Henny Penny LOV LVE-100 Series Manuals

1. Put on protective gear: Use all McDonald’s approved safety equipment including, Apron, Face Shield and Gloves. Hot oil can cause severe burns. 2. Press and hold (on either side) until display shows 1.AUTO FILTER?. 3. Press and release and display shows 2.MAINT FILTER?. Press √√√√√ button and display shows “PUT ON *PPE*, followed by CONFIRM? and YES NO. 4. Press √√√√√ and display shows DRAINING and the oil drains from the vat, or press X button for NO and controls return to normal operation. 5. If filtering is desired, press √√√√√ button for YES and display shows DRAINING and the oil drains from the vat. Gas units, continue to step 7. 6. Electric units only. Use the lift tool and lift the hinged element to clean the bottom of the vat. Use care not to damage high limit bulb. Figure 1. 7. Use the scouring tool, a nylon scouring pad, and a small amount of McD Fryer Cleanser to scrub the inside of the vat. Be careful not to damage the sensing probes. 8. Once the vat is clean and the display shows SCRUB COMPLETE?, and YES NO. Press √√√√√ and the display shows WASH VAT?, and YES NO. 9. Lower the elements (electric units only) and press √√√√√ and display shows WASHING. Once the wash cycle is complete, display shows WASH AGAIN?, and YES NO. 10. Press √√√√√ if another wash is needed, otherwise press X button for NO and the display shows RINSING. When rinsing is complete, display shows RINSE AGAIN?, and YES NO. 11. Press √√√√√ if another rinse is needed, otherwise press X button for NO. Display shows POLISH, and YES. 12. Press √√√√√ button and the oil is “polished” and the display shows 5:00, followed by STOP POLISH. If desired, press X button for STOP to stop the polishing, otherwise the oil is polished for 5 minutes. 13. The display shows FILL VAT?, and YES NO. Press √√√√√ and display shows FILLING and vat fills with oil. 14. Once full, display shows IS POT FILLED?, and YES NO. Press √√√√√ and fryer returns to normal operation. MAINTENANCE FILTER (End of Day Manual Filter) Any problems, refer to manual or contact Henny Penny Corp. 1-800-417-8405, or 937-456-8405. These instructions are meant to be guidelines, not complete operating instructions. Read and understand the complete operater’s manual supplied with each unit. Figure 1 The filter pad or paper must be replaced daily! 3-20-08 FM07-306-A

1. Press and hold and buttons until LEVEL - 1 shows in the display, followed by ENTER CODE. 2. Enter code 1, 2, 3, 4. “PRODUCT” and “SELECTN” show in the displays. 3. Press √√√√√ button and ‘SELECT PRODUCT’ and “-P 1-” show in the displays. 4. and buttons scrolls through the 40 products, or press the desired product button 5. Press √√√√√ button and the product shows in the left display and “MODIFY”, and “YES NO” shows in the right display. Press √√√√√ button to change this product, or press X button to choose another product. 6. If √√√√√ button was pressed, use the product buttons to enter product name. Once the desired letter shows in the display, press button to continue to the next letter. 7. Once name is complete, press button and “COOK TIME” shows in the display. Use the product buttons to change the time in minutes and seconds, to a maximum of 59:59. 8. Press button and “TEMP” shows in the display. Press the product buttons to change the temperature. The temperature range is 190°F (88°C) to 380°F (193°C). 9. Press button and “COOK ID” shows in the display. Enter abbreviated product name (Ex: NUG) 10. Press button and “DUTY 1” shows in the display. Press the product buttons to set an alarm. 11. Press button and “DUTY 2” shows in the display, and a second alarm can be programmed. 12. Press button and QUAL TMR shows in the display. Press product buttons to set holding time. 13. Press button and “AIF DISABLE” shows in the display and “YES” or “NO”. Using and buttons change the display to “YES” if that product is to not be included in the automatic intermittent filtration operation, or “NO” if it is to be included. 14. Press button and“ASSIGN BTN” shows in the display, along with the product (ex: NUGGETS). If this product already has a product button assigned to it, that LED will be lit. To assign other product buttons to that product, press and hold the product button for 3 seconds and that LED stays lit. To remove a product from a button, press and hold the product button with a lit LED and the LED goes out. 15. To program another product, press X button and ‘SELECT PRODUCT’ shows in display. Continue with step 3 above. 16. Press X button 3 times to end programming. Adding a New Product to the Menu 3-14-08 FM07-284-A

1. Press and hold and buttons until LEVEL - 1 shows in the display, followed by ENTER CODE. 2. Enter code 1, 2, 3, 4. “PRODUCT” and “SELECTN” show in the displays. 3. Press √√√√√ button and ‘SELECT PRODUCT’ and “-P 1-” show in the displays. 4. and buttons scrolls through the 40 products, or press the desired product button 5. Press √√√√√ button and the product shows in the left display and “MODIFY”, and “YES NO” shows in the right display. Press √√√√√ button to change this product, or press X button to choose another product. 6. If √√√√√ button was pressed, use the product buttons to enter product name. Once the desired letter shows in the display, press button to continue to the next letter. 7. Once name is complete, press button and “COOK TIME” shows in the display. Use the product buttons to change the time in minutes and seconds, to a maximum of 59:59. 8. Press button and “TEMP” shows in the display. Press the product buttons to change the temperature. The temperature range is 190°F (88°C) to 380°F (193°C). 9. Press button and “COOK ID” shows in the display. Enter abbreviated product name (Ex: NUG) 10. Press button and “DUTY 1” shows in the display. Press the product buttons to set an alarm. 11. Press button and “DUTY 2” shows in the display, and a second alarm can be programmed. 12. Press button and QUAL TMR shows in the display. Press product buttons to set holding time. 13. Press button and “AIF DISABLE” shows in the display and “YES” or “NO”. Using and buttons change the display to “YES” if that product is to not be included in the automatic intermittent filtration operation, or “NO” if it is to be included. 14. Press button and“ASSIGN BTN” shows in the display, along with the product (ex: NUGGETS). If this product already has a product button assigned to it, that LED will be lit. To assign other product buttons to that product, press and hold the product button for 3 seconds and that LED stays lit. To remove a product from a button, press and hold the product button with a lit LED and the LED goes out. 15. To program another product, press X button and ‘SELECT PRODUCT’ shows in display. Continue with step 3 above. 16. Press X button 3 times to end programming. Adding a New Product to the Menu 3-20-08 FM07-307-A

1. Press and hold and buttons until LEVEL - 1 shows in the display, followed by ENTER CODE. 2. Enter code 1, 2, 3, 4. “PRODUCT” and “SELECTN” show in the displays. 3. Press √√√√√ button and ‘SELECT PRODUCT’ and “-P 1-” show in the displays. 4. and buttons scrolls through the 40 products, or press the desired product button 5. Press √√√√√ button and the product shows in the left display and “MODIFY”, and “YES NO” shows in the right display. Press √√√√√ button to change this product, or press X button to choose another product. 6. If √√√√√ button was pressed, use the product buttons to enter product name. Once the desired letter shows in the display, press button to continue to the next letter. 7. Once name is complete, press button and “COOK TIME” shows in the display. Use the product buttons to change the time in minutes and seconds, to a maximum of 59:59. 8. Press button and “TEMP” shows in the display. Press the product buttons to change the temperature. The temperature range is 190°F (88°C) to 380°F (193°C). 9. Press button and “COOK ID” shows in the display. Enter abbreviated product name (Ex: NUG) 10. Press button and “DUTY 1” shows in the display. Press the product buttons to set an alarm. 11. Press button and “DUTY 2” shows in the display, and a second alarm can be programmed. 12. Press button and QUAL TMR shows in the display. Press product buttons to set holding time. 13. Press button and “AIF DISABLE” shows in the display and “YES” or “NO”. Using and buttons change the display to “YES” if that product is to not be included in the automatic intermittent filtration operation, or “NO” if it is to be included. 14. Press button and“ASSIGN BTN” shows in the display, along with the product (ex: NUGGETS). If this product already has a product button assigned to it, that LED will be lit. To assign other product buttons to that product, press and hold the product button for 3 seconds and that LED stays lit. To remove a product from a button, press and hold the product button with a lit LED and the LED goes out. 15. To program another product, press X button and ‘SELECT PRODUCT’ shows in display. Continue with step 3 above. 16. Press X button 3 times to end programming. Adding a New Product to the Menu 3-31-08 FM07-330-A

1. Press and hold and buttons until LEVEL - 1 shows in the display, followed by ENTER CODE. 2. Enter code 1, 2, 3, 4. “PRODUCT” and “SELECTN” show in the displays. 3. Press √√√√√ button and ‘SELECT PRODUCT’ and “-P 1-” show in the displays. 4. and buttons scrolls through the 40 products, or press the desired product button 5. Press √√√√√ button and the product shows in the left display and “MODIFY”, and “YES NO” shows in the right display. Press √√√√√ button to change this product, or press X button to choose another product. 6. If √√√√√ button was pressed, use the product buttons to enter product name. Once the desired letter shows in the display, press button to continue to the next letter. 7. Once name is complete, press button and “COOK TIME” shows in the display. Use the product buttons to change the time in minutes and seconds, to a maximum of 59:59. 8. Press button and “TEMP” shows in the display. Press the product buttons to change the temperature. The temperature range is 190°F (88°C) to 380°F (193°C). 9. Press button and “COOK ID” shows in the display. Enter abbreviated product name (Ex: NUG) 10. Press button and “DUTY 1” shows in the display. Press the product buttons to set an alarm. 11. Press button and “DUTY 2” shows in the display, and a second alarm can be programmed. 12. Press button and QUAL TMR shows in the display. Press product buttons to set holding time. 13. Press button and “AIF DISABLE” shows in the display and “YES” or “NO”. Using and buttons change the display to “YES” if that product is to not be included in the automatic intermittent filtration operation, or “NO” if it is to be included. 14. Press button and“ASSIGN BTN” shows in the display, along with the product (ex: NUGGETS). If this product already has a product button assigned to it, that LED will be lit. To assign other product buttons to that product, press and hold the product button for 3 seconds and that LED stays lit. To remove a product from a button, press and hold the product button with a lit LED and the LED goes out. 15. To program another product, press X button and ‘SELECT PRODUCT’ shows in display. Continue with step 3 above. 16. Press X button 3 times to end programming. Adding a New Product to the Menu 3-19-08 FM07-296-A