HIKVISION DS-3WF01C-2N Manuals

Installation manual Special Wireless Bridge For Elevator *Please be sure to install and use in pairs. Package Contents: Device of Elevator Room DS-3WF01C-2Nx1; Device of IP Camera DS-3WF01C-2Nx1; DC48V 0.25A POE Adapterx2; Plastic tie x4; Certificate x1; Instructions x1 Device of Elevator Room connection Device of IP Camera connection LAN2 LAN1 12V Reset POE POE Adapter POE POE LAN1/LAN2 LAN POE Adapter The signal level LED Green, yellow and red lights on: the wireless signal level is strong. Yellow and red lights on: the wireless signal level is medium. Red light on: the wireless signal level is weak or no signal. 12V DC power supply port: The default power supply mode is POE, if you want to use 12V DC power supply, you must provide 12V DC Adapter for yourself. Reset Button: User can restore the device to factory settings POE Port: The port used to connect the POE port of POE Adapter, the green LED will light when the port is connected to the POE Adapter. The yellow LED will light when the device connect to the camera or computer successfully. LAN1/LAN2 Port: The Port used to connect camera, information distribution screen and other network equipment Device of Elevator Room Default IP: 192.168.1.35 User name: admin Password: 12345 Device of IP Camera Default IP: 192.168.1.36 User name: admin Password: 12345 Trouble shooting for Network failure, video transmission is not smooth 1.Please confirm that the devices are installed in pairs. The serial numbers of the Elevator Room device and the IP Camera device should be consistent. 2.Make sure the devices are aligned and visible, there is not a bunker between the devices. 3.Make sure the LED and the signal level LED are working properly. Other questions, please contact technical support 400-700-5998 2 1 4 3 6 5 8 7 UPLINK LAN Configuration and Debugging Specification Sheet Marking for the restriction of substances or elements Warranty card Standard Operating Frequency Antenna Output power Receive Sensitivity Max Transmission Rate Power supply Interface Operating Temperature Storage Temperature Operating Humidity Dimensions Application scenarios Encryption Network Mode Security Network Protocol TDMA Auto ACK timing Adjust Management and Logs Web Based Configuration Firmware Update Bandwidth supported IEEE802.11 b/g/n（2T2R 300Mbps） 2400~2500MHz(More Non-standard channels is availability, the range: 2312MHz-2732MHz) Internal, Gain 6dBi, H: 65° V: 60° 27dBm -72dBm@65Mbps, -97dBm@1Mbps 11n: 300Mbps(HT40)/130Mbps(HT20) 11g: 54Mbps 48V PoE or 12V DC 3×10/100M Base-TX (Cat. 5/5E， RJ-45) ports -30℃～+65℃ -40℃～+85℃ 5%～95%RH non-condensing 150*150*31.6mm Elevator Room/IP Camera WPA-PSK/WPA2-PSK Router/Bridge IP/MAC filter, SSID hidden, Interface Isolation TCP/UDP/ARP/ICMP/DHCP/HTTP/NTP Supported (Extend private communication protocol) Supported (It can automatically detect the distances of the devices, keep the performance always the best) NTP，Syslog，Telnet，AC Supported Support update firmware by Web page 20M/40MHz Wireless Items Parameters Hardware Software Explanation Case Printed Circuit Board Power Supply(if exists) Accessory(if exists) x x x x o o o o o o o o o o o o o o o o o o o o Part of the name Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent chromium (CrVI) Polybrominated Biphenyl (PBB) Polybrominated Diphenyl Ethers (PBDE) o indicates that the content of the restricted substance in all homogeneous materials of the part is below the limit specified in the SJ/T11363-2006 standard. x indicates that the content of the restricted substance in at least one of the homogeneous materials of the part exceeds the limit specified in the SJ/T11363-2006 standard. Customer Name： Detailed Address： Telephone： Fax： Postal Code： E-mail： Product Model： Product Number(S/N)： Production Date： YY MM DD Purchase Date： YY MM DD Free Warranty： MM If you have any other requirements, please fill in the following： Dealer： Telephone： Distribution Unit: (Stamp) Mailing Address: Hikvision Technical Service Center, 5 floor of Hikvision Science Park Building 2, No.469 Jianghui Road, Binjiang District, Hangzhou, China Postal Code：310052 Substances or elements which are restricted by Measures for the Control of Pollution from Electronic Information Products

DS-3WF01C-2N Quick Start Guide i DS-3WF01C-2N Quick Start Guide DS-3WF01C-2N Quick Start Guide i Quick Start Guide COPYRIGHT ©2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to DS-3WF01C-2N (Product Series). The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/). Please use this user manual under the guidance of professionals. Trademarks Acknowledgement and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. DS-3WF01C-2N Quick Start Guide ii Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. DS-3WF01C-2N Quick Start Guide iii Applicable Models This manual is applicable to switches below: DS-3WF01C-2N (product series). Symbol Conventions The symbols that may be found in this document are defined as follows.  During the installation and utilization of the device, please strictly conform to electrical safety rules in different nations and regions.  You shall acknowledge that the use of the device with Internet access might be under network security risks, please strengthen protection for your personal information and data security. If you find the device might be under network security risks, please contact with us. Symbol Description Provides additional information to emphasize or supplement important points of the main text. Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.

User Manual of DS-3WF01C-2N DS-3WF01C-2N User Manual User Manual of DS-3WF01C-2N User Manual COPYRIGHT ©2016 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to DS-3WF01C-2N device. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/). Please use this user manual under the guidance of professionals. Trademarks Acknowledgement and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON- INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. User Manual of DS-3WF01C-2N Regulatory Information FCC Information Attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU, the RE Directive 2014/53/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body