Intelbras REP 8000 Manuals

User guide REP 8000 RF Range amplifier Congratulations, you have just purchased a product with Intelbras quality and security. The 8000 System RF Range Amplifier was developed to amplify the coverage signal of the system as a whole, where up to 4 amplifiers can be added to each alarm center, thus extending the range and communication of the other devices with the alarm center. 1. Care and security » Follow all instructions in the manual/guide for product installation and handling. » Perform the installation in environments not susceptible to factors such as rain, fog and splashes of water. » Wireless communication technology, when exposed to environments with high power radia- tion, may suffer interference and have its performance impaired. Example: locations near TV towers, AM/FM radio stations, amateur radio stations, etc. » Do not install the amplifier for air conditioning equipment or heaters. » Clean only the external part of the device, using only a damp cloth (do not use chemical solvents). » Do not subject the device to excessive pressure or knocks/falls. » Do not cover the device with adhesives, paper or inks. » Do not expose directly to sunlight. » Confirm that the installation site is stable and appropriate. » Only perform configurations and installations by qualified personnel. » Perform periodic tests on it to validate weather conditions, battery level and other factors so that the site supervised by the system is always able to operate properly. 2. Especificações técnicas Frequency of operation RF signal from 915 to 928 MHz Modulation DSSS BPSK 40 kbps Maximum trans. power 18 dBm Transmission range¹ 600 m with direct line of sight open field² DC power supply 1 rechargeable battery of 3.7 Vdc/3,000 mAh (included with amplifier) AC power supply (included with amplifier) Input: 100/240 Vac ~ 50-60 Hz Output: 7 Vdc – 500 mA Operating temperature -10 to 50 °C @ 90% of humidity Compatibility 8000 Wireless Security System Anatel Homologation Yes Protection against violation Tamper key Anti-jamming Against invasive signals Color White Dimensions ( W × H × D) 122 × 122 × 47 mm Weight 256 grams (with source) 1 Intelbras wireless systems are tested to the highest standards and bring high reliability, but due to their use/installation in various scenarios, some considerations must be taken into account: » Transmitters/receivers may be disturbed by radio signals, natural interference, location of operation of the devices, climatic issues and other adversities affecting the transmission of data regardless of the frequency or technology used, since the means of transmission is adverse and different from place to place. » The receivers/transmitters of the devices have an internal processing time, and only receive the data necessary for communication between them after this particular time for the system. » Wireless devices must be tested regularly to determine if sources of interference exist and to protect against possible failures. 2 Maximum range distance between the AMT 8000 alarm center and the REP 8000 RF range ampli- fier, and the range between the amplifier can extend up to 600 m more according to the environ- ment and operating conditions. 3. Features » AMT 8000 system coverage area amplifier. » Protection against malicious signals. » Encryption in data transmission between devices. » Ease of installation and handling. » Extension of the RF signal up to 600 meters beyond the maximum limit for communication with the center unit, so with the use of the amplifier a device can communicate at a dis- tance of up to 1.2 kilometers with the alarm center in the case of direct line of sight and without barriers. » Rechargeable battery. » 7 Vdc/500 mA source included. Important: each AMT 8000 alarm center can have up to 4 amplifiers operating simulta- neously, but all in separate operation from each other, so there is no possibility of an amplifier being used to extend the signal to another REP 8000, only in direct use between devices and alarm center. 4. Registration at the center unit To register the amplifier with the alarm center, press the synchro¬nization key on the center unit and then press the key on the amplifier located on its back, as shown in the following image, removing the product from the fixing bracket. Check if the LED on the front part of the amplifier will flash green, indicating the success of the registration. If the LED flashes orange, the signal is intermittent or weak and if the LED flashes red, there was some fault and the process must be repeated. The amplifier will be addressed with the center unit according to the sequence performed, respecting the maximum limit of 4 devices of this type. Synchronization key of the amplifier To check if the amplifier installation location is within the RF signal range, press the synchro- nization key, and if the LED flashes green the communication is correct, in orange the com- munication is intermittent/weak and in red there is no commu¬nication with the center unit. If there is no signal or weak signal, it must be relocated/changed if necessary. After pressing the synchronization key, the LED indication will flash for 15 minutes, thus giving time to find an ideal position where it is flashing only in green color. If there is no time to find an optimal position, simply press the synchronization key again. To register other amplifiers/accessories through keyboard commands and further information/ configurations, please refer to the complete manual of the AMT 8000 center. Note: when registering the REP 8000 amplifier to the alarm center using the synchronization key, perform the practice safely, because the alarm center is energized, so as not to bring risks to the installer and the equipment. 5. Installation The REP 8000 amplifier has a specific base to be fixed on various surfaces, such as walls, among others. To remove the amplifier from the base when it is fixed on some surface, slide it up and to put it back on the standalone base if it is fixed or in manual use, follow the base’s indicative marking. Fasten the base with screws1 or double-sided tapes1 on the desired surface and then attach it to the base. Make sure the base is correctly fixed to the surface and the amplifier is fixed to the base, so that they do not come Off. Bracket for fixing to surfaces 1 Screws, double-sided tape and other accessories are not included with the amplifier and must be pur- chased separately. 6. Registration of devices For a device to pass through the RF REP 8000 signal amplifier’s range extension, it is necessary that it does not have direct communication with the AMT 8000 alarm center or the commu- nication is poor with indication ranging from orange to red, otherwise it will communicate directly with the center without passing through the amplifier. To check the signal strength of the 8000 line devices, press the synchronization key on them, where the indicator LED will show their status, and if the LED flashes green, the signal is ex- cellent, in orange the signal is intermittent or weak and in red there is no communication (only for the XAT 8000 keyboard the status will be shown through a message on its own display). After validating the need to pass the communication through the amplifier, remove the power from the device to have its communication pass through the amplifier and after 3 seconds replace again. After the device initialization time (varies from 0 to 60 seconds depending on the type) press its synchronization key again and through the indicator LED or on the display in case the XAT 8000 is the new communication status that follows the same results above (to check if the device is passing through the repeater, on the XAT 8000 keyboard press the Menu key and then navigate to the Wireless Signal option by the Arrow down key and press Enter, select the desired device and confirm with Enter. The device level will be shown on the display where it will vary from 1 to 10 and the device’s route will be shown. If the device is in direct communication with the center unit, the position of the device plus the letter C will be shown, if the device is passing through the repeater, the position of the device plus the letter R will be shown accompanied by the position of the repeater. Ex.: R1 repeater 01, R2 repeater 02, R3 repeater 03 and R4 for repeater 04. 7. Operation The RF range amplifier when registered in the alarm center will extend the signal range of the RF signal, and the amplifier needs to be installed in a place where it recei-ves a good signal from the control panel and also be in the area covered by the other devices where the signal will be extended. Avoid an excessive number of physical barriers between 8000 line devices and RF network amplifiers. Signal range of AMT 8000 center unit Extended signal range Avoid installing the amplifier in a distant point from the center unit, otherwise the signal that will be extended will be compromised or even inoperative. Installing the REP 8000 signal amplifier 8. Battery/source The RF REP 8000 range amplifier has an internal 3.7 Vdc rechargeable battery and a capacity of 3,000 mA. The connector for the battery is located on its board (not accessible if the screws are not removed). This battery is used in the event of a power outage, the main power of the amplifier coming from the 7 Vdc/500 mA source that comes with the product. To connect the source to the amplifier, connect at the indicated location and plug the wire into one of the specific openings as shown below. Connection to 7 Vdc/500 mA source Battery 3.7 Vdc/3,000 mAh The RF range amplifier has protection against reverse polarity and short circuit in the battery. The RF Range Amplifier also features protection to prevent battery damage in the event of power grid failure. If the voltage in the battery reaches 2.9 V it will shut off so as not to damage the battery. Warning: in case battery replacement is required, please contact our accredited servi- ce network. 9. Homologation 05326-18-00160 This equipment is not entitled to protection against harmful interference and may not cause interference to duly authorized systems. Warranty term It is expressly stated that this contractual warranty is given subject to the following conditions: Name of customer: Signature of the customer: No. of the invoice: Date of purchase: Model: Serial No: Reseller: 1. All parts and components of the product are under warranty against possible manufacturing defects, which may present, for a period of one (1) year, – comprising 90 (ninety) days of legal warranty and 9 (nine) months of contractual warranty, –, counted from the date of purchase of the product by the Consumer, as stated in the invoice of purchase of the product, which is part of this Term throughout the national territory. This contractual warranty includes the express exchange of products that are defective in manufacture. In case no manufacturing defect is found, but flaw(s) from inappropriate use, the Consumer will bear these expenses. 2. Product installation must be done in accordance with the Product Manual and/or Installation Guide. If your product needs to be installed and configured by a qualified technician, look for a suitable and specialized professional, and the costs of these services are not included in the value of the product. 3. If the defect is found, the Consumer should immediately communicate with the nearest Authorized Service listed by the manufacturer, – only they are authorized to examine and remedy the defect during the warranty period provided herein. If this is not respected, this guarantee will lose its validity, as the violation of the product will be characterized. 4. In the event that the Customer request home care, he/she should refer to the nearest Authorized Service for the technical visit fee. If the need for withdrawal of the product is found, the expenses arising, such as trans- portation and safety to and from the product, are under the responsibility of the Consumer. 5. The warranty will totally lose its validity in the event of any of the following: a) if the defect is not of manu- facture, but caused by the Consumer or by third parties alien to the manufacturer; b) if the damage to the product comes from accidents, claims, agents of nature (lightning, floods, landslides, etc.. ), humidity, mains voltage (overvoltage caused by accidents or excessive mains fluctuations), installation/use in disagreement with the user manual or due to natural wear of parts and components; c) if the product has been influenced by chemical, electromagnetic, electrical or animal (insects, etc.); d) if the product’s serial number has been tampered with or erased; e) if the device has been tampered with. 6. This warranty does not cover loss of data, so it is recommended that the Consumer make a regular backup of the data on the product. 7. Intelbras is not responsible for the installation of this product and also for any attempts of fraud and/or sabo- tage on its products. Keep software and application updates, if any, up to date, as well as network protections necessary to pro¬tect against hackers. The equipment is guaranteed against flaws within its normal conditions of use, and it is important to be aware that, since it is an electronic equipment, it is not free from frauds and scams that may interfere with its correct functioning. 8. This product has an internal battery. After their useful life, the batteries must be delivered to an authorized technical assistance office at Intelbras or directly to the environmentally appropriate final disposal, avoiding environmental impacts and health. If you prefer, the battery, as well as other unused Intelbras electronics, can be disposed of at any Green Eletron collection point (electronic waste manager to which we are associated). In case of doubt about the reverse logistics process, please contact us by phone (48) 2106-0006 or 0800 704 2767 (Monday to Friday from 8 am to 8 pm and on Saturdays from 8 am to 6 pm) or through e -mail [email protected]. Since these are the conditions of this complementary Warranty Term, Intelbras S/A reserves the right to change the general, technical and aesthetic characteristics of its products without prior notice. The manufacturing process for this product is not covered by the requirements of ISO 14001. All images in this manual are illustrative. 01.20 Made in Brazil Customer Support: (48) 2106 0006 Forum: forum.intelbras.com.br Support via chat: intelbras.com.br/suporte-tecnico Support via e-mail: [email protected] Customer Service: 0800 7042767 Where to buy? Who installs it? 0800 7245115 Produced by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira Rodovia BR 459, km 124, nº 1325 – Distrito Industrial – Santa Rita do Sapucaí/MG – 37540-000 CNPJ 82.901.000/0016-03 – www.intelbras.com.br