HOLOVISION 400-S12-VIK Manuals

Not Used Manual Type 6.2.0.1-RF “Panasonic Compatible” Unit with Essex “S-12 Stand - Alone” Keypad For Models 400-S12-PAN 401-S12-PAN 403-S12-PAN 404-S12-PAN 410-S12-PAN 411-S12-PAN Specifications Communication For use with all Panasonic KSUs with door phone card. This unit is a replacement for the Panasonic KXT-30865 door phone. Access Control Essex “stand-alone” 12 button keypad 1 relay plus 2 grounding outputs (external relays required) 500 users 12 VDC power supply included INSTALLATION INSTRUCTIONS 501 E. Goetz Ave. Santa Ana, Ca 92707 www.eholovision.com Ph. 714-434-6904 Fax 800-362-0002 HOLOVISION 400 Series “S-12” Junction Board 12 VDC input (for camera and keypad) NO, COM, NC relay connections Keypad case ground Remote bypass terminals (activate relay) Connect tamper switch to alarm (optional) Intercom to KSU Cut for NO Contact Closure Loop for Strike Power 12vDC 1.5 A Gate Strike *MOV is recommended NOTE: MOV (metal oxide varistor) is the small red component which is included. Its purpose is to absorb “inductive kick back” which can be created when power is removed from the strike. Loop is required from DC positive to contact common for DC voltage to strike. Essex Keypad Wiring DC Out for Gate Strike Page 2 Type 6.2.0.1-RF CO Line In To Phones KSU Strike 1 Door 1 Cut for NO Contact Closure AC Loop for Strike Remote Bypass Button Essex Keypad Wiring Contact Closure for Gate Operation 12vDC 1.5 A Page 3 Type 6.2.0.1-RF CO Line In To Phones KSU Strike 1 Door 1 Cut for NO Contact Closure AC Loop for Strike Programming the Essex Keypad Note: If the User ID, or User Code/PIN has already been assigned, you will hear one long beep when # is entered. In this case, choose a different User ID / PIN, or see the instructions for changing or deleting codes. DEFAULT USER CODE & MASTER CODE IS “123#” 1 The default Master Code is “123”. This can be changed to a unique code 3 - 8 digits long 2 Enter * 3 1 2 3 # Double Beep Fast Flash Solid 3 Enter 1 # Double Beep Fast Flash Slow Flash 4 Enter new master code, followed by # Triple Beep Fast Flash Solid 5 Enter * * Double Beep 6 EXAMPLE: old code is 123, new code is 456 * 3 1 2 3 # 1 # 4 5 6 # * * Set Master Code STEP ACTION BEEP Red LED Green LED 1 Remove power 2 Jumper the “CONFIG” pins on the rear of the keypad . V = 12 3 Apply 12 VDC power to red and black wires Quadruple Beep Flash Solid 4 Enter 9 9 followed by # Double Beep Flash Solid 5 Enter 2 1 4 followed by # Triple Beep Flash Solid 6 Remove power 7 Remove “CONFIG” jumper 8 Reapply power STEP ACTION BEEP Red LED Green LED Set Keypad Illumination to ON ALL OF THE TIME TYPE 6.2.0.1-RF Page 4

Manual Type 6.2.0.5-RF Viking W-1000 with Essex “S-12 Stand - Alone” Keypad For Models 400-S12-VIK 401-S12-VIK 403-S12-VIK 404-S12-VIK 410-S12-VIK 411-S12-VIK Specifications Communication Viking W-1000 Doorbox uses “half-duplex” communication, allowing for high speaker and microphone volume, without the possibility of feedback Access Control Essex “stand-alone” 12 button keypad 1 relay plus 2 grounding outputs (external relays required) 500 users 12 VDC power supply included INSTALLATION INSTRUCTIONS 501 E. Goetz Ave. Santa Ana, Ca 92707 www.eholovision.com Ph. 714-434-6904 Fax 800-362-0002 HOLOVISION 13.8 VAC (from C-1000B) 12 VDC input (for camera and keypad) NO, COM, NC relay connections Keypad case ground Remote bypass terminals (activate relay) Connect tamper switch to alarm (optional) Intercom to W-1000 ( Not polarity senitive) Cut for NO Contact Closure AC Loop for Strike Cut for NO Contact Closure AC Loop for Strike 12v - 12v + CO line 12vDC 1.5 A TO STANDARD PHONES Gate Strike *MOV is recommended NOTE: MOV (metal oxide varistor) is the small red component which is included. Its purpose is to absorb “inductive kick back” which can be created when power is removed from the strike. Loop is required from 12v positive to contact common for DC power to strike. Essex Keypad Wiring DC Out for Gate Strike Page 2 Type 6.2.0.5-RF NOTE: ‘’Talk Battery’’ switch must be in “ON” position when the C-1000B is used w/o a CO line input. VIKING Model C-1000B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 EARTH GND PHONE LINE INPUT LINE OUT TO PHONES KEYLESS CONTACT DOOR BOX 1 DOOR BOX POWER DOOR BOX 2 DOOR STRIKE 1 DOOR STRIKE 2 1 2 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 OFF ON 13.8 VAC 1.25A Remote Bypass Button 12v - 12v + CO line 12vDC 1.5 A TO STANDARD PHONES Essex Keypad Wiring Contact Closure for Gate Operation Page 3 Type 6.2.0.5-RF NOTE: ‘’Talk Battery’’ switch must be in “ON” position when the C-1000B is used w/o a CO line input. Gate Motor VIKING Model C-1000B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 EARTH GND PHONE LINE INPUT LINE OUT TO PHONES KEYLESS CONTACT DOOR BOX 1 DOOR BOX POWER DOOR BOX 2 DOOR STRIKE 1 DOOR STRIKE 2 1 2 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 OFF ON 13.8 VAC 1.25A Cut for NO Contact Closure AC Loop for Strike Page 4 TYPE 6.2.0.5-RF W-1000 Adjustments and Programming In certain noisy locations (traffic or wind), the microphone volume may need to be decreased. A symptom of this is one-way talk path, in which the distant party cannot be heard over the speaker. A “MIC VOL” adjustment is provided on the doorphone for increasing or decreasing the microphone volume. Microphone Volume The “SPKR VOL” pot can be adjusted to increase or decrease the speaker volume to the desired level. Speaker Volume The maximum number of rings can be adjusted using the DIP switches. Maximum Number of Rings Sw 1 Sw 2 Max Rings OFF OFF 2 ON OFF 3 OFF ON 10 ON ON 30 C-1000B Door Controller Programming 1 Disconnect the PHONE LINE INPUT. 2 Slide the TALK BATTERY switch to the ON position. 3 Move DIP SWITCH 2 from OFF to ON. 4 Connect a phone to terminals 4 & 5 - LINE OUT TO PHONES. 5 Pick up the phone (you will hear a double beep - indicating that you have accessed the PROGRAMMING MODE). 6 You can now Touch Tone program the features listed below. SEE HOLOVISION Programming NOTES. 7 When Finished, hang up and move DIP SWITCH 2 to the OFF position 8 Slide the TALK BATTERY switch back to the OFF position 9 Reconnect line to PHONE LINE OUT Step Action The C-1000 controller is factory set to work right out of the box. If customization of the default settings is required, see the steps listed below. Refer to the C-1000 manual for additional options + + Spkr Vol Mic Vol ON 1 2