I-Tech DA011 Manuals

LCD monitor DA011OSD operation Hi i^i® lig:::iii -fa l-TECH COMPANY i-Tech Company LLC TOLL FREE: (888) 483-24 8 • EMAIL: [email protected] • WEB: www.iTechLCD.com Safety Instruction Read and follow these instructions when connecting and using your LCD monitor: Operation: 1. Keep the monitor out of direct sunlight and away from stoves or any other heat source. 2. Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics. 3. Do not block the ventilation holes on the cabinet. 4. When positioning the monitor, make sure the power plug and outlet are easily accessible. 5. If turning off the monitor by detaching the power cable or DC power cord, wait for seconds before attaching the power cable or DC power cord for normal operation. 6. Do not subject the LCD monitor to severe vibration or high impact conditions during operation. 7. Do not knock or drop the monitor during operation or transportation. Maintenance: 8. To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by placing your hand or fingers on the LCD panel. 9. Unplug the monitor if you are not going to use it for an extensive period of time. 10. Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your monitor. 11. To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment. 12. If your monitor gets wet, wipe it with dry cloth as soon as possible. 13. If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord. Then, remove the foreign substance or water, and send it to the maintenance center. 14. Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or extreme cold. 15. In order to maintain the best performance of your monitor and use it for a longer lifetime, please use the monitor in a location that falls within the following temperature and humidity ranges. Temperature: 5-35°C 41-95°F Product Installation 1. Switch off the power on both your monitor and your computer. The Power Switch is located in the right of the monitor. 2. Connect the power cord to the AC outlet, and connect the power to the monitor through the AC/DC adapter. 3. VGA Signal-Plug one end of the 15-pin signal cable to the video signal connector at the rear of the PC system and the other end to the monitor. Secure the connectors with the screws on the cable connector at both ends. 4. (Optional) DVI Signal-Plug one end of the DVI signal cable to the video signal connector at the rear of the PC system and the other end to the monitor. Secure the connectors with the screws on the cable connector at both ends. 5. (Optional) HDMI Signal-Plug one end of the HDMI signal cable to the video signal connector at the rear of the PC system and the other end to the monitor. Secure the connectors with the screws on the cable connector at both ends. 6. (Optional) RS232 Connection- Plug one end of RS232 cable to com-port connector on your PC system and the other end to the monitor. Secure the connectors with the screws on the cable connector at both ends. 1. Main Menu : If push the " MENU" key the screen will appear this main menu page, you can use the "UP" or"ADJ. +" AND "Down" or "ADJ. -" key ( Shown in Pid ) to select the function you need. Main Menu 1 ! 1 • ! M *+ | M Ml [ M M \ DPI 1 ! 1 • ! M *+ | M Ml [ M M \ DPI Br i g h t n e s s Scr een Se 11 i ngs C o l o r Temp Language OSD Menu VGA-DV1 1 ! 1 • ! M *+ | M Ml [ M M \ DPI I ■ "i ■ is ± is ■ ■ > f t \ ^ | B 1 ! 1 • ! M *+ | M Ml [ M M \ DPI RecaJ 1 i a | 0 g -19 2 0X1030 1 ! 1 • ! M *+ | M Ml [ M M \ DPI ^ ^ ^ ^ ^ ^ ^ ^ The end of this page will be shown the working resolution and frequency. a. Auto Adjust If select this function on OSD MAIN MENU and push the MENU key. In this function, that will be activated the auto adjusting for the picture. Auto Adjust