Humanscale M/Connect 2 Manuals

North America: +1 800 400 0625 Europe: +353 (0)1 858 0910 Asia Pacific: +852 2581 0570 EN FR ES IT DE NL 19 22 26 29 33 3 Assembly Instructions AR 36 3 M/Connect Hub M/Connect Dock USB-C Upstream Cable and USB-A Adapter Power Adapter ① ④ ② ③ Parts Included Installation Guidelines This product is intended to be used with Humanscale’s Monitor Arm product line and the following office desk styles placed on a non-skid surface: 1. Systems Furniture with panel hung surfaces 2. Systems Furniture with a floor mounted panel behind the desk 3. Systems Furniture with a desk mounted panel in the rear of the desk 4. Back-to-back desks sharing the same frame When mounting monitor arm and monitor(s) with this product on a freestanding desk/table: 1. The freestanding desk/table should have base that is no less than 30” deep and 66.5” wide 2. The freestanding desk/table should be a minimum of 200 lbs and placed on a non-skid surface. 3. The tabletop thickness should be no less than 1.2 inches and strong enough to support a minimum weight load of 165lb. CAUTION: DO NOT ROTATE MONITOR PAST REAR EDGE OF DESK. DOING SO CAN CREATE AN UNSTABLE SITUATION AND MAY CAUSE EQUIPMENT DAMAGE OR PERSONAL INJURY. 4 Front Panel Component Description USB A port Supports USB 3.1 Gen 1 USB A port Supports USB 3.1 Gen 1 3.5 mm TRRS jack To connect combined headphone and microphone headset Identifying Ports ① ① ② ②

Initial Disassembly Step 1 Remove Stem Screw Step 2 Remove Dock by pulling off from Hub Step 3 Remove Cable Retainer Screw to detach cable Tools Required Safety Glasses Flat Screwdriver Standard Hex Key Set Phillips Screwdriver Disassembly Instructions M/Connect 2 REV-00 Some components may not be recyclable in your area. 1 2 3 Steel Aluminum ABS >ABS< Hub and Clamp Disassembly Tools Required Safety Glasses Flat Screwdriver Standard Hex Key Set Phillips Screwdriver Step 1 Remove 4 Screws to detach from Slim Clamp and pull apart and set Hub aside Step 2 Remove L-Bracket Cover Step 3 Remove all screws, clips and washers to completely disassemble Disassembly Instructions M/Connect 2 REV-00 Some components may not be recyclable in your area. 1 2 3 ABS >ABS< Steel Steel Steel Steel Hub Disassembly Continued Remove all screws and covers to completely disassemble Note: Foam pad can be removed from bottom by scraping off. Tools Required Safety Glasses Flat Screwdriver Standard Hex Key Set Phillips Screwdriver Disassembly Instructions M/Connect 2 REV-00 Some components may not be recyclable in your area. Aluminum FR4 ABS >ABS< ABS >ABS< Steel Steel Dock Disassembly Tools Required Safety Glasses Flat Screwdriver Standard Hex Key Set Phillips Screwdriver Disassembly Instructions M/Connect 2 REV-00 Some components may not be recyclable in your area. Step 1 Remove Sheetmetal Bracket Security Screw and slide out dock Step 2 Remove all screws to disassemble unit Step 3 Step 4 Remove PCBA K-Lock Plate is head staked to bottom cover 1 2 3 4 ABS >ABS< Steel FR4

USER GUIDE Table of Contents 3 4 6 9 14 3 PARTS REQUIRED M/Connect 2 Parts A (1) M/Connect 2 Hub and Dock B (1) Power Adaptor C (1) Power Cable (Localized) D (1) USB-C Upstream Cable with USB-A Adapter E (1) Upstream Cable Retainer A B C D E 4 Front Panel Component Description USB A port Supports USB 3.1 Gen 1 USB A port Supports USB 3.1 Gen 1 3.5 mm TRRS jack To connect combined headphone and microphone headset 1 2 1 2 IDENTIFYING COMPONENTS

M/Power M/Connect 2 Assembly Instructions North America: +1 800 400 0625 Europe: +353 (0)1 858 0910 Asia Pacific: +852 2581 0570 EN 1-8 FR 9-16 2 3 mm Hex Key 4 mm Hex Key 5 mm Hex Key Cable Routing Hook INSTALLATION HARDWARE 4 Standard VESA Bracket Screws With Each VESA Plate: 4 Plastic Spacers 4 Extended VESA Bracket Screws VESA Plate and Cover 3 STEP 1: ATTACH MOUNT TO WORK SURFACE Before you install your new M/Flex and monitor arms you will need to set up your M/Connect 2 or M/Power base. Before proceeding, please refer to the installation manual that came with your M/Connect 2 or M/Power for instructions on mounting the base to your work surface. STEP 2: BRACKET ASSEMBLY AND CABLE CLIP SINGLE AND DUAL MONITOR APPLICATIONS 1. With the Lever (A) open, position the Dual Bracket (B) at the desired height on the Post (C). 2. Close the Lever entirely. 3. If you are using a second monitor, lift and remove the Cover (D). D A B C TRIPLE MONITOR APPLICATIONS 1. Remove the two set screws (E) that retain the Bracket Cap (F). Lift the Bracket Cap (F) upwards to remove it. 2. Install the Extension Bracket (G) on top of the Dual Bracket. Insert the Tabs (H) into the Pockets (J). Replace the Set Screws. Tighten screws until the Extension Bracket is secure and the screws are flush with the surface. 3. Insert the Bracket Cap into the top of the Extension Bracket. Push down until it clicks into place. F H G J E F