRIPTION IST991002R2 07/0 1. Automatic Temperature Compensation indicator 2. Stability indicator 3. Battery percentage 4. pH calibration indicator 5. Low battery indicator 6. Selectable temperature unit 7. Secondary display 8. Primary display 9. Measuring unit for primary display w w w . h a n n a i n s t . c o m Hanna Instruments reserves the right to modify the design, construction and appear- ance of its products without advance notice. To connect the probe With the meter turned off, connect the HI1296D probe to the DIN socket on the top of the meter by aligning the pins and pushing in the plug. Tighten the nut to ensure a good connection. Remove the protective cap from the probe before taking any measurements. To turn meter ON and check battery status Press the ON/OFF/MODE button until the display lights up. At start-up, all the LCD segments are displayed for 1 second, then the percent indica- tion of the remaining battery life is shown for an- other second (E.g. % 100 BATT). The meter then enters the normal measuring mode. Note: If the display needs to be checked, keep the ON button pressed while turning the meter on. The meter will display all segments as long as the button is pressed. To select the measurement range While in normal measurement mode, press the SET/HOLD button to select pH or mV (pH- mV or ORP, depending on probe) measure- ment range. To freeze the display While in measurement mode, press the SET/ HOLD button until HOLD appears on the second- ary display; the reading will be frozen on the LCD (E.g. pH 5.73 HOLD). Press any button to return to normal mode. To turn the meter OFF While in normal measurement mode, press the ON/OFF/MODE button. OFF will appear on the secondary display. Release the button. Note: The meter is provided with an acoustic sig- nal feature, which can be disabled using the switch located in the battery compartment. Note: When the meter detects the absence of a temperature probe at its input, the Automatic Temperature Compensation is turned off, and the meter uses a default value of 25°C (77°F) for the temperature measurement and com- pensation. In this condition, the secondary LCD shows 25.0°C (77.0°F) blinking. When a probe is connected, the meter automatically returns to the ATC mode, the ATC tag is turned on, and the temperature is shown on the secondary display. OPERATIONAL GUIDE METER SETUP pH MEASUREMENT & CALIBRATION • Make sure the probe is connected. • Set the meter to mV range. • Place the probe into the sample to be tested. • Stir briefly and wait until the ¹ symbol on the top left of the LCD is turned off. • If using supplied HI1296D probe, the meter will show the mV value equivalent to the pH and the temperature of the sample; if using optional HI1297D probe, the meter will show the ORP (mV) value and the temperature of the sample. Note: The ORP range is factory calibrated. Note: ATC tag turns off because the mV readings are not temperature compensated. ORP MEASUREMENT BATTERY REPLACEMENT Setup mode allows the selection of the tempera ture unit and of the pH buffer set. To enter the Setup mode, press and hold the ON OFF/MODE button until CAL on the secondary dis play is replaced by TEMP and the current tempera ture unit (E.g. TEMP °C). Then: • for °C/°F selection, use the SET/HOLD button After the temperature unit has been selected press ON/OFF/MODE to enter the buffer set se lection mode; press ON/OFF/MODE twice to re turn to the normal measuring mode. • to change the calibration buffer set, after settin the temperature unit, the meter will show th current buffer set: “pH 7.01 BUFF” (for 4.01/7.01 10.01) or “pH 6.86 BUFF” (for 4.01/6.86/9.18 Change the set with the SET/HOLD button, the press ON/OFF/MODE to return to normal mode • Make sure the meter has been calibrated before use. • If the probe is dry, soak it in HI70300 storage solution for one hour to reactivate it. • Place the tip of the probe into the sample to be tested. • Stir briefly and wait until the ¹ symbol on the top left of the LCD is turned off. • The LCD shows the pH value (automatically compensated for temperature) on the primary LCD, while the secondary LCD shows the tem- perature of the solution. • If measurements are taken in different samples successively, rinse the probe tip thoroughly to eliminate cross-contamination. After cleaning, rinse the probe tip with some of the sample to be measured. pH calibration • From normal mode, press and hold the ON/OFF/ MODE button until OFF on the secondary display is replaced by CAL. Release the button. • The LCD enters the calibration mode, display- ing “pH 7.01 USE” (or “pH 6.86 USE” if the NIST buffer set was selected). After 1 second the meter activates the automatic buffer recognition fea- ture. If a valid buffer is detected, then its value is shown on the primary display, and REC appears on the secondary LCD. If no valid buffer is de- tected, the meter keeps the USE indication ac- tive for 12 seconds, and then replaces it with WRNG, indicating that the sample being mea- sured is not a valid buffer. • For a single-point calibration with buffers pH 4.01, 9.18 or 10.01, the meter automatically accepts the calibration when the reading is stable; the meter will show on the primary display the ac- cepted buffer, with the message “OK 1” on the secondary display, and an audible signal is pro- duced. After 1 second the meter automatically returns to the normal measuring mode. If a single-point calibration with buffers pH 7.01 or 6.86 is desired, then after the calibration point has been accepted the ON/OFF/MODE button must be pressed in order to return to the normal measuring mode. After the button is pressed, the meter shows "7.01" (or "6.86") - "OK 1", and an audible signal is produced. After 1 second, the meter automatically returns to the normal measuring mode. Note: It is always recommended to carry out a two- point calibration for better accuracy. • For a two-point calibration, place the probe in pH 7.01 (or pH 6.86) buffer. After the calibration point has been accepted, the “pH 4.01 USE” mes- sage appears. The message is held for 12 sec- onds, unless a valid buffer is recognized. If no valid buffer is recognized, then the WRNG mes- sage is shown. If a valid buffer (pH 4.01, pH 10.01 or pH 9.18) is detected, then the meter completes the calibration procedure. When the buffer is accepted, the LCD shows the accepted value with the “OK 2” message on the second- ary display. The meter then returns to the normal measuring mode. Note: When the calibration procedure is completed, the CAL tag is turned on. To quit calibration and to reset to the default values • After entering the calibration mode and before the first point is accepted, it is possible to quit the procedure and return to the last calibration data by pressing the ON/OFF/MODE button. The sec- ondary LCD displays ESC for 1 second and the meter returns to normal mode. • To reset to the default values and clear a previ- ous calibration, press the SET/HOLD button af- ter entering the calibration mode and before the first point is accepted. The secondary LCD displays CLR for 1 second, the meter resets to the default calibration and the “CAL” tag on the LCD disappears. The meter displays the remaining battery per centage when turned on. When the level is be low 5%, the - + symbol on the bottom left o the LCD blinks to indicate a low battery cond tion. If the battery level is low enough to caus erroneous readings, the Battery Error Preven tion System (BEPS) turns the meter off. Unscrew the 4 screws located on the back o the meter and carefully replace the 3 AA batter ies located in the battery compartment, whil paying attention to their polarity. Reattach th back making sure that the gasket is in plac and tighten the 4 screws to ensure a water tight seal.