inVue OneKEY Manuals

OneKEY IR4 Keys, Chargers & OneKEY Manager Section 1: Charger (4 & 8 Position) Installation • Adhesive Mount - Use the povided alcohol wipe to clean the area where the charger will be placed. Allow it to dry completely. 1a CONTENTS: One pad saturated in 75% Isopropyl Alcohol DIRECTIONS: Apply topically as needed to cleanse surface mounting area. FOR EXTERNAL USE ONLY KEEP OUT OF REACH OF CHILDREN KEEP AWAY FROM EYES AND FIRE Determine how the cable will be routed. There are 3 exits on the bot- tom of each charger. 1b Peel the clear film from the adhesives on the bottom of the charger (4 adhesives on the 4 position charger and 6 on the 8 position charger). 1c Route the cable as determined in Step 1b, place the charger where desired and apply pressure for at least 10 seconds. 1d 1 2 3 The cable can also descend down through the fixture if a hole or slot is present. 1c 2b Place the charger onto the screws. Screw Mount - Drill 2 small pilot holes based on the distances (either horizontally or vertically) below that correspond to your charger. • 4 Position Charger - 60mm (2 3/8 in). • 8 Position Charger - 130mm (5 1/8 in). Insert the screws (not provided, choose screws appropriate to the fixture’s material) into the pilot holes. Allow enough of the screw sticking out to hang the charger. 2a 60mm (2 3/8 in) 130mm (5 1/8 in) The LED on the charger will illuminate, indicating that it is receiving power. 4 Place a Key onto the contacts in one of the charger slots. Allow the Key to charge for 6 hours before use. 5 Below is a breakdown of the IR4 Key’s LED indicators. • Green - Battery and Timeout are good for continued use. • Yellow - Return the Key to the Manager within the hour. Battery is low or Timeout is close to expiration. • Red - Return the Key to the Manager immediately. Battery is too low for continued use or the Key has timed out. • No LED - Return the Key to the Manager immediately. Battery is completely depleted. 3 Plug the power cable into a PS515 power supply. Plug the power supply into a power outlet. 7a Section 2: OneKEY Manager Installation Place the OneKEY Manager where desired and plug the PS512 power supply into the port on the back of the Manager. Plug the power supply into a power outlet. If using the Single Key Charger (OK4101), slide the OneKEY into the charger. Ensure that the charging contacts on the OneKEY align with the charging contacts on the charger. 6 There are 2 versions of the OneKEY, here are the differences. Batch Key (OK4000 & OK4000-S) LIVE Key (OK4400, OK4401, OK4406 & OK4500) Activity Tracking Remote Key Deauthorization Parts Needed Batch updates when docked with the OneKEY Manager Real time data transfer over a LORA network No Yes • OneKEY (Batch) • OneKEY Manager & Power Supply • Single, 4x or 8x Charger & Power Supply • LAN Connection • OneKEY (LIVE) • OneKEY Manager & Power Supply • Single, 4x or 8x Charger & Power Supply • LAN Connection • LORA Gateway Plug the network cable into the eth- ernet port on the OneKEY Manager. Follow the screen prompts to set up the OKM Note: If not using Access Manager, it is not necessary to connect the OKM to the internet. 7c The LED on the back of the OneKEY Manager will illuminate, indicating that it is receiving power. 7b 8 Select the Language. Confirm by pressing “Yes”. Note: Not all languages may be supported at the time of launch. Additional languages will be added through periodic updates. Section 3: Enrolling the OneKEY Manager (OKM) in Access Manager Before beginning, ensure that you have a valid InVue Access Manager account and the following information • Your Site URL (for example “https://customer.invue-am.com”) • Your Manager PIN • Your Administrator User Name & Password • Your Adminstrator User Pin • Your OKM Installer Code (not needed if using the OKM without Access Manager). • The TCP port for the OKM If you do not have any of these credetials, please reach out to the InVue Customer Service Team. • NA / LATAM // 704.752.6513 • 888.55.INVUE • EMEA // +31.23.8900150 • APAC // +852.3127.6811 9 Select “Yes” to proceed and enter your OKM Installer Code. Select “No” if not using Access Mananger. 10 10 Enter your OKM Installer Code. 11 11 Select which option best suits your installation • Auto Connect (DHCP) - Best suited for most installations • Manual Connect (Static IP) - Will need to be coordinated between your IT department and InVue Customer Service • Proceed without Connection - Select this is not using Access Manager and not connected via ethernet. 12 12 The OKM will display a connection status screen.