Instrumentation Industries RTC 15-D Manuals

Product Specifi cations Sterilization / Disinfection Always carefully examine the physical integrity of this product after processing. Do not use if cracking or crazing is seen, or if parts fi t together improperly after processing. RTC 22-A — RTC 23-A These products are designed to be Reusable. (May be processed up to 30 times at the parameters provided below.) They are packaged as non-sterile; Instrumentation Industries, Inc. recommends processing before initial use. Reprocess when replacing the circuit at the parameters provided below. Recommendations for RTC 22-A and RTC 23-A: Carefully follow facility guidelines for preparing products and solutions for the sterilizing and disinfecting methods and equipment being used. Sterilization and High Level Disinfection Procedures have been validated for the following equipment and methods: Sterilization Steam Autoclave Do not exceed 135°C/275°F. High Level Disinfection Pasteurization Pasteurize at 70°C +/- 3°C (153° - 163°F) for a minimum of 30 minutes. Cold Chemicals Recommended Chemical: 2-4% Activated Glutaraldehyde Disinfect according to validated parameters. Follow the chemical manufacturer’s recommendation for temperature and soak time. Chemical disinfection should be followed by sterile water rinse. Exposure time should be based on the manufacturer’s indication for use as a high-level disinfectant or sterilant. Do not use alcohol or chemicals containing dimethyl ammonium chloride. Use: Reusable Inlet: 22mm I.D. Outlet: 15mm I.D./22mm O.D. Length: 2” Materials Body: Polyetherimide Cap: Silicone Rubber Color Body: Amber Cap: Clear Use: Single Patient Reuse (see Panel A for info) Inlet: 22mm I.D. Outlet: 15mm I.D./22mm O.D. Length: 2” Materials Body: Polystyrene Butadiene Cap: Thermoplastic Rubber Color Body: Clear Cap: Clear Use: Reusable Inlet: 15mm I.D./22mm O.D. Outlet: 15mm I.D./22mm O.D. Length: 2” Materials Body: Polyetherimide Cap: Silicone Rubber Color Body: Amber Cap: Clear Use: Single Patient Reuse (see Panel A for info) Inlet: 15mm I.D./22mm O.D. Outlet: 15mm I.D./22mm O.D. Length: 2” Materials Body: Polystyrene Butadiene Cap: Thermoplastic Rubber Color Body: Clear Cap: Clear RTC 15-D Metered Dose Inhaler (MDI) Adapter RTC 15-P Metered Dose Inhaler (MDI) Adapter Use: Single Patient Reuse (see Panel A for info) Inlet: 15mm I.D. Outlet: 15mm I.D. Length: 2” Materials Body: Polystyrene Butadiene Cap: Thermoplastic Rubber Color Body: Clear Cap: Clear RTC 22-A Metered Dose Inhaler (MDI) Adapter RTC 22-D Metered Dose Inhaler (MDI) Adapter RTC 23-A Metered Dose Inhaler (MDI) Adapter RTC 23-D Metered Dose Inhaler (MDI) Adapter MDI Adapter Installation & Usage Directions RTC 15-D RTC 15-P RTC 22-A RTC 22-D RTC 23-A RTC 23-D For use with metered dose inhaler canisters, with standard size metal (.109 inch diameter) or plastic (.124 inch diameter) stems. Instrumentation Industries, Inc. Instrumentation Industries, Inc. 2990 Industrial Blvd. Bethel Park, PA 15102 US Toll Free: 1-800-633-8577 Business: 1-412-854-1133 US Toll Free Fax: 1-877-633-8661 Fax: 1-412-854-5668 E-mail: [email protected] www.iiimedical.com ECO 2526 Rev. J 2-18 — Not made with Natural Rubber Latex — Not made with Di(2-ethylhexyl) phthalate (DEHP) Use: Single Patient Reuse (see Panel A for info) Inlet: 15mm O.D. Outlet: 15mm I.D. Length: 2" Materials Body: Polystyrene Butadiene Cap: Thermoplastic Rubber Color Body: Clear Cap: Clear G H RTC 15-D — RTC 15-P — RTC 22-D — RTC 23-D These products are designed for Single Patient Reuse. (Can be used to repeatedly administer medications to one single patient while installed in a breathing circuit.) They are packaged as non-sterile; Instrumentation Industries, Inc. recommends processing before initial use. Discard when replacing the circuit according to facility guidelines. Recommendations for RTC 15-D, RTC 15-P, RTC 22-D, and RTC 23-D: Carefully follow facility guidelines for preparing products and solutions for the sterilizing and disinfecting methods and equipment being used. Sterilization and High Level Disinfection Procedures have been validated for the following equipment and methods: Sterilization STERRAD 100S Full short sterilization cycle (Hydrogen peroxide gas plasma, 55 minutes, 45°C - 55°C (113°F - 131°F)). High Level Disinfection Pasteurization Pasteurize at 70°C +/- 3°C (153° - 163°F) for a minimum of 30 minutes. CIDEX® OPA Prepare CIDEX® OPA solution. Totally submerge adapter in the disinfectant. Immerse device completely, eliminating air pockets, in CIDEX® OPA solution for a minimum of 12 minutes at 20°C (68°F) to destroy all pathogenic microorganisms. Remove device from the solution and rinse thoroughly as per these rinsing instructions: • Following removal from CIDEX® OPA solution, thoroughly rinse the adapter by immersing it completely in a large volume (e.g. 2 gallons) of water. Sterile water rinse is recommended unless potable water is acceptable. • Keep the device totally immersed for a minimum of 1 minute in duration. • Manually fl ush all devices with large volumes (not less than 100 mL) of rinse water. • Remove the device and discard the rinse water. Always use fresh volumes of water for each rinse. Do not reuse the water for rinsing or any other purpose. • Repeat the procedure two (2) additional times, for a total of three (3) rinses, with large volumes of fresh water to remove CIDEX® OPA solution residues. Residues may cause serious side effects. • Dry using sterile, lint-free cloths. DO NOT STEAM AUTOCLAVE RTC 15-D — RTC 15-P — RTC 22-D — RTC 23-D! Visit iiimedical.com/symbols.pdf for the Glossary of Symbols used in Instrumentation Industries, Inc. labeling. Made in USA These user instructions are available in Canadian French at iiimedical.com Ces instructions d’utilisation sont disponibles en français canadien à iiimedical.com