Honeywell HD4MDIP Manuals

Document 800-05621 – Rev A – 02/10 Document 800-05621 – Rev A – 02/10 EQUIPTM Series High Definition (720p) True Day/Night IP Dome Camera Quick Install Guide Introduction Thank you for purchasing a Honeywell HD4 EQUIP Series IP Dome Camera. Before installing your camera, please verify your model and read this guide carefully. For detailed information for your specific camera, please refer to the appropriate user guide located on the IP Utility CD. When you install the Honeywell IP Utility software, the User Guide will automatically be downloaded to your computer. Before installing the camera, Honeywell recommends that you go to www.honeywellvideo.com/ products/cameras/index.html and look under Indoor/Outdoor Mini-domes to find your camera, then download the latest manuals and software updates. Preparation Black tabs (x4) Black clips (x4) Metal hinge Mounting holes Gimbal Dome bubble Turret Removing the Dome Bubble and Turret 1. Using the supplied Allen key, loosen the captive screws on the dome bubble. Remove the dome bubble and set it aside. 2. Gently pull the turret off the gimbal, then set it aside. Removing the Gimbal Remove the gimbal from the enclosure base so you can easily access the mounting holes (see illustration). 1. Squeeze the 4 black tabs until they are free of the black clips. 2. Elevate the hinge until the gimbal is above the housing and you have access to the enclosure base mounting holes. Caution When elevating the hinge, do not overstress the two ribbon cables. If necessary, rotate the gimbal to provide additional slack. Camera Installation 2 Mounting the Camera 1. Route the cables through your chosen conduit entry. 2. Mount the camera to a wall or ceiling using the supplied screws. Note To prevent moisture from entering the housing, ensure that the gasket is flush against the back of the camera enclosure and is not pinched. Connecting the Wiring 1. Connect the power input: • For 24 VAC connection, locate the two-pin green connector that was shipped with your camera and make the necessary connections. • For PoE connection, connect a CAT5 cable to the RJ45 network connector. Power: 24 VAC RJ45 Ethernet network connection Audio/Alarms Local video out (adjusting and focusing) 2. Connect the alarms and audio: Locate the eight-pin green connector that was shipped with your camera and make all the necessary connections as shown in the table below. 3. Connect to the network: If you haven’t already connected a CAT5 cable to the RJ45 network connector for PoE, then connect a CAT5 cable to the RJ45 network connector. Note For detailed audio and alarm configuration information, refer to the Refence Guide for your camera located on the IP Utility CD. Sealing the Wiring To prevent moisture from entering the housing, if you are using the back conduit entry, apply sealant around the conduit connection and the mounting screws. Adjusting the Camera 1. Verify that power is applied to the camera. Note Please allow the camera to initialize before proceeding. Video output is not instantaneous with the application of power. 2. Reinstall the gimbal by inserting the black tabs into the black clips on the enclosure base. 3. Connect the supplied video cable to the local video out connector to view the video signal on a standard monitor (see illustration below for local video out connector location). 4. Loosen the setscrew that locks the gimbal assembly in place to adjust the horizontal rotation. 5. Follow the legend below to adjust the camera (pan, tilt, and focus) to the desired view. 6. Retighten the setscrew to lock the gimbal assembly in place. 7. Disconnect the supplied video cable. Reinstalling the Turret and the Dome Bubble 1. Align the turret on the gimbal, then gently press until the turret clicks securely into place. 2. Align the dome bubble captive screws with the mounting holes in the enclosure base, then securely screw them into place. In Out Audio Alarm In Out 24 VAC 1 2 3 4 5 6 7 8 PIN Definition 1 Audio In + 2 Audio In – 3 Audio Out + 4 Audio Out – 5 Alarm In + 6 Alarm In – 7 Alarm Out + 8 Alarm Out – Legend A = Tilt rotation B = Horizontal rotation C = Pan rotation B C A Setscrew (loosen to adjust horizontal rotation) Set focus (top) Set focal length (bottom) Top View Loosen locking screw (inside conduit entry) to remove the side conduit plug Reset button Local video out 1 Preparing the Mounting Surface 1. Use the mounting template to mark the mounting surface for the screw holes and the cable access hole. Note To prevent moisture from entering the housing, position the enclosure with the side conduit entry pointing down. 2. Pre-drill holes in the mounting surface as required. Installing the Conduit Plug The HD4MDIP/X ships with the conduit plug pre-installed in the enclosure base back conduit entry. To use the back conduit entry, remove the conduit plug and install it in the side conduit entry after loosening the locking screw. (See Top View in Adjusting the Camera in Camera Installation.) Retighten the locking screw to secure the conduit plug in place. Note For secure installations, protect surface-mounted cables with plastic or metal cable covers. Installing the Grommet (optional) If a conduit is not used for cable routing, install the rubber grommet in the conduit hole (onto the camera base), then slit the grommet and feed the cables through. Use the appropriate sealant to seal the grommet to prevent moisture from entering the housing. Side conduit entry Back conduit entry Enclosure base Conduit plug locking screw Conduit plug Please turn over

Honeywell’s latest addition to the EQUIP® Series of IP-based products, the HD4MDIP is a high definition, True Day/Night rugged indoor/outdoor fixed mini-dome camera. This ultra compact and vandal-resistant camera provides extremely crisp images at minimal bandwidth. The HD4MDIP provides 720p resolution at full frame rate. Progressive scan technology and 2D edge enhancement provide outstanding clarity and definition. Digital Noise Reduction results in significant storage savings without sacrificing image quality in low light. The ¼" progressive scan CMOS sensor offers the latest in digital video surveillance technology with accurate color rendition through a wide variety of lighting conditions. The HD4MDIP integrates a camera and lens in an ultra compact, single piece, tamper proof unit for fast and easy installation in any application. The camera comes complete with surface and flush mounting options (compatible with a 4S electrical box), and optional wall and pendant mount kits are available. In addition to the low light color performance, the camera will automatically switch to black and white. In this mode, lighting can be complemented with infrared for discreet/covert low light surveillance with exceptional monochrome images. A 3-D axis gimbal capable of 360° of pan, 180° of tilt and 360° of horizontal rotation simplifies mechanical camera adjustment. The Vari-focal Auto Iris lens allows the field of view to be adjusted to suit the scene requirements, and an on-board analog output allows the installer to connect a local test monitor while adjusting the scene. A powerful and intuitive web client allows fine tuning of the camera. This can also be performed from most DVR/NVR setup utilities. The HD4MDIP supports dual video streams and multiple compression formats with rates up to 30 frames per second (25 fps for PAL systems). The digital compression parameters for the two video streams are independently configurable. A third analog stream can be utilized for failover and local viewing, and is also valuable when retrofitting onto an existing analog input DVR or encoder (full resolution not available). With built-in low current Power over Ethernet (IEEE 802.3af), Class 1, power is supplied to the camera using standard network cabling, eliminating the need for a separate power supply and associated wiring. In retrofit situations where PoE switching does not exist, the unit can also be powered directly from 24 VAC. Market Opportunities The HD4MDIP is perfect for installations where excellent picture clarity at minimal bandwidth is required. At three times the resolution of standard analog cameras, yet with similar bandwidth requirements, the HD4MDIP can be retrofitted on many existing DVR/NVR installations without requiring additional storage. Its discreet, vandal-resistant, outdoor design provides maximum protection against dust, dirt, and water, and is also impact resistant. This provides optimum performance for both indoor and outdoor applications. Features www.honeywellvideo.com HD4MDIP • Outstanding image quality, 720p (1280 X 720) resolution • 30 fps (25 fps PAL) progressive scan • True Day/Night, 3.3-12 mm VFAI lens with removable IR cut filter • Camera tamper detection • Video motion detection • Wall and pendant mount kit available • Selectable compression formats • Dual digital video streams simultaneously, independently configurable • Remote firmware update • Supports both dynamic and static IP address assignment • Includes advanced IP locator software to make system setup easy • Web server for remote setup of camera video and network parameters • Choice of 24 VAC or PoE IEEE 802.3af class 1 power inputs • Supports input and output alarm contacts • Supports bidirectional audio • Rugged polycarbonate dome EQUIP® SERIES 720P TRUE DAY/NIGHT RUGGED INDOOR/OUTDOOR DOME NETWORK CAMERA

Document 800-07091 – Rev A – 07/10 User Guide HD4 EQUIP™ Series True Day/Night Rugged IP Network Camera NTSC / PAL HD4VDIP HD4VDIPX HD4MDIP HD4MDIPX