JL Audio Stealthbox SB-N-350/10W3v2 Manuals

➔ ➔ ➔ ➔ Stealthbox ® I N S T A L L A T I O N G U I D E SB-N-350/10W3v2, JL AUDIO, Inc 2004 Sheet SKU#011187 Revision 2/11/2004 Page 1 for the SB-N-350/10W3v2 (2003-Up 350Z, Will not fit the 350z Roadster, Infiniti G35 Coupe & Sedans) This Stealthbox is a product which requires professional installation skills and tools. Please read this installation guide thor- oughly before beginning the project. It will guide you step by step through the installation. Several of the steps in this process may require two people to accomplish. It is absolutely vital that the enclosure be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly pres- ents two problems: 1) The sub-bass performance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s) and 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration. Please enjoy your JL Audio Stealthbox responsibly. STEP 1: Remove all contents from center console, rear cargo area, rear glove box com- partments, lastly slide and tilt the seats to the front of the car. STEP 3: Remove the driver’s side and pas- senger’s side door sill panels. *Carefully pulling directly upward.* STEP 2: Remove the driver’s side and pas- senger’s side rear interior cargo quarter pan- els. STEP 4: Remove the Philip head screws, that are found on both diver’s side and passen- ger’s side of the console. STEP 5: Remove the two Philip head screws that have been exposed by the removal of the ashtray. START HERE Continued on Next Page ➔ w w w . j l a u d i o . c o m ➔ ➔ STEP 6: Loosen the shifter trim panel by pulling directly up. Pull the panel away from the console. Manual transmission shifter shown in picture, auto- matic shifter removal maybe slightly different, then shown. *Careful not to damage the shifter or scratch the dash panel. * ➔ ➔ ➔ ➔ ➔ STEP 10: Lift at the rear of the console and care- fully pull unit over the emergency hand brake arm. Cont. From Previous Page Continued on Next Page ➔ ➔ STEP 7: Disconnect the white wiring plug at the rear of the A/C controls. STEP 11: Disconnect the wiring harness at the plug located under the center console. ➔ STEP 12: Carefully guide the shifter boot trim panel through the front opening in the console.This will allow for full removal of the center console. *Careful not to damage the shifter boot or scratch the dash panel. * STEP 13: Remove the center console, out of the vehcile. STEP 8: With the shifter trim panel moved to one side. Remove the pair of Philip head screws at the front edge of the console. STEP 9: Engage the emergency brake, by pulling up on the handle. SB-N-350/10W3v2, JL AUDIO, Inc 2004 Sheet SKU#011187 Revision 2/11/2004 Page 2 w w w . j l a u d i o . c o m STEP 14: Remove the rear bulkhead front panel, by carefully pulling towards the front of the vehcile around the glove box. ➔ ➔ ➔ ➔ ➔ STEP 18: Pull back the carpet in the front section of the cargo area to reveal the metal floor. Remove the child seat anchor hooks, reinstall factory bolts without hook. Locate the existing holes(behind the driver’s side and passenger’s side seat), to be used to mount the Stealthbox. Identified by the white circle. Cont. From Previous Page Continued on Next Page ➔ ➔ STEP 16: Remove the pair of 10mm head bolts at the rear of the glove box. STEP 19: Cut the carpet to create a flap that can be folded to allow access to the mounting holes. ➔ STEP 20: If the vehicle is so equipped, fold back floor mat as shown to access the mounting bolts. STEP 22: At this time, attach the speaker wire from the amp to the Stealthbox’s terminal. *Check for proper operation of the woofers.* STEP 17: Remove the numerous 10mm head bolts securing the front edge of the glove box liner. SB-N-350/10W3v2, JL AUDIO, Inc 2004 Sheet SKU#011187 Revision 2/11/2004 Page 3 w w w . j l a u d i o . c o m STEP 15: Remove the pair of Philip head screws securing the passenger side glove box’s door latch. Repeat this STEPfor the driver’s side, if equipped with the glove box. Remove the fac- tory woofer on the driver’s side, if equipped. STEP 21: Thread in the supplied pair of socket cup set screws. Leaving about 1.5” exposed. ➔ ➔ ➔