Htek UC842 Manuals

1 Htek UC8xxSERIES SIP PHONE Auto Provision User Guide Nanjing Hanlong Technology Co., Ltd. 0086-25-84658050 www.htek.com [email protected]

Home PBXware SERVERware TELCOware SIPmon SIPProt Desktop & Mobile BRM UADs Appliances EOL From Bicom Systems Wiki Contents 1 Introduction - Htek Phones Configuration guide I 2 Installation I 2.1 Power Adapter I 2.2 Power over Ethernet (PoE) I 2.3 Factory Settings I 3 Registering Phone I 3.1 Manual Configuration I 3.2 Auto Provisioning I Introduction - Htek Phones Configuration guide This User Guide is written as general guide on how to set up the Htek phone models: UC804, UC806, UC840, UC842 and UC860. Installation This chapter describes how to install and connect the phone to the electrical power and data network, as well as how to apply factory settings. The following topics are covered: - Power adapter - Power over Ethernet (PoE) - Factory Settings

Hardware Overview LEDs 1. Power Indicator: Steady green when power on, blinking green when the call is ringing. 2. Line Keys Steady green: during the conversation, or plan to dial a call. Blinking red: the call is ringing. Off: idle interface Place a call Three ways to make a call: 1) Handset: Pick up the handset; enter the number, and then press the send soft key or press . 2) Speaker: Press or the line keys; enter the number, and then press the send soft key or press . 3) Headset: Press ; enter the number, and then press the send soft key or press . Note: You can also use Contacts or call log to dial the number you want, press place the call by the three ways mentioned. More, you can also alternate the mode during the call. End a call To end a call in three different modes: 1) Handset: hang up the handset or press the cancel soft key. 2) Speaker: press , or press the cancel soft key 3) Headset: press the cancel soft key. Answer a call 1) Handset: pick up the handset; 2) Speaker: press ; 3) Headset: press . Note: You can also reject the call by press the Reject soft key. Redial Press to redial the last call that dialed. Hold Press or press the hold soft key during a call to hold the call, Press or resume soft key to resume the call. Call Transfer Blind Transfer a. Press or transfer soft key during the conversation, the call is on hold now. b. Enter the number that transfers to. c. Press or the transfer soft key, and now the blind transfer completed. Attended Transfer (at least one line key set as Auto) a. Press or transfer soft key during the conversation, the call is on hold now. b. Enter the number that transfer to, and press the send soft key or . c. Start the second conversation, press or transfer soft key, then, transfer completed. Semi-Attended Transfer (at least one line key set as Auto) a. Press or transfer soft key during the conversation, the call is on hold now. b. Enter the number transfer to, and then press , then you can hear the ring tone. c. Press or the Tran soft key, and now the Semi-attended transfer completed. Call Conference Assuming that A and B are in conversation. A wants to bring C (or D & E) in a conference: 1) A press line 2, the call is placed on hold. 2) A enter the number of C and then press send soft key or . C answers the call. 3) A press or the conference soft key, then A, B and C are now in a conference. 4) If add D&E, press Line 3, the current conference is on hold, dial D and press , the four are in conference. Press line 4, and dial E, press , then A,B,C,D,E are in conference. Note: 1) If C does not answer the call, A can back to continue the conversation with B; 2) Once A hangs up the call, the conference is ended, while if B or C drops the call, A&C or A&B conversation continues. Call Mute Press to mute the microphone during the call Press again to un-mute the conversation.

Notices Information 1 Notices Information Copyright Copyright © 2005 - 2015 Nanjing Hanlong Technology CO., LTD. All rights reserved. Nanjing Hanlong Technology Co., LTD. owns all the right to revise and change this document at any time. And all the illustrations and instructions in this paper are subject to the copyright protection of legal law. No parts of this document may be used or reproduced, transmitted by the third parties for any purposes without the express written permission of Nanjing Hanlong Technology Co., LTD. When this document is made available on www.h-tek.com , hanlong Technology Co., LTD. gives its right to download and print copies of this content only for private use as a user manual. No parts shall have the right to alter, modify or use as commercial means without the express written permission of Nanjing Hanlong Technology Co., LTD. Safety cautions  To use the Phone follow the instructions in this manual.  To use the power adapter that delivered with the phone. Other power adapters may damage the phone.  The phone is only for indoor use. And also avoid in high humidity, water and some other liquids.  Do not use the phone during thunderstorms.  CE  FCC WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.