Honda 08E10-TK6-100 Manuals

Publications No. Issue Date INSTALLATION INSTRUCTIONS Accessory Application © 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 45980 (1108) 1 of 10 08E10-TK6-1000-91 AII 45980 AMBIENT LIGHTS P/N 08E10-TK6-100 2012 FIT AUG 2011 PARTS LIST 2 Ambient lights 2 Grommets 2 Shims Ambient light harness Template Ambient light switch Narrow wire tie Spacer 6 Wire ties Fuse label Wire tie with clip Aluminum tape TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel Scissors Diagonal cutters File Drill 3.5 mm Drill bit 20 mm Hole saw Pushpin Masking tape Utility knife Eye protection (face shield, safety goggles, etc.) 2 of 10 AII 45980 (1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved. Illustration of the Ambient Lights installed in the vehicle INSTALLATION 1. Make sure you have the anti-theft code for the radio and navigation system (if equipped), then write down the radio presets. 2. Disconnect the negative cable from the battery. 3. Under the dash on the left side of the vehicle, turn the knob of the driver’s dashboard cover counterclockwise. Remove the driver’s dashboard undercover (one clip and two tabs). Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 830401AT FUSE (2A) SWITCH AMBIENT LIGHT AMBIENT LIGHT HARNESS AMBIENT LIGHT 861801AS DRIVER’S DASHBOARD UNDERCOVER CLIP KNOB Turn. 2 TABS 4. Remove the fuse access panel (two clips, five tabs, and two hooks). If equipped with fog lights, unplug the vehicle 5-pin connector and unclip the wire tie. 5. Remove the passenger’s dashboard undercover (three clips and two tabs). 830427AT 2 CLIPS 5 TABS FUSE ACCESS PANEL HOOK VEHICLE 5-PIN CONNECTOR WIRE TIE CLIP HOOK 703102AS PASSENGER’S DASHBOARD UNDERCOVER 3 CLIPS TABS © 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 45980 (1108) 3 of 10 Routing the Ambient Light Harness 6. Using isopropyl alcohol, clean the fuse case where the fuse label will attach. 7. Attach the fuse label (2A AMBIENT LIGHT) to the fuse case on the ambient light harness. 8. Without accessory fog lights: Unplug the vehicle 13-pin connector from the mirror switch, and plug it into the ambient light harness 13-pin connector. Plug the ambient light harness 13-pin connector into the mirror switch. 7D0627AT FUSE CASE Clean. AMBIENT LIGHT HARNESS FUSE LABEL (2A AMBIENT LIGHT) 830416AT VEHICLE 13-PIN CONNECTOR 2 AMBIENT LIGHT HARNESS 13-PIN CONNECTORS AMBIENT LIGHT HARNESS MIRROR SWITCH 9. With accessory fog lights: Unplug the vehicle 13-pin connector from the fog light harness, and plug it into the ambient light harness 13-pin connector. Plug the other ambient light harness 13-pin connector into the fog light harness 13-pin connector. 10. Secure the 13-pin connector. Without Fog Lights: Using one wire tie, secure the excess ambient light harness and connector to the vehicle harness. With Fog Lights: Secure the two 13-pin connectors to the fog light harness using one wire tie for each connector. 830417BT AMBIENT LIGHT HARNESS 13-PIN CONNECTORS FOG LIGHT HARNESS 13-PIN CONNECTOR VEHICLE 13-PIN CONNECTOR MIRROR SWITCH 830418BT AMBIENT LIGHT HARNESS VEHICLE HARNESS WIRE TIE FOG LIGHT HARNESS WIRE TIE AMBIENT LIGHT HARNESS 13-PIN CONNECTORS 4 of 10 AII 45980 (1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved. 11. Using one wire tie, secure the ambient light harness to the square hole in the vehicle frame (If another accessory harness is installed, secure the ambient light harness to the other accessory harness). 12. Using one wire tie, secure the ambient light harness to the vehicle frame. 13. Using one narrow wire tie, secure the ambient light harness to the square hole in the vehicle frame (If another accessory harness is installed, secure the ambient light harness to the other accessory harness). 830419BT SQUARE HOLE AMBIENT LIGHT HARNESS With other accessory harness HARNESS NARROW WIRE TIE NARROW WIRE TIE SQUARE HOLE WIRE TIE WIRE TIE HARNESS WIRE TIE With other accessory harness VEHICLE FRAME WIRE TIE NARROW WIRE TIE 14. Secure the ambient light harness to the square hole in the pocket with one wire tie (If another accessory harness is installed, secure the ambient light harness to the other accessory harness). 15. Using one wire tie, secure the ambient light harness to the OBD-II connector harness. 16. Using one wire tie, secure the ambient light harness (at the second green tape) to the oval hole in the metal frame. Do not secure the harness to the plastic frame, otherwise the lower cover cannot be reinstalled. 830420AT WIRE TIE FIRST GREEN TAPE With other accessory harness SQUARE HOLE OBD-II CONNECTOR AMBIENT LIGHT HARNESS VEHICLE HARNESS WIRE TIE SQUARE HOLE 830421AT WIRE TIE SECOND GREEN TAPE AMBIENT LIGHT HARNESS METAL FRAME BACK VIEW WIRE TIE METAL FRAME PLASTIC FRAME