IntesisBox IBOX-BAC Series Manuals

1 / 2 This information is subject to change without prior notice IntesisBox is a registered trademark of Intesis Software S.L.U. email: [email protected] web: www.intesisbox.com phone: +34 938047134 IBOX-BAC-ROUTER IntesisBox BACnet MS/TP to BACnet IP router Order Code: IBBACRTR0320000 ** stands for the IntesisBox capacity and varies depending on the specific gateway acquired Installation Sheet rev.1.3 Intesis Software SLU © 2019 SAFETY INSTRUCTIONS ! WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and may also damage seriously the gateway and/or any other equipment connected to it. The gateway must be installed by accredited electrician or similar technical personnel, following all the safety instructions given here and in accordance always with the country legislation for installation of electric equipment. The gateway cannot be installed outdoors or exposed to direct solar radiation, water, high relative humidity or dust. The gateway must only be installed in a restricted access location. In case of wall mount, fix firmly the gateway on a not vibrating surface following the instructions next. In case of DIN rail mount fix the gateway properly to the DIN rail following the instructions below. Mounting on DIN rail inside a metallic cabinet properly connected to earth is recommended. Disconnect always power of any wires before manipulating and connecting them to the gateway. A power supply with an NEC Class 2 or Limited Power Source (LPS) and SELV rated is to be used. Respect always the expected polarity of power and communication cables when connecting them to the gateway. Supply always a correct voltage to power gateway, see details of voltage range admitted by the device in the technical characteristics below. CAUTION: The device is to be connected only to networks without routing to the outside plant, all communication ports are considered for indoor only. This device was designed for installation in an enclosure. To avoid electrostatic discharge to the unit in environments with static levels above 4 kV, precautions should be taken when the device is mounted outside an enclosure. When working in an enclosure (ex. making adjustments, setting switches etc.) typical anti-static precautions should be observed before touching the unit. Safety instructions in other languages can be found at: https://www.intesisbox.com/intesis/product/media/v6_safety.pdf INSTALLATION Follow instructions next to properly install the gateway. Disconnect from mains the power supply before connecting it to the gateway. Disconnect power of any bus or communication cable before connecting it to the gateway. Mount the gateway in a vertical position on the wall or DIN rail following the instruction given below, respecting the safety instructions given above. IMPORTANT: Connect a NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply to the gateway, respect the polarity if DC power or Line and Neutral if AC power. This power supply must not be shared with other devices. Apply always a voltage within the range admitted by the gateway and of enough power (see technical characteristics). Circuit-breaker must be used before the power supply. Rating 250V- 6A. Connect the communication cables to the gateway, see details on the user's manual. Power the gateway and the rest of devices connected to it. Wall Mount 1. Separate the fixing clips in the bottom of the box, pushing them to the outside until hear the "click" which indicates that now the clips are in position for wall mount, see in the figure below. 2. Use the holes of the clips to fix the box in the wall using screws. Use the template below for the wall wholes. Clips in their original position Clips in position for wall mount (for DIN rail mount) DIN Rail Mount With the clips of the box in their original position, insert first the box in the upper edge of the DIN rail and later insert the box in the down part of the rail, using a small screwdriver and following the steps in the figure below. DIN Rail 1 2 3 Owner’s Record The model and serial numbers are located on the rear of the gateway. Record these numbers in the space provided below. Refer to them whenever you contact upon your gateway dealer or support team regarding this product. Model No. Serial No. CONFIGURATION Use the Configuration Tool to configure the gateway. See instructions to download and install the latest version at: https://intesisbox.com/intesis/software/intesisbox_maps_installer.exe Use the Ethernet connection for communication between the gateway and the configuration tool. See CONNECTIONS below and follow instructions of user’s manual for more details. Press