HP Workstation x4000 Manuals

Hewlett-Packard Company 3404 East Harmony Road Fort Collins, Colorado 80528 Read Before Installing 3DLabs Wildcat III 6110 Graphics Accelerator Card HP Product No. A8051A General HP Installation Instructions NOTE Before you install your graphics card, refer to the your workstation’s Technical Reference (www.hp.com/go/workstationsupport) for important system configuration information. CAUTION Graphic cards are susceptible to electrostatic shock. When handling your card always wear a properly grounded wrist strap and handle the card carefully. The latest workstation BIOS must be installed on your workstation before installing the new graphics card. The latest BIOS can be downloaded from http://www.hp.com/go/workstationsupport. If the latest BIOS is not installed, you may experience no video, PCI Option ROM errors and system stops during self- test (POST). In addition, if you have purchased and/or installed Windows® 2000, a chipset driver must be installed to enable AGP. If an AGP graphics card is not run in AGP mode, you may experience extremely slow graphics performance, system lockups and Windows® stop errors. The chipset driver can be downloaded from http://www.hp.com/go/workstationsupport. 1. Before opening your workstation to install the graphics card, disconnect all cables from the system. When refer- ring to your system model/type and for obtaining the proper driver version, please use the AxxxxX nomenclature found on the Serial Number plate on the back of the machine. 2. Following the procedures described in your workstation’s Technical Reference, install the graphics board into the AGP Pro slot (see the next diagram). Slide the board into the slot and ensure it is fully seated in the connector. 3. Attach your monitor cable to the primary port. If you have two monitors, attach the primary monitor to the pri- mary port and the second monitor to the secondary port. Use the included DVI-I dongle to attach an analog mon- itor to the either port.

VISUALIZE Workstations Interoperable Security for HP-UX and Windows NT Technical Workstations By Scott Key Solution Specialist

HP VISUALIZE fx2+, fx4+, fx6+ and Texture Module User’s Guide Printed in USA June 2000 Manufacturing Part Number: HP Part No. A5021-90001 Edition 0600 © Copyright 2000 Hewlett-Packard Company

* 18.1-inch LCD Color Monitor 18.1-inch Viewable Image User’s Guide HP D5065 Series L1800 ladoga.bk : ladgafc1.fb4 Page i Friday, January 15, 1999 3:17 PM

Fire GL2 User's Guide Information in this document is subject to change without notice. © 2000 Fire GL Graphics; All rights reserved.

HP Workstation x4000 Instructions for Re-Installing Processor(s) after replacing the system board, processor or processor turbocooler heatsink 1. If reusing the original processor and/or turbocooler heatsink, discard the old thermal interface material. You do not need to scrape off any thermal material that adheres to the processor or turbocooler heatsink. CAUTION Always add the fresh thermal interface material that is included in the support part kit for the processor, turbocooler heatsink, or system board. 2. Ensure that the ZIF socket lever on the system board is in the UP (open) position. 3. Orient the processor by matching the notches on the processor to the notches on the ZIF socket. 4. Carefully lower the new processor into place. When the processor is fully inserted, close the ZIF lever. CAUTION Be extremely careful inserting the processor. If you bend one of the pins, it will not go into the socket. 5. Center the fresh thermal interface material on the processor chip. 6. Place the turbocooler heatsink on the processor. Use the retaining clips to attach the turbocooler heatsink to the black plastic retainers on the system board. HP part # A6068-90015

HYDRAVISIONTM for Fire GL Installation and User's Guide
      © Copyright 2001, by ATI Technologies Inc. All rights reserved, including those to reproduce this guide or parts thereof, in any form without the express written permission of ATI Technologies Inc. Products may not be exactly as shown. Features, performance, and specifications may vary depending on operating environment and are subject to change without notice. Trademarks and/or registered trademarks are the properties of their respective owners. Adobe and Acrobat are trademarks of Adobe Systems Incorporated, which may be registered in certain jurisdictions. ATI is a registered trademark of ATI Technologies Inc. in Canada, the United States and/or other countries. Fire GL is a trademark of ATI Technologies Inc. in Canada, the United States, and/or other countries. MS-DOS, Windows, Windows NT, Windows 2000, Windows XP, DirectDraw and Direct3D are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. MACROVISION PRODUCT NOTICE A. Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098, and 4,907,093 licensed for limited viewing users only. B. In the printed collateral material that accompanies the Product, the following notice must be printed in an appropriate place in such materials: This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

ELSA Synergy II/GLoria II User’s Guide Printed in USA December 1999 Manufacturing Part Number: HP Part No. A1280-90026 Edition 1299 © Copyright 1999 Hewlett-Packard Company

VISUALIZE Workstations NT & HP-UX Functional Interoperability By Scott Key Solution Specialist

1 ELSA GLoria Synergy+ HP VISUALIZE Computers Printed in USA April 1999