Intel S3000PT Manuals

INTEL© Intel® Server Board S3000PT Spares/Parts List and Configuration Guide – for Production Products A reference guide to assist customers in ordering the Intel® Server Board S3000PT ~Subject to Change without Notice~ Rev 1.1 – Production Version December, 2006

Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright © 2006, Intel Corporation. All rights reserved. Thank you for buying an Intel® Server Board S3000PT. The following information will help you integrate your new server board into a third-party chassis. For details on selecting a third-party chassis, please see http://www.intel.com/go/serverbuilder and http://support.intel.com/support/motherboards/server. When installing the server board into a third-party chassis, refer to the instructions that came with the chassis. If you are not familiar with ESD (Electrostatic Discharge) procedures used during system integration, please see the Intel® Server Board and Server Chassis Safety Information document at http://support.intel.com/support/motherboards/server/sb/cs-010770.htm. Intel® Server Board S3000PT Quick Start User's Guide Warning Safety information: Read all the safety and caution statements in this document before performing any of the instructions. Also, see the Intel® Server Board and Server Chassis Safety Information document at: http://support.intel.com/support/motherboards/ server/sb/cs-010770.htm for complete safety information. Caution Electrostatic discharge: Observe normal Electrostatic Discharge (ESD) procedures during system integration to avoid possible damage to the server board and/or other components of the system. D69382-001 *D69382-001* 5 Install DIMM Memory Go to Side 2. DDR2 DDR DDR2 DIMM Memory Identification DIMM notch and socket bump must align as shown. DIMM Sockets 2 4 3 1 DIMM 2B Socket DIMM 1A Socket DIMM 2A Socket DIMM 1B Socket Bank 2 Bank 1 Memory Type: Minimum of one 256-MB, DDR2 533/667 MHz compliant unbuffered, ECC or non- ECC, SPD SDRAM 240-pin gold DIMM. Notes and Cautions: Populate DIMMs in the order of: 1A, 1B, 2A, 2B. The DIMM size, speed, and vendor must be the same within a bank. However, the DIMM size can vary be- tween banks. For example, Bank 1 can use two 256-MB DIMMs and Bank 2 can use two 512-MB DIMMs. For additional memory configurations, go to: http://support.intel.com/support/motherboards/server Memory sizing and configuration are guaranteed only for qualified DIMMs approved by Intel. 1 2 3 To Install DIMMs: Open both DIMM socket levers. Note location of alignment notch. Insert DIMM, making sure the connector edge of the DIMM aligns correctly with the slot. Push down firmly on the DIMM until it snaps into place and both levers close. 4 This server board does not support DDR memory. You must use DDR2 DIMMs to avoid possible damage to server board DIMM sockets. Avoid touching gold contacts when handling or installing DIMMs. 4 Install Passive Heatsink 2 3 1 4 CAUTION: Do not over-tighten fasteners. TIM Note: Heatsink styles may differ. Processor Socket Chassis Front AIRFLOW The heatsink may have thermal interface material (TIM) on the underside of it. Use caution so that you do not damage the TIM. Use gloves to avoid sharp edges. If present, remove the protective film on the TIM. If no TIM is present, evenly coat the heatsink with a thermal compound. Align heatsink fins to the front and back of the chassis for correct airflow. Each heatsink has four captive fasteners and should be tightened using the following procedure: Lightly tighten each fastener diagonally, according to the numbers shown. Securely re-tighten each fastener again in the same order. 4 3 2 1 3 Install Processor 2 1 2 1 2 3 1 2 1 1 1 2 1 2 A. Open the Socket Lever Push the lever handle down and away from the socket to release it. Pull the lever and open all the way. B. Open the Load Plate Push the rear tab with your finger tip to bring the front end of the load plate up slightly. Open the load plate as shown. 1 2 C. Remove the Processor Protective Cover Take the processor out of the box and remove the protective shipping cover. 1 D. Install the Processor Orient the processor with the socket so that the processor cutout matches the socket notch. Install the processor as shown. 2 1 E. Remove Socket Protective Cover Grasp the socket protective cover tab and pull away from the load plate as shown. Remove the socket protective cover and store for future use. 2 1 F. Close Load Plate and Socket Lever Close the load plate all the way as shown. 2 3 1 With your finger, push down on the load plate as shown. Close the socket lever and ensure that the load plate tab engages under the socket level when fully closed. Notes and Cautions 1. When unpackaging a processor, hold it by the edges to avoid touching the pins. 2. This server board has a "zero-insertion force" socket. If processor does not drop easily into socket, make sure lever is in the fully open position. 2 Install Server Board Place the board(s) into the chassis, making sure that back panel I/O ports and chassis or I/O shield openings align correctly. Verify that server board mounting holes align correctly with the chassis standoffs. Place the server board into the chassis as shown below. Use the fasteners that came with your chassis to secure the server board to the chassis. 1 Prepare Chassis Refer to the instructions that came with your chassis for preparatory steps. Tools Required Phillips* screwdriver Anti-static wrist wrap Minimum Hardware Requirements To avoid integration difficulties and possible board damage, your system must meet the following minimum requirements: • Processor: Intel® Celeron® D processor, minimum 2.4 GHz with chassis compatible fan / heatsink • Memory Type: Minimum of one 256-MB, DDR2 533/667 MHz compliant unbuffered, ECC or non-ECC, SPD SDRAM 240-pin gold DIMM • Power: Per board, minimum of 200 W with 2 A of standby current, which meets the SSI EPS 12-V specification

Intel® Server Board S3000PT Technical Product Specification D69383-004 Revision 1.3 February 2007 Enterprise Platforms and Services Division