Horizon Fitness Andes 2 Manuals

Rev. 1.0 | 020909’ FOR MODEL: Andes 2 Andes 3 02/09/09 3:31:08 PM ASSEMBLY IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE! There are several areas during the assembly process of an elliptical that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken. WARNING 1 2 UNPACKING Unpack the product where you will be using it. Place the product on a level flat surface. It is recommended that you place a protective covering on your floor. During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended. TOOLS INCLUDED 5mm Allen Wrench 4mm Allen Wrench 13/15mm Flat Wrench 17mm Flat Wrench PARTS INCLUDED HANDLE PULSE BOTTLE HOLDER CONSOLE MAST CONSOLE MAST BOOT PEDAL ROLLER WHEEL COVERS GUIDE RAIL UPPER HANDLEBAR HANDLEBAR COVERS CONSOLE MAST BOOT LOWER HANDLEBAR STABILIZER TUBE HANDLEBAR COVER TRANSPORT WHEEL PEDAL ARM CONSOLE Phillips Screw Driver 1 Main Frame Set 2 Upper Handlerbars 2 Lower Handlerbars 2 Pedal arms 2 Guide Rails 1 Console 1 Console Mast 1 Console Mast Boot 1 Power Supply 2 Crank Boots 2 Front Upper Handlebar Covers 2 Back Upper Handlebar Covers 6 Hardware Pack (contents listed below) 821E_Rev.1.1.indd 4-5 02/09/09 3:57:03 PM HARDWARE BAG FOR STEP 1 CONTENTS : HARDWARE BAG FOR STEP 2 CONTENTS : 3 4 ASSEMBLY STEP 1 A) Open HARDWARE BAG FOR STEP 1. B) Attach the washer (A) to the tube (D),and then attach the transport wheel to the stabilizer tube (E) using washer(B), screw(C). C) Repeat on the other side. ASSEMBLY STEP 2 A) Open HARDWARE BAG FOR STEP 2. B) Slide left and right GUIDE RAILS into MAIN FRAME. C) Attach GUIDE RAILS using 2 BOLTS (A). NOTE: You may have to rotate the guide rails back and forth to get them to slide into the frame. BOLT (A) M8x1.25Px70L Qty: 1 NUT (E) Nylon Nut M8x1.25P Qty: 1 SPRING WASHER (C) Qty: 3 ARC WASHER (D) Qty: 5 BOLT (B) M8x1.25Px15L Qty: 3 ASSEMBLY STEP 3 HARDWARE BAG FOR STEP 3 CONTENTS : A) Open HARDWARE BAG FOR STEP 3. B) Slide the CONSOLE MAST BOOT over the bottom of the CONSOLE MAST. C) Carefully pull console wires through the CONSOLE MAST. Attach the CONSOLE WIRES to the pre-attached routing wire. Discard wire when finished. D) Slide CONSOLE MAST into MAIN FRAME. E) Insert 3 BOLTS (B), 3 SPRING WASHERS (C) and 3 ARC WASHERS (D) into back of CONSOLE MAST. F) Attach CONSOLE MAST to MAIN FRAME using 1 BOLT(A),2 ARC WASHER(D),1 NUT(E). G) Slide CONSOLE MAST BOOT down to cover exposed bolts. Qty:2 M8x1.25Px15L BOLT(A) BOLT(A) 8.2x 13.5x2.0t 8.4x 17.0x1.0t TRANSPORT WHEEL MAIN FRAME BOLT (B) SPRING WASHER (C) MAIN FRAME BOLT (A) ARC WASHER (D) ARC WASHER (D) NUT (E) GUIDE RAILS ASSEMBLY STEP 4 PRE-ATTACHED A).Open the box with pedal and pedal arm inside. B) Open the hardware bag for the step 6. C) Remove the pre-attached srews and washers from the bottom of the pedal base,then put the pedal onto the pedal base using these screws and washers. D) Repeat on the other side. CONSOLE WIRE (A) (B) (D) (E) (C) waher (A) 16.0x 25x1.5T Qty:2 washer(B) 5/16’x 30.0x1.5T Qty:2 screw(C) M8x1.25Px12L Qty:2

FOR MODEL : Andes 2 Andes 3 ELLIPTICAL USER’S GUIDE 821E_Rev.1.1.indd 1 2/09/09 08:55:02 AM 3 INTRODUCTION TABLE OF CONTENTS Important Precautions Before You Begin Elliptical Operation Conditioning Guidelines Troubleshooting & Maintenance 4 5 7 Folding/Unfolding 6 16 21 25 CONGRATULATIONS and THANK YOU for your purchase of this Horizon Fitness elliptical! Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, an Horizon Fitness elliptical- can help you attain it – adding club-quality performance to your at-home workouts, with the ergonomics and innovative features you need to get stronger and healthier, faster. Because we're committed to designing fitness equipment from the inside out, we use only the highest quality components. It's a commitment we back with one of the strongest frame-to-brake warranty packages in the industry.You want exercise equip- ment that offers the most comfort, the best reliability and the highest quality in its class. Horizon Fitness delivers. Exclusions And Limitations (Andes 2) (Andes 3) 2 4 5 SAVE THESE INSTRUCTIONS Read all instructions before using this elliptical. When using an electrical product, basic precautions should always be followed. It is the responsibility of the owner to ensure that all users of this elliptical are adequately informed of all warnings and precautions. If you have any questions after reading this manual, contact Customer Tech Support at the number listed on the back panel of this manual. IMPORTANT PRECAUTIONS WARNING To reduce the risk of burns, fire, electrical shock or injury to persons: • If you experience chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your physician before continuing. • Maintain a comfortable pace. Do not sprint above 80 rpms on this machine. • To maintain balance, it is recommended to keep a grip on the handlebars while exercising, mounting or dismounting the machine. • Do not wear clothes that might catch on any part of the elliptical. • Do not turn pedal arms by hand. • Make sure handlebars are secure before each use. • Do not insert or drop any object into any opening. • Unplug elliptical before moving or cleaning it. To clean, wipe surfaces down with soap and slightly damp cloth only; never use solvents. (See MAINTENANCE) • This elliptical should not be used by persons weighing more than 250 pounds. Failure to comply will void the warranty. • This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional setting. Failure to comply will void the warranty. • Do not use elliptical in any location that is not temperature controlled such as but not limited to: garages, porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply may void the warranty. • Use the elliptical only as described in this manual. • Keep the topside of the foot support clean and dry • Care should be taken when mounting or dismounting the equipment. Before mounting or dismounting, move the pedal on the mounting or dismounting side to its lowest position and bring the machine to a complete stop. • Disconnect all power before servicing the equipment. At NO time should pets or children under the age of 12 be closer to the elliptical than 10 feet. At NO time should children under the age of 12 use the elliptical. Children over the age of 12 should not use the elliptical without adult supervision. It is essential that your elliptical is used only indoors, in a climate controlled room. If your elliptical has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the elliptical is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure. BEFORE YOU BEGIN CONGRATULATIONS on choosing your elliptical. You’ve taken an important step in developing and sustaining an exercise program! Your elliptical is a tremendously effective tool for achieving your personal fitness goals. Regular use of your elliptical can improve the quality of your life in so many ways. HERE ARE JUST A FEWOF THE HEALTHBENEFITS OF EXERCISE: • Weight Loss • A Healthier Heart • Improved Muscle Tone • Increased Daily Energy Levels The key to reaping these benefits is to develop an exercise habit. Your new elliptical will help you eliminate obstacles that prevent you from exercising. Inclement weather and darkness won't interfere with your workout when you use your elliptical in the comfort of your home. This guide provides you with basic information for using and enjoying your new machine. LOCATION OF THE ELLIPTICAL Place the elliptical on a level surface. There should be 6 feet of clearance behind the elliptical, 3 feet on each side and one foot in front for the power cord (See diagram to the right). Do not place the elliptical in any area that will block any vent or air openings. The elliptical should not be located in a garage, covered patio, near water or outdoors. 6 7 FOLDING YOUR ELLIPTICAL TRAINER Note: It is important to always follow the correct order of steps when folding your elliptical trainer. STEP 2: Carefully raise both the pedal arm (in the backmost position) and guide rail simultaneously. STEP 4: Repeat process for alternate side. Note: It is important to always follow the correct order of steps when unfolding your elliptical trainer. STEP 2: Repeat process for alternate side. UNFOLDING YOUR ELLIPTICAL TRAINER POWER Do not operate the elliptical if the power cord or plug is damaged. If the elliptical appears not to be working properly, do not use the elliptical. MOVING Our ellipticals are well built and heavy, weighing up to 200 lbs! Use care when moving and get additional help if necessary. ELLIPTICAL OPERATION WARNING WARNING STEP 1:Firmly grasp both the left pedal arm and guide rail. Press and release the lock latch receiv-er from the lock latch. Carefully lower the pedal arm and guide rail, standing to the side to avoidany accidental release of the alternate pedal arm and guide rail. STEP 1:The first step is to position the elliptical pedal arms in the proper position. The pedal armscan be positioned in two different positions for convenience. The first position is to rotate the leftpedal arm so that it is in the backmost position (the left pedal arm wheel should be positioned at therear of the elliptical trainer). The second position would be to rotate the right pedal arm in the back-most position. STEP 3:Press and hold the lock latch button located underneath the guide rail end cap.Align thelock latch with the lock latch receiver located underneath the pedal arm.Insert the lock latch receiv-er into the lock latch.Release the lock latch button once the lock latch is secure. Your programmable elliptical is powered by a power supply. The power cord must be plugged into the power jack, which is located in the front of the machine near the STABILIZER TUBE.