Hunter 21101 Manuals

Hunter Fan Company 41681-01 • 02/20/04 Step 1 Choose the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety, reliable operation, maximum effi ciency, and energy savings. Choose a fan site where: • No object can come in contact with the rotating fan blades during normal operation. •  e fan blades are at least 7 feet above the fl oor and the ceiling is at least 8 feet high. •  e fan blades have no obstructions to air fl ow, such as walls or posts, within 30 inches of the fan blade tips. •  e fan is directly below a joist or support brace that will hold the outlet box and the full weight of the fan. Tools and Supplies You May Need Checklist for Existing Fan Site If you want to use an existing fan site, complete the following checklist to determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page. Fan Support System o Fan attaches directly to building structure. o Fan support system will hold full weight of the fan and light kit. Ceiling Hole o  e outlet box clearance hole is directly below the joist or support brace. Outlet Box o  e outlet box is an UL-approved octagonal 4” x 1-1/2” outlet box (or as specifi ed by the support brace manufacturer). o  e outlet box is secured to the joist or support brace by wood screws and washers through the inner holes of outlet box. o  e outer holes of the outlet box are aligned with joist or support brace. o  e bottom of the outlet box is recessed a minimum of 1/16” into ceiling. Wiring o  e electrical cable is secured to outlet box by an approved connector. o Six inches of lead wires extend from outlet box. If your existing fan site is suitable, go to your fan manual and begin with 2 • Installing the Ceiling Plate. Step 2 Cut the Ceiling Hole 2-1. Locate the site for the ceiling hole directly below the joist or support brace that will hold the outlet box and fan. 2-2. Cut a 4” diameter hole through the drywall or plaster of the ceiling. You will use the hole to install the support brace and outlet box. Step 3 Install a Support Brace, If Necessary Determine if there is a ceiling joist directly above the ceiling hole. If the joist is there, determine if it is positioned to allow you to recess the outlet box a minimum of 1/16” into the ceiling. If NOT, install a support brace as follows: 3-1. Attach a 2” x 4” support brace between two joists. Position it to allow you to recess the bottom of the outlet box a minimum of 1/16” into the ceiling. 3-2. Check the support brace to ensure it will support the full weight of the fan and light kit. Step 4 Install the Outlet Box 4-1. Obtain a UL-approved octagonal 4” x 1-1/2” outlet box, plus two #8 x 1-1/2” wood screws and washers, available from any hardware store or electrical supply house. 4-2. Orient the outlet box so that both the inner and outer holes in the box align with the joist or support brace. 4-3. Drill pilot holes no larger than the minor diameter of the wood screws (5/64”) through the inner holes of the outlet box. 4-4. Attach the outlet box directly to the support brace or joist with two #8 x 1-1/2” wood screws and washers.  e bottom of the outlet box must be recessed a minimum of 1/16” into the ceiling. Step 5 Prepare the Wiring 5-1. Make sure the circuit breakers to the fan supply line leads and associated wall switch location are turned off . If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. 5-2.  read the fan supply line through the outlet box so that the fan supply line extends at least 6” beyond the box. 5-3. Attach the fan supply line to the outlet box with an approved connector, available at any hardware store or electrical supply house. 5-4. Make certain the wiring meets all national and local standards and ANSI/ NFPA 70. You have now successfully prepared your ceiling fan site. For instructions to install your ceiling fan, go to your fan manual and continue with 2 • Installing the Ceiling Plate. CAUTION: All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualifi ed electrician. Fan Support System Outlet Box Fan Support System Wiring Suitable Existing Fan Site • Drill • Keyhole saw • 2’ x 4’ support brace • UL-approved octagonal 4” x 1-1/2” outlet box • Two #8 x 1-1/2” wood screws and washers • Approved connector for electrical wire Preparing the Fan Site 8’ Minimum Ceiling Height 7’ Minimum to Floor 30” From Wall or Nearest Obstruction Step 5 Step 4 Steps 2 – 3

Modelos TIPO 2 Modelos TIPO 2 Modelos TIPO 2 Formulario# 42678-02 20100309 ©2010 Hunter Fan Co. Para sus registros y en caso que requiera hacer efectiva su garantía Para referencia, también adjunte su recibo o una copia de su recibo al manual. __________________________________________ Nombre de modelo __________________________________________ Modelo Nº __________________________________________ Fecha de compra __________________________________________ Lugar de compra English Español Manual de Installatión y Operatión

PARTS GUIDE PARTS GUIDE Hunter Fan Company • 7130 Goodlett Farms Pkwy. #400 • Memphis, TN 38016 • www.hunterfan.com • 98000-01-995 06-01-2010 • ©201 Using this Parts Guide, make sure all parts are included in the box. If parts are missing, DO NOT RETURN THIS ITEM TO THE STORE, call 888-830-1326 for assistance. THIS PARTS GUIDE IS FOR REFERENCE ONLY. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. Using this Parts Guide, make sure all parts are included in the box. If parts are missing, DO NOT RETURN THIS ITEM TO THE STORE, call 888-830-1326 for assistance. THIS PARTS GUIDE IS FOR REFERENCE ONLY. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. Parts List Model # 21101 Asm. Dwg. # 99468-01 Finish Brittany Bronze Item # Item Name Qnty Part # 1 * Hanging System Kit 1 96760-66 2 Ceiling Plate 3 Canopy 4 Canopy Trim Ring 8 Setscrew 27 Low Profile Washer 62 Canopy Screw 64 Wood Screw 65 Wood Screw 68 Flat Washer 71 Mounting Isolator 100 * Screw, Low Profile 7 Hanger Ball / Downrod Assembly 1 74229-02 44 Blade Iron Set 1 96004-05 46 Blade Set 1 G0253-93 47 Screw, Blade Iron Armature 11 65457-05 60 Hardware Kit 1 99468-00-860 66 Blade Grommet 67 Blade Assembly Screw 69 Screw, Machine, 6-32 70 Wire Connector 131 Screw, Switch Housing Assembly 75 Balancing Kit 1 07570-01 49 Light Kit Assembly 1 99469-01 134 Decorative Sleeve 3 89210-01 78 Pull Chain 2 63756-54 76 Pull Chain Pendant 1 77800-02 76 Pull Chain Pendant 1 77801-02 202 Light bulb / Bulb 3 77646-04 150 Globe/Shade 3 89230-01 Hardware (Drawn to Scale) Fan Parts (Not Drawn to Scale) Hanger Bracket Assembly Blade Assembly Switch Housing Assembly 2 7 3 4 12 46 49 202 134 78 76 44 Screw, Switch Housing Assembly Screw, Machine, 6-32 Screw, Low Profile Setscrew Mounting Isolator Screw, Blade Iron Armature Canopy Screw Flat Washer Blade Assembly Screw 3” Wood Screw Low Profile Washer Balancing Kit Wire Connector 1.5” Wood Screw Blade Grommet 27 65 68 64 100 62 8 71 47 67 66 131 69 75 70 x 1 x 2 x 4 x 2 x 3 x 4 x 1 x 11 x 4 x 16 x 3 x 3 x 1 x 4 x 16

Type 2 Models Type 2 Models Type 2 Models Form# 42678-01 20090608 ©2009 Hunter Fan Co. For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. __________________________________________ Model Name __________________________________________ Model No. __________________________________________ Date Purchased __________________________________________ Where Purchased Owner’s Guide and Installation Manual