Hotron SSR-3 Manuals

50mm 50mm ① Attach the mounting template so that its bottom edge is flush with the bottom edge of the door engine cover. Sensor’s Cable Cable Red Black White Green Yellow(+) Gray(+) Activation Output AC/DC 12 to 24 [V] ±10% Safety Output Collector Emitter N.O. COM Power （Non Pole） Test Input Test-P Test-N Set “Test input” dip switch setting 6 to “ON” Ref section 7, Dip Switch Settings. Y ON 6 SSR-3 User Manual (Original) COMPLIED STANDARDS DIN18650-1:2005 EN 12978:2003 +A1:2009 EN 16005:2012 EC type examination 44 205 12 414283-001 English Installation Instruction Accessories Mounting Template Cable Mounting Screws (2 pcs.) 1. DESCRIPTION Door OFF ON ☆ = Default Setting When more than two sensors are installed in close proximity to each other select different frequency settings for each sensor to prevent cross interference. Doorway Learn 2. DIMENSIONS 3. LED INDICATORS 6. MOUNTING & WIRING INFORMATION 7. DIP SWITCH SETTINGS Description The sensor will detect a stationary object for the preset presence timer setting on the inner 3 rows. Possible Setting Options Function IR. Presence Timer IR. Frequency Doorway Learn allows the 1st row of detection to be focused inside the door close area without the detecting door movement. X Dip Switch Dip Switch Disregarding this symbol may result in serious injury or death Note Special attention is required when this symbol is shown ② Drill mounting (3.5mmφ) and wiring (10mmφ) holes. Drilling may cause electric shock. Be careful of hidden wires inside the door engine cover. Note Setting required to conform with EN16005 ⑤-1 Wiring to a door controller that can test the sensor ⑤-2 Wiring to a door controller that cannot test the sensor OFF Note X Y Set “Test input” dip switch setting 6 to “OFF” Ref section 7, Dip Switch Settings. Y Note WARNING ! CAUTION ! Disregarding this symbol may result in injury or damage to equipment 3.2m (10.5ft) A B Mounting height of 3.2m (10.5ft) or lower Mount within 50mm of the bottom of the door engine cover Ensure there are no moving objects in the detection zone Use different frequency settings for sensors in close proximity Ensure the minimum of reflected sunlight from the floor 4. MOUNTING PRECAUTIONS Ensure no condensation gets onto the sensor. If possible ensure no accumulation of snow or water on the floor. If the sensor is exposed to excessive rain install with a Hotron weather cover WARNING ! Sensor’s Cable Cable Red Black White Green Yellow(+) Blue(-) Gray(+) Activation Output AC/DC 12 to 24 [V] ±10% Safety Output Collector Emitter N.O. COM Power （Non Pole） ON 6 OFF Y do not connect do not connect ⑦ Replace Cover. ⑥ House connectors in the space provided. CAUTION ! Blue(-) Brown(-) Brown(-) 2s ☆ 1 2 30s 1 2 1 2 1 2 60s ∞ A ☆ 3 4 B 3 4 3 4 3 4 C D 5 5 Door ☆ When Doorway Learn is turned ON, the sensitivity level of the inner row of detection is only at maximum when the outer rows of detection are activated Safety Relay Output N.O. N.C. ☆ Monitor Mode Door Hold Refer to [11.Timing Chart of events] for full details on Safety Output When connected to a door controller without a TEST input, set to “OFF”. When connected to a door controller with a TEST input, set to “ON” Refer to [11.Timing Chart of events]. When set to ON, pedestrians moving away from the sensor will not be detected. Test Input Setting from Door Controller Reflection Diagnostics Set to snow in instances where false door activations can result from blowing snow, leaves or rubbish in the door close area. Safety Output (Opto-Coupler) Transmitter Receiver IR Spot Receiver IR Spot Transmitter LED ☆30s 1 2 A ☆ 3 4 OFF 5 ☆ To comply with EN16005 set the presence timer to 30s or more Direction Detection RADAR Description Possible Setting Options Function ON 1 1 OFF ☆ ON ☆ 6 6 N.O. ☆ Set to “ON” to comply with EN16005 OFF ON ☆ 6 6 OFF ☆ A low reflected infrared signal is indicated by a slow flashing Red/Green LED. To ignore this low reflection error state, set this dip switch to “Low Reflection”(ON). To comply with EN16005 set to “Normal” Low Ref. 7 7 Normal ☆ 7 Normal ☆ Snow 5 5 Normal ☆ 5 Normal ☆ Switch to OPEN to hold the door in the open position CAUTION ! Open 4 4 Auto ☆ 4 Auto ☆ Dip Switch Y 0v ON Without TEST With TEST Without TEST 0v OFF Radar sensor unit Potentiometer (IR. Sensitivity Volume) Potentiometer (Radar Sensitivity Volume) Connector IR. sensor unit Depth Adjustment Screw(IR. Area) Dip Switch X Dip Switch Y 75mm(2.95") = Standard Mounting Pitch 25mm (0.98") 15mm (0.59") 35mm (1.37") 10mm (0.39") 265mm (10.43") 43mm (1.69") 60mm (2.36") Green Standby Green blinking Doorway Learning (When dip switch Y 5 is ON) Blue RADAR Detecting Red IR. Detecting / RADAR and IR. Detecting Orange Detection row “ROW1”(“ROW2” when doorway Learning is turned ON) is detecting door movement Orange blinking (Fast) Indicates a change of dip switch settings Orange blinking (Slow) Door Hold is turned ON (When dip switch Y 4 is ON) Green/Red blinking (Fast) Internal Sensor Error Green/Red blinking (Slow) Reflected infrared signal from the floor is very low Max 50mm A B Side View A B Plan View Moving Door Leaf Moving Door Leaf To maximize the effectiveness of doorway detection, install the SSR-3 outside and inside as shown below. 5. TECHNICAL SPECIFICATIONS 0.56 [lb.] (0.26 [kg]) Cable , Mounting Screw 2pcs., Mounting Template, Installation Instruction -20 to +60 [Deg.C],(-4 to 140 Deg.F) Below 80% Model Name SSR-3 Installation Height 3.2[m] (10.5 [ft]) Max, 　EN16005 Conformity = 3m Weight Accessories Black, Silver Operating Temperature Operating humidity Supply Voltage AC/DC 12 to 24 [V] ±10% 50/60Hz Power Consumption AC12V-2.5 [VA] (Max) AC24V-2.5 [VA] (Max) DC12V-150 [mA] (Max) DC24V-80 [mA] (Max) Color Category 2 , performance level D according to EN ISO 13849-1:2008 IP Rate IP54 Common Specification Specifications of Reflection Sensor Open collector: 7.5 [mA] (Max) Resistor Load Opto coupler (NPN) Voltage: 55 [VDC] Max. Current : 50 [mA] Max. Dark Current: 100 [nA] Max. (Resistance load) Form A Relay DC50 [V] 0.1[A] Resistor Load 6 [mA] Max. @ 24 [VDC] Output Test Input IR. RADAR Active Infrared Reflective Detection Method Output Holding Time Presence Timer 2, 30, 60 [seconds] or ∞ 0.1 ～ 0.2 [seconds] Response Time 0.5 [seconds] App. Specifications of Redar Sensor Detection Method 1.5 [seconds] App. Output Holding Time 0.1 ～ 0.2 [seconds] Response Time Transmit frequency 24.15 [GHz] Doppler method: ( moving body detection) Notice: Specification may be changed without prior notice. ※Removing the cover after installation ③ Remove the sensor cover as illustrated ④ Attach the sensor with the mounting screws provided ① Push ① Push ② Pull Flat screwdriver ② Pull Dip Switch Y 1 N.O. N.C. ☆ 2 Activation Output (Mechanical Relay) N.O. N.C. ☆ Refer to [11.Timing Chart of events] for full details on Activation Output 2 N.O. ☆ Activation Relay Output Flat screwdriver Slit in base Lift the sensor from its cover The Radar part of the SSR-3 sensor may be negatively influenced by metal close to or in the detection field Area Mask 8.DETECTION AREA WIDTH AND DEPTH ADJUSTMENT Detection Area Depth Adjustment: IR. (Inner 3 Rows) CAUTION ! The above illustrated detection areas represent the actual position of the infrared and radar beams. The actual detection area observed will vary depending on the sensor installation environment, objects been detected and sensor settings. Please ensure that the detection area is set to conform to EN16005. Adjustment screw Detection Area Depth Adjustment: RADAR (Outer) Detection Area Width Adjustment: IR. (Inner 3 Rows) Narrow 3.2 1.0 2.0 3.0 [m] 2.2 2.0 1.0 0 1.0 2.0 Wide 【 Near 】 0 1.0 0.5 [m] 2.2 2.0 1.0 3.0 3.2 [-8 degree] setting Door 【 Far 】 [m] 1.0 0 2.2 Door 2.0 1.0 3.0 0.5 3.2 [4 degree] setting Radar sensor unit Far Near Far Near OR 3 OFF ☆ Activation Relay Output Configuration Choose how relay output is configured. ON 3 3 OFF ☆ RADAR RADAR + IR rows 2+3 ※　Detection area varies depending on walking speed ※　Adjustment possible in 3 ° steps as illustrated Put on Separation Mounting Screws (2 pcs.) Area Mask ON 1 2 3 4 5 6 7 ON 1 2 3 4 5 6 [15 degree] setting [30 degree] setting [45 degree] setting 1.0 0 1.0 [m] 2.0 2.0 2.0 1.0 3.0 1.0 0 1.0 [m] 2.0 2.0 2.0 1.0 3.0 Installation height "2.2m" and Sensitivity set to "High". Installation height "2.2m" and Sensitivity set to "Low". Cover Indicator LED (Red, Green & Blue) IR. Detection Window Radar Detection Window EN16005 EN16005 EN16005 EN16005 EN16005 EN16005 Verify that the detection area position conforms to EN16005 by using the Hotron Beam Finder

H4ftsTRON __,_ C E: © SSR-3 U ser Man ual 1. DESCRIPTION Cover COMPLIED STANDARDS DIN18650-l:2005 EN 12978:2003 +Al:2009 EN 16005:2012 EC type examination 44 205 12 414283-001 Accessories ARNING Disregarding this . symbol may result m serieus injwy or death & Disregarding this symbol may AUTION result in injury or damage to equipment Special attention is required when this symbol is shown llmllll 2. DIMENSIONS 75mm(2.95") = Standard Mounting Pitch 25mm 15mm 35mm 10mm (0.98")(0.59''.) (1.37") (0.39") Setting required to conform with ENl6005 ]Ȣ \ J Mounting Template rtltf➔--1 ; :r:t t. ______ r::_; 0] (Red, Green & Blue) Potentiometer \ Radar Detection Window IR. Detection Window Potentiometer lnstallation lnstruction (IR. Sensitivity Volume) (Radar Sensitivity Volume) Cable Connector ȣ Area Mask Mounting Screws (2 pcs.) Dip Switch(f) IR. sensor unit Radar sensor unit Depth Adjustment ITID Screw(IR. Area) 4. MOUNTING PRECAUTIONS Mounting height of 3.2m (10.5ft) or lower rfflr32m ȤO.Sft) Mount within 50mm of the bottom of the door engine cover ( Ensure there are no moving objects in the detection zone If the sensor is exposed lf possible ensure no to excessive rain install accumulation of snow or with a Hotron weather water on the floor. Ensure the minimum of reflected sunlight from the floor covȥ r w · · ···-Ȧ  1ill ·es To maximize the effectiveness of doorway detection, install the SSR-3 outside aud inside as shown below. · Moving Door Leaf I Moving Door Leaf Plau View 6. MOUNTING & WIRING INFORMATION JARMNG Drilling may cause electric shock. Be careful of bidden wires inside the door engine cover. Area Mask Ensure no condensation gets onto the sensor. Use different frequency settings for sensors in close proximity The Radar part of the SSR-3 sensor may be negatively influenced by metal close to or in the detection field ....._ ___ _,u..-•,•,•sm•m ll•0.•43•")--'-----I !mmt161 3. LED INDICATORS Green Green blinking Blue Red Orauge Staudby Doorway Learning (When dip switch Q'.) 5 is ON) RADAR Detecting IR. Detecting / RADAR and IR. Detecting Orange blinking (Fast) Orauge blinking (Slow) Green/Red blinking (Fast) Green/Red blinking (Slow) Detection row "ROW 1 " ( "ROW2" when doorway Learning is turned ON) is detecting door movement lndicates a chauge of dip switch settings Door Hold is tumed ON (When dip switch Y@is ON) Internal Sensor Error Reflected infrared signa! from the floor is very low 5. TECHNICAL SPECIFICATIONS Common Specification Model Name SSR-3 Installation Height 3.2[m] (10.5 [ft]) Max, EN16005 Confonnity- 3m Supply Voltage AC/DC 12 to 24 [VJ ±10% 50/60Hz Power Consumption AC12V-2.5 [VA] (Max) AC24V-2.5 [VA] (Max) DClZV-150 [mA] (Max) DC24V-80 [mA] (Max) Opto Relay Non Pole Output IR. Voltage: 48 [VDC] Max. Current 300 [mA] Max. (Resistance laad) RADAR Form A Relay DC50 [VJ O. l[A] ResistorLoad Test Input 6 [mA] Max. @24 [VDC] Operating Temperature -20 to +60 [Deg.C],(-4 to 140 Deg.F) Operating humidity Below 80% IP Rate IP54 Category 2 , performance level D according to EN ISO 13849-1 :2008 Weight 0.56 [lb.] (0.26 [kg]) Color Black, Silver Accessories Cable , Mounting Screw 2pcs., Mounting Template, Installation Instruction Specifications of Reflection Sensor Detection Method Active Infrared Reflective Output Holding Time 0.5 [seconds] App. Response Time 0.1 ~ 0.2 [seconds] Presence Timer 2, 30, 60 lseconds or oo Specifications of Redar Sensor Detection Method Doppler method: ( moving body detection) Transmit frequency 24.15 [GHz] Output Holding Time 1.5 [seconds] App. Response Time 0.1 ~ 0.2 [seconds] Notice: Specification may be changed without prior notice. Q) Attach the mounting template so that its bottom edge is flush with the bottom edge of the door engine cover. ® Drill mounting ( 3.5mm rJ,) and wiring ( 10mm rJ,) holes. CT) Remove the sensor cover as illustrated @ Attach the sensor with the mounting screws provided @-1 Wiring to a door controller that can test the sensor Ȫesȫdip switchO]<:J setting®6 to "ON" Refsection 7, Dip Switch OFF n Settings. g ® ON 6 Red - Black - White = Green - Yellow = Blue - Gray(+) - Brown(-) - 0--AC·DC ] Power 12 10 24 [VJ (Non Pole) 0--:rl0°o J N.O. COM J Activation Output J Opto Relay J Safety Output 3Test-P Test-N ]rest Input @ House connectors in the space provided. (J) Replace Cover.  Lift the sensor fro Ȭ') ȭ"· Ȯ Iat screwdriver Slit in base @-2 Wiring to a door controller that cannot test the sensor ȯest input" dip switch rn <:J setting Q'.) 6 to "OFF" Re/ section 7, Dip Switch Settings. OFFa ONLJ ® 6 Red - Black - White = Green - Yellow = Blue - Gray(+) ..... Brown(•) - o--Acme j Power 12 to 24 [VJ (Non Pole) 0--±10"• J N.0. COM ]Activation Output JOpto Relay ]safety Output o- do not connect o- do not connect ,S:,Removmg the cover after mstallanon G) Push 2\, G1J Pull Ȱ Jl'Flat screwdnver  G)Push../ 7. DIP SWITCH SETTINGS li YYYI li YYY1 * - Default Setting Dip Switchȧ Dip Switch (X) Function Dip Switch@ Description Possible Setting Options IR. *30swH The sensor will detect a stationary object for the preset presence timer 2sHH *30swH 60sH w 00ĠĠ [] Presence setting on the inner 3 rows. llmll!I To comply with ENl6005 set the presence timer to 30s or Timer 1 2 more 1 2 1 2 1 2 1 2 IR. *A×H When more than two sensors are installed in close proximity to each *A×H BwH c Dww other select different frequency settings for each sensor to prevent Frequency 3 4 cross intetference. 3 4 3 4 3 4 3 4 *Normal H Set to snow in instances where false door activations can result from *Normal H TI7f Snow  ffif Monitor blowing snow, leaves or rubbish in the door close area. Mode 5 5 . 5 Safety Refer to [ 11.Timing Chart of events] for full details on Safety Output *N.O.H Safety Output (Opto-Relay) Relay *N.O. N. C. w □ Output 6 6 A low reflected infrared signa! is indicated by a slow flashing Red/Green Travver Transvver* Reflection *Normal Ȩ LED. *Normal × To ignore ihis low reflection error state, set this dip switch to "Low Low Ref. Diagnostics Reflection"(ON). 7 7 IR Spot 7 IKSpot Yq}? llmll!I To comply with ENI6005 set to "Normal" Function Dip S witch® Description Possible Setting Options Direction When set to ON, pedestriaus moving away from the sensor will not be .  tä * ON detected. OFF *ON Detection RADAR 1 1 1 Refer to [1 !.Timing Chart of events] for full details on Activation Output *N.O.H Activation Output (Mechauical Relay) Activation [i] [jJ Relay *N.O. N.C.w OR Output 2 Activation Choose how relay output is configured. RADAR+ IR rows 2+ 3 RADAR Relay *OFF  *OFF Gil] ON  [jJ Output Configuration 3 3 3 Switch to OPEN to hold the door in the open position Door Hold *AutoH &AUTION *AutoH Open 4 4 4 Doorway Leam allows the 1" row of detection to be focused  inside tlie door close area without the detecting door movement.   ON[lJ Doorway *OFF *OFF Leam 4D When Doorway Learn is tumed ON, the sensitiviȩ level 5 of the inner row of detection is only at maximum w en the 5 outer rows of detection are activated Test Input When connected to a door controller without a TEST input, set to "OFF". *OFFH With TEST  When connected to a door controller with a TEST input, set to "ON" Without TEST •i• •i• Without TEST Setting *OFF Refer to [ 11.Timing Chart of events]. ®Dov ············-· ' ............... ' .. -······ from Door ON Controller 6 l!lill'iml Set to "ON" to comply with EN 16005 C®ov•··············· 1 .............. • ---·--- 6 8.DETECTION Detection Area Depth Adjustment: IR. (Inner 3 Rows) Detection Area Width Adjustment: IR. (Inner 3 Rows) QJJJ s::; DODO  l!lill'iml Verify that the detection area position conforms to EN16005 by using the Hotron Bearn Finder Detection Area Depth Adjustment: RADAR (Outer) * Detection area varies depending on walking speed * Adjustment possible in 3 ° steps as illustrated ' Near Radar sensor unit Installation height "2.2m" and Sensitivity set to "High" Installation height " 2.2m" and Sensitivity set to "Low" 2 o [ml 1 O l O 2 O 20 [ml 10 10 20 , .. v /. 1.0 (. ·. ... . .. ' 1\ ,-. -- ,.. - 2.0 r--... 3.0 '\ .. ·· v .,. r--.. 'ȱ \ [15 degree] setting y J l. [30 dcgree] setting J" .,, "r---... / 1 [45 degree} setting ) À-- - ..... - t-, , v '-- 1...1 1.0 1/ V 2.0 3.0 The above illustrated detection areas represent the actual position of the infrared and radar beams. The actual detection area observed will vary depending on the sensor installation environment, objects been detected and sensor settings. Please ensure that the detection area is set to conform to EN16005. SENSORPARTNERS.COM