JCM Technologies F30 Manuals

F30 User Manual Table of contents Important safety instructions 3 Important safety instructions for installation 3 Important safety instructions for use 4 Use of the system 4 Introduction 5 General description 5 Detailed description 5 Installation 8 Fixations of the control panel 8 Connections 9 Configuration / Starting up 13 Option 1 selector 13 Option 2 selector 13 Connect the power supply 13 Initialization of inverter parameters 14 Speed ramps adjustment 15 Checking motor direction 16 Programming 16 Manoeuvre programming with digital end limit switch (ENCODER) 16 PROGRAMMING FOR OPENING 16 PROGRAMMING FOR CLOSING 17 Fine adjustment (for programming with absolute encoder) 17 MODIFYING THE “DOOR OPENED” POSITION 17 MODIFYING THE “DOOR CLOSED” POSITION 17 Manoeuvre programming with limit switches 18 PROGRAMMING FOR OPENING 18 PROGRAMMING FOR CLOSING 18 Partial manoeuvre programming 18 Verification 18 Verify that the control panel works correctly 18 Safety edge 18 Photocell 18 Communication’s quality (in case of RSEC3 connected) 18 Maintenance 19 Fuse replacement 19 Set parameters to default values 19 Warning of maintenance 19 Troubleshooting 20 F30 20 Indicator light for possible faults, LED ERROR 21 Technical Data 22 Electrical Parameter 22 Notes 23 Regulatory Data 24 jcmtechnologies 2 EU Declaration of conformity 24 Important safety instructions Important safety instructions for installation Disconnect the power supply whenever you proceed to the installation, main- tenance or repair of the equipment. •Before installing the panel, remove all unnecessary ropes or chains and disable any equipment such as locks that is not necessary for the automatic operation. •Before installing the panel, check that the door is in good mechanical condition, correctly balanced and that it opens and closes correctly. •Install the manual unlocking device at a height lower than 1.8m. •Install any permanent control next to the door away from any moving part and at a minimum height of 1.5m. •For permanently connected equipment, an easily accessible power disconnection device must be incorporated into the wiring. It is recommended that this be of the emergency switch type. •If the control panel is supplied without emergency stop button, this will be incorporated in the installation, connecting it to the STOP terminal. •For correct use of the security edge, this must never be activated when the door is fully closed. It is wise to install the ends of run before activating the edge. •This equipment can only be handled by a specialist fitter, by maintenance staff or by a suitably trained operator. •To connect the power supply and motor wiring, 2.5 mm2 section terminals must be used. •Use protective goggles when handling the equipment. •Fuses must only be handled when the appliance is disconnected from the mains. •The instructions for using this equipment must remain in the possession of the user. •European door normative EN 12453 and EN 12445 specify the following minimum protection and door safety levels: - for single-family dwellings, prevent the door from making contact with any object or limit the force of contact (e.g. safety band), and in the case of automatic closing, it is necessary to complement this with a presence detector (e.g. photocell). - for communal and public installations, prevent the door from making contact with any object or limit the force of contact (e.g. safety band), and complement this with a presence detector (e.g. Photocell). F30 control panel switches automatically to dead man mode when safety devices are active or defective. Therefore, all controls work as “hold-to-run” controls. WARNING: IN ACCORDANCE WITH THE EN 13241-1 AND EN 12453-1 STANDARD CONCERNING PRESSURE MAINTAINED CONTROL DEVICES: “The person operating the door must have a direct view of the doorway, must be near the door (5 meters maximum) during movement of the door and should not find itself in a dangerous position”. Any adjustment of the radio range out of these recommendations, undertakes the installer in terms of responsibility for injury or damage. “Releasing of the pressure maintained control device should stop the door movement before it scrolls 5cml”. jcmtechnologies 3