Icom IC-2720H Manuals

Icom IC–2720H Mini–Operating Guide by W5JCK, September 2007 Page 1 of 6 Icom IC-2720H VHF/UHF Radio Mini–Operating Guide by W5JCK 1 [PWR] Power Switch Press and hold 1 sec. to turn power On/Off. 2 [SET●LOCK] Set, Lock Switch ● Press to enter Set mode. ● Press and hold for 1 sec. to switch the Lock function On or Off. 3 [LOW●PRIO] Output Power, Priority Switch ● Press to change the power output level. ● Press and hold for 1 sec. to start the Priority Watch operation. 4 [TONE●DTMF] Tone, DTMF Switch ● Press to select a Tone function. ● Press and hold for 1 sec. to turn DTMF memory encoder On or Off. 5 [DUP●MONI] Duplex, Monitor Switch ● Press to select between DUP-, DUP+, and Simplex operation. ● Press and hold for 1 sec. to switch the Monitor function On or Off. 6 [MAIN●BAND] L/R Band Switches ● Press to select the main band for L/R side. ● Press and hold for 1 sec. to select operating frequency band for L/R side. 7 [V/MHz●SCAN] L/R VFO/MHz Tuning, Scan Switches ● Press to select between VFO mode and 1 MHz Tuning mode for L/R side. ● Press and hold for 1 sec. to start scan for L/R side. ● Press to stop a scan for L/R side. 8 [M/CALL●MW] L/R Memory/Call, Memory Write Switches ● Press to select between Memory, Call, and Weather Channel modes for L/R side. ● Press and hold for 1 sec. to select a memory channel for L/R side for programming. 9 [VOL] L/R Volume Control Switches Turn to adjust audio for L/R side. 10 [DIAL] L/R Tuning Dials Turn to select operating frequency, memory channel, setting for Set mode item, or scanning direction for L/R side. 11 [SQL] L/R Squelch Control Switches Turn to adjust squelch level for L/R side.

DUAL BAND FM TRANSCEIVER i2720H SERVICE MANUAL

Icom IC-2720H Step-by-Step Programming Guide Also applies to IC-2710H (except that the M/CALL button on the IC-2710H is called S.MW) Noji Ratzlaff Set the radio to communicate with a repeater at 146.780– MHz, 100.0 Hz tone 0. Turn on the radio and make sure it’s unlocked (press and hold SET to unlock) 1. Press the right MAIN to select the right transceiver 2. If the right display is in Memory mode, press the right V/MHz to enter VFO mode 3. Press the right V/MHz to select tens of MHz, then turn the right big knob so that the right display reads 14 4. Press the right V/MHz to select MHz, then turn the right big knob so that the right display reads 146 5. Press the right V/MHz to select kHz, then turn the right big knob so that the right display reads 146.780 6. Press SET repeatedly until the lower right shows rt (repeater tone) 7. Turn the right big knob until the right display reads 100.0 8. Press TONE to exit SET mode, then press TONE again to set the tone for this repeater 9. Select the desired power level by pressing LOW repeatedly Your radio is now set to transmit as specified Store and name the current repeater and tone settings in a memory channel 0. Follow the procedure above to set your radio for the frequency of your choice 1. If the right display is in Memory mode, press the right V/MHz to enter VFO mode 2. Press and hold the right M/CALL until you hear a single beep 3. Turn the right big knob until the right display reads 37 4. Press and hold the right M/CALL to save the frequency and settings Now stored in memory channel 37 Recall a stored memory setting 0. Turn on the radio and make sure it’s unlocked (press and hold SET to unlock) 1. If the right display is not in Memory mode, press the right M/CALL to change to Memory mode 2. Turn the right big knob until the right display reads your desired channel number The stored channel is now ready for use