JVC KD-R210 Manuals

1– EN ENGLISH ESPAÑOL INFORMATION (For U.S.A.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. Caution Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. IMPORTANT FOR LASER PRODUCTS 1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT. KD-R210 CD RECEIVER: INSTRUCTIONS/INSTALLATION GET0621-001A [J] 0809DTSMDTJEIN EN © 2009 Victor Company of Japan, Limited For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No. Warning If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident. Caution on volume setting Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level. – There are improper recording conditions (missing data, etc.) or media conditions (stained, scratched, warped, etc.). • CD-RWs may require a longer readout time since the reflectance of CD-RWs is lower than that of regular CDs. Playing an MP3/WMA disc • This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower). • This unit can show the names of albums, artists (performer), and tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for MP3 files and for WMA files. • This unit can display only one-byte characters. No other characters can be correctly displayed. • This unit can play back MP3/WMA files meeting the conditions below: – Bit rate: 8 kbps — 320 kbps – Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) – Disc format: ISO 9660 Level 1/ Level 2, Romeo, Joliet, Windows long file name • The maximum number of characters for file/folder names vary depending on the disc format used (includes 4 extension characters—<.mp3> or <.wma>). – ISO 9660 Level 1: up to 12 characters; ISO 9660 Level 2: up to 31 characters; Romeo: up to 64 characters; Joliet: up to 32 characters; Windows long file name: up to 126 characters • This unit can recognize a total of 512 files, 255 folders, and 8 hierarchical levels. • This unit can play back files recorded in VBR (variable bit rate). Files recorded in VBR have a discrepancy in the elapsed time display, and do not show the actual elapsed time. In particular, this difference becomes noticeable after performing the search function. • This unit cannot play back the following files: – MP3 files encoded in: MP3i and MP3 PRO format, in an inappropriate format, layer 1/2. – WMA files: encoded in lossless, professional, and voice format; not based upon Windows Media® Audio; copy- protected with DRM. – Files which have data such as WAVE, ATRAC3, etc. • The search function works but search speed is not constant. Basic operations • By pressing SRC on the unit, you can also turn on the power. If the source is ready, playback also starts. • If you turn off the power while listening to a disc, disc play will start from where it had been stopped previously next time you turn on the power. • When no disc is loaded in the unit, you cannot select “CD” as the playback source. Tuner operations • During SSM search... – All previously stored stations are erased and the stations are stored anew. – Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency). – When SSM is over, the station stored in No. 1 will be automatically tuned in. Disc operations Caution for DualDisc playback • The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended. General • This unit has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA) and MP3/WMA formats. • After ejecting a disc, “NO DISC” appears and you cannot operate some of the buttons. Insert another disc or press SRC to select another playback source. Playing a CD-R or CD-RW • Use only “finalized” CD-Rs or CD-RWs. • This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing. • Some CD-Rs or CD-RWs may not be played back on this unit: – Discs are dirty or scratched. – Moisture condensation has occurred on the lens inside the unit. – The pickup lens inside the unit is dirty. – The files on the CD-R/CD-RW are written using the “Packet Write” method. MORE ABOUT THIS UNIT For safety... • Do not raise the volume level too much, as this will block outside sounds, making driving dangerous. • Stop the car before performing any complicated operations. Temperature inside the car... If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit. Attaching the control panel Detaching the control panel How to reset your unit Reset the unit after installation is complete. • Your preset adjustments will also be erased. How to forcibly eject a disc • Be careful not to drop the disc when it ejects. • If this does not work, reset your unit. PREPARATIONS Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. Installation/connection are explained at the last section of this manual (reverse page, indicated with symbol). [European Union only] CANCELING THE DISPLAY DEMONSTRATIONS Turn on the power. Select “DEMO OFF.” Finish the procedure. SETTING THE CLOCK Turn on the power. Select “CLOCK H.” Adjust the hour. Select “CLOCK M.” Adjust the minute. Finish the procedure. (Initial setting) (Initial setting) PREPARING THE REMOTE CONTROLLER (RM-RK50) When you use remote controller for the first time... For USA-California Only: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate If the effectiveness of the remote controller decreases, replace the battery. Warning: To prevent accidents and damage • Do not install any battery other than CR2025 or its equivalent. • Store out of reach of children. • Do not recharge, short, or dismantle. • Do not dispose of in fire. • Do not carry around with other metallic materials. Caution: • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Battery shall not be exposed to excessive heat such as sunshine, fire, or the like. Replacing the lithium coin battery Insulation sheet

Detaching the control panel Attaching the control panel 0809DTSMDTJEIN EN © 2009 Victor Company of Japan, Limited Model No. Serial No. For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom ofthe cabinet. Retain this information for future reference. Thank you for purchasing alVC product. Please read all instructions carefully before operation, to ensure your compiete understanding and to obtain the best possible performance from the unit. Installation/connection are explained at the last section ofthis manual (reverse page, indicated with ~symbol). How to reset your unit Reset the unit after installation is complete. GET0621-001 A [J] ~ Select "DEMO OFF." \YITurnl _liBt. a Finish the procedure. m WMA MP3 KD-R210 CD RECEIVER: INSTRUCTIONS/INSTALLATION ~.Q (Initial setting) _kIMi; f)~d) o Turn on the power. JVC ~- CANCELING THE DISPLAYDEMO~N~ST:JfA::;J:.l. ~:::====-""'P"':'R::EP"A:-RA-:T"IO"NS---~=:::=====- ~~~$, 9 Warning: To prevent accidents and damage • Do not install any battery other than CR2025 or its equivalent. • Store out of reach of children. Do not recharge, short, or dismantle. Do not dispose of in fire. Do not carry around with other metallic materials. Ifthe effectiveness ofthe remote controller decreases, replace the battery. Replacing the lithium coin battery - There are improper recording conditions (missing data, etc.) or media conditions (stained, scratched, warped, etc.). • CD-RWs may require alonger readout time since the refiectance of CD-RWs is lower than that of regular CDs. Playing an MP3IWMA disc • This unit can play back MP3IWMA files with the extension code <.mp3> or <.wma> (regardless ofthe letter case-upper/lower). • This unit can show the names of albums, artists (performer), and tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for MP3 files and for WMA files. • This unit can display only one-byte characters. No other characters can be correctly displayed. • This unit can play back MP3/WMA files meeting the conditions below: - Bit rate: Bkbps - 320 kbps - Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) - Disc format: ISO 9660 Level 11 Levei 2, Romeo, Joliet, Windows long file name • The maximum number ofcharacters for file/folder names vary depending on the disc format used (includes 4 extension characters-<.mp3> or <.wma». - ISO 9660 Levell: up to 12 characters; ISO 9660 Level 2: up to 31characters; Romeo: up to 64 characters; Joliet: up to 32 characters; Windows long file name: up to 126 characters • This unit can recognize atotal of 512 files, 255 folders, and 8hierarchicalleveis. • This unit can play back files recorded in VBR (variable bit rate). Files recorded in VBR have adiscrepancy in the elapsed time display, and do not show the actual eiapsed time. In particular, this difference becomes noticeable after performing the search function. • This unit cannot play back the foHowing files: - MP3 files encoded in: MP3i and MP3 PRO format, in an inappropriate format, layer 1/2. ~ WMA files: encoded in lossless, professional, and voice format; not based upon Windows Media" Audio; copy- protected with DRM. - Files which have data such as WAVE, ATRACJ, etc. • The search function works but search speed is not constant. How to forcibly eject a disc ~[H~d10 • Becorefulnot to drop the disc when itejects. • IIthis does not work, resetyour unit. • Your preset odjustments willo/so be erased. For USA-California Only: This product contains aCR Coin Cell lithium Battery which contains Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate III Tuner operations • During SSM search... - All previously stored stations are erased and the stations are stored anew. - Received stations are preset in No.1 (iowest frequency) to NO.6 (highest frequency). - When SSM is over, the station stored in NO.1 wiIi be automatically tuned in. PREPARING THE REMOTE CONTROLLi,IJl When you use remote controller for the first time... ,""","",","~fffJP MORE ABOUT THIS UNIT • Basic operations • By pressing SRC on the unit, you can also turn on the power. Ifthe source is ready, playback also starts. • If you turn offthe power while listening to adisc, disc play will start from where it had been stopped previously next time you turn on the power. • When no disc is loaded in the unit, you cannot select "CD" as the playback source. Caution: • Danger of explosion if battery is incorrectly replaced. Repiace only with the same or equivalent type. • Battery shall not be exposed to excessive heat such as sunshine, fire, or the like. II Disc operations Caution for DualDisc playback • The Non-DVD side ofa"DualDisc" does not comply with the "Compact Disc Digital Audio" standard. Therefore, the use of Non-DVD side of aDualDisc on this product may not be recommended. General • This unit has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA) and MP3IWMA formats. • After ejecting adisc, "NO DISC" appears and you cannot operate some ofthe buttons. Insert another disc or press SRC to select another playback source. Playing a CD-R or CD-RW • Use only "finalized" CD-Rs or CD-RWs. • This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing. Some CD-Rs or CD-RWs may not be played back on this unit: - Discs are dirty or scratched. - Moisture condensation has occurred on the lens inside the unit. - The pickup lens inside the unit is dirty. - The files on the CD-R/CD-RW are written using the "Packet Write" method. o Finish the procedure. I:l Select "CLOCK M:' <>00= hM- Q Adjusllhe minute. Warning If you need to operate the unit while driving, be sure to look around carefully or you may be involved in atraffic accident. Caution on volume setting Discs produce very little noise compared with other sources. Lower the volume before playing adisc to avoid damaging the speakers by the sudden increase ofthe output level. (Initial setting) Wk&UW (YITUrnJ SETTING THE CLOCK f)~dJ ~ Select "CLOCK H:' <.;:~Oo 'AUtW a Adjust the hour. o Turn on the power. ~ INFORMATION (For US,A.) This equipment has been tested and found to comply with the limits for aClass Bdigital device, pursuant to Part 15 of the FCC Ruies. These limits are designed to provide reasonable protection against harmfui interference in aresidential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in aparticular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more ofthe following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the eqUipment into an outlet on acircuit different from that to which the receiver is connected. - Consult the deaier or an experienced radiofTV technician for help. Caution Changes or modifications not approved by JVC could void the user's authority to operate the equipment. CAUTION ATTENTION AVISO VARNING ;:11: CAunON VISIBLE ANOIO~ RAYONNEldENT LASER AAOlACION LASER smUG OCHIEl:lER ::.tl