Intex 10903 Manuals

PARTS REFERENCE 1 2 3 4 5 6 7 8 9 10 2 5 5 1 26 6 2 2 2 2 2 5 5 1 34 8 2 2 2 2 10815 10810 10809 10824 10349 10348 11004A 11004B 11005A 11005B 10815 10810 10809 10824 10349 10348 10822A 10822B 11006A 11006B 10911 10810 10809 10912 10913 10914 10915A 10915B 10916A 10916B 10911 10810 10809 10912 10913 10914 10917A 10917B 10918A 10918B REF. NO. DESCRIPTION LADDER SIZE & QUANTITY 48” 52” 48” #58974 #58975 #10903 #10904 52” SPARE PART NO. U-SHAPED TOP RAIL SHORT FASTENER FOR U-SHAPED TOP RAIL (WITH 1 EXTRA) LONG FASTENER FOR TOP PLATFORM (WITH 1 EXTRA) TOP PLATFORM STEP MOUNTING PIN (WITH 2 EXTRA) STEP UPPER SIDE LEG (“A” ENGRAVED ON TOP CAP) UPPER SIDE LEG (“B” ENGRAVED ON TOP CAP) LOWER J-SHAPED SIDE LEG (“A” ENGRAVED ON TOP CAP) LOWER J-SHAPED SIDE LEG (“B” ENGRAVED ON TOP CAP) 92IO 92IO (92IO) 48" & 52" 2-SECTIONS POOL LADDER ENGLISH 4.875” X 7.25” 07/17/2006 (92IO) 48" & 52" 2-SECTIONS POOL LADDER ENGLISH 4.875” X 7.25” 07/17/2006 WARNING INTEX® OWNER’S MANUAL - POOL LADDER 48" (122cm) & 52" (132cm) models IMPORTANT SAFETY RULES Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product. • LOCATE THE LADDER ON A SOLID BASE. • ONE PERSON ON THE LADDER AT A TIME TO PREVENT INJURY. • THE LADDER SHALL BE INSTALLED PER MANUFACTURER'S INSTRUCTIONS. • FACE THE LADDER AT ALL TIMES WHEN GETTING IN OR OUT OF POOL. • REMOVE AND SECURE LADDER WHEN POOL IS NOT OCCUPIED TO PREVENT UNAUTHORIZED USE AND POSSIBLE DROWNING. • DO NOT USE THE LADDER FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT WAS INTENDED. • CHECK ALL NUTS AND BOLTS REGULARLY TO ENSURE LADDER STAYS STURDY. • DURING NIGHTTIME POOL USE, ARTIFICIAL LIGHTING SHALL BE USED TO ILLUMINATE ALL SAFETY SIGNS, LADDERS, STEPS AND WALKS. • ALWAYS ENSURE THAT THE LADDER IS USED UNDER CONSTANT ADULT SUPERVISION. • NO DIVING. NO JUMPING. SHALLOW WATER. SAVE THE CARTON FOR STORAGE AND THE INSTRUCTIONS FOR RE-ASSEMBLY 092IO-R0-0707 FOLLOW THESE RULES TO AVOID SERIOUS INJURY OR DROWNING These assembly instructions are the same for the 3-step and 4-step ladders.The assembly drawings show the 4-step ladder. Tools required: One (1) Phillips screwdriver One (1) pair of pliers or a small adjustable wrench IMPORTANT: Do not fully tighten fasteners until last assembly operation. 1. Leg Installation Align the groove and notch, connect the "A" upper legs (7) with the "A" lower legs (9), "B" to "B".Turn the upper leg clockwise to secure. 2. Step Installation The pool ladder legs have the step mounting fixtures installed at the factory. With the arrow on the backside of the step mounting fixture facing up, slip the step (6) onto the mounting fixture, matching the direction of the arrow on the step. Ensure the back of the step is flush with the mounting fixture, otherwise the step will be installed upside-down. IMPORTANT: During assembly, the "A" legs fit into the "A" step holes, and "B" legs into "B". Push the step mounting pins (5) into the holes securing the step in a fixed position. 3. Top platform Installation (One Side at a Time) Look for the "A" identification mark on the top platform (4). Slide the top platform "A" hole onto the "A" leg, "B" to "B". Fasten with fasteners (3) as shown. IMPORTANT: Do not fully tighter fasteners at this time. Follow the illustrations as shown. 4. U-Shaped Top Rail Installation Install the U-Shaped top rails (1) onto the subassembly as shown and connect with fasteners (2). IMPORTANT: During assembly, pushing both sides of the ladder inwards will help slide the U-shaped top rails onto the legs. 5. Final Assembly Fully tighten all fasteners and apply downward pressure to each step to be sure they are fully anchored in place.The ladder is now ready to use! This ladder is designed and manufactured for Intex Pool wall height: Refer back of the manual for Parts Reference. Item # Pool Wall Height 58974 (white & blue) 48" (122 cm) 10903 (silver & white) 48" (122 cm) 58975 (white & blue) 52" (132 cm) 10904 (silver & white) 52" (132 cm)