HP Vectra VL6 6 Manuals

HP Vectra PCs HP Kayak PC Workstations DiagTools User’s Guide guard.bk : guard-fc.fb4 Page 1 Wednesday, June 30, 1999 3:06 PM Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. AMIDIAG is a trademark of American Megatrends Inc. Acrobat is a trademark of Adobe Systems Inc. Sound Blaster is a trademark of Creative Technology Ltd. in the United States and/or other countries. Microsoft, MS, MS-DOS, Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Hewlett-Packard France Commercial Computing Division 38053 Grenoble Cedex 9 France  1998 Hewlett-Packard Company Doc ver 2.1 06/99 for DiagTools ver 2.10 guard.bk : notice.fb4 Page ii Wednesday, June 30, 1999 3:06 PM User’s Guide guard.bk : title.fb4 Page iii Wednesday, June 30, 1999 3:06 PM

Etherlink IIIB ISA Network Interface Card (10BT) 3C509B-TP Installation Guide Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft Corporation. MMXTM is a trademark of Intel Corporation. Pentium® is a registered trademark of Intel Corporation. Hewlett-Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France 1 Connecting to a Netware 3.12 Server Windows for Workgroups 1 Connecting to a Netware 3.12 Server Windows for Workgroups Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96 • DOS and MS-Windows for Workgroups 3.11 media. • Novell Netware server 3.12 that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. • Netware client for DOS and MS-Windows. Device Configuration • I/O Base Address 300 • Interrupt Request Level 10 • Boot PROM Disabled • Transceiver Type Auto Select • Network Driver Optimization Windows or OS/2 Client • Maximum Modem Speed 9600 Baud • Plug and Play Compatibility Disabled • Full Duplex Disabled Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Power on the machine and allow it to boot to a DOS prompt. 3 Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s website) and execute 3C5X9CFG.EXE. 4 Select “CONFIGURE NIC,” and verify the resource settings listed above under the heading “Device Configuration.” 5 If changes are required, save those changes and exit. 1 Connecting to a Netware 3.12 Server Windows for Workgroups 6 Remove the 3com cards driver diskette and insert Netware client for DOS and MS-Windows disk 1. 7 Execute INSTALL.EXE and set lines 1-5 as listed below; 8 C:\NWCLIENT 9 YES 10 YES C:\WINDOWS 11 NO 12 3COM Etherlink III Parallel Tasking Family. 13 Highlight option 6 to continue with installation. 14 When prompted, insert the corresponding disks to complete file transfer and driver installation. 15 When the install utility is finished, press to restart the machine. 16 After windows loads, open the “NETWORK” folder, double-click the “NETWORK SETUP” icon. 17 Select “Networks”, and verify that “Novell Netware (Workstation Shell 4.0 and above)” is listed under “Install Windows support for the following network only:” and click on “OK.”