Kaboodle 2x11L Side Mount Pullout Bin Manuals

M5 16mm screws x 4 Tools you will need To put your kaboodle kitchen waste bins together you will need the following tools. Hardware included 14mm wood screws x 4 E F C I D J B H A G Cordless drill with: • Number 2 screw tip • 2mm drill bit Tape measure Adjustable square Clamps (optional) Spirit level (optional) Screw driver Safety gear Pencil M5 8mm screws x 2 p. 1 Ver. 2 W-50530 Things you need to know M6 16mm screws x 2 Follow these instructions to install your parts and accessories. • Always read the full instructions prior to installation. • Consider possible obstructions to your parts & accessories, like hinges inside the cabinet or adjacent cabinet doors and handles, prior to installation. • Make sure you leave plumbing and electrical work to qualified trades people. Never try this yourself. • Make sure you always use safety gear like a mask, ear muffs and glasses when using tools. • Tip: After marking out the pre-drill holes as per the instructions, take the part that is to be installed and align the appropriate holes with the markings to ensure they match up prior to pre-drilling the holes. • If you have any questions, contact us on: Australia: 1800 666 078 Monday to Friday between 8:00am and 6:00pm AEST, New Zealand: 0800 522 663 Monday to Friday between 8:00am and 5:00pm NZST or email: [email protected]. 2x11L side mount pullout bin step 2 runners x 1 pair m4 8mm screws x 4 door brackets x 2 bin frame x 1 16mm wood screws x 12 lid brackets x 2 installation guide hardware key kaboodle.com.au A AB step 2 p. 2 Ver. 2 W-50530 1. 343mm 295mm 295mm 343mm 133mm 133mm 229mm 229mm 341mm 341mm 37mm 37mm 235mm 235mm 393mm 393mm 16mm wood screws runners pre-drilling for runners separating runners attaching runners pre-drilling for lid brackets 3. 2. 4. 2 x 11L side mount pullout bin A A B On both sides of your cabinet, draw a horizontal line 343mm up from the bottom. Measuring from the front of the cabinet along these lines, mark out the pre-drill holes at 133mm, 229mm and 341mm as pictured above. Use a 2mm drill bit to pre-drill holes to a depth of roughly 2.5mm. Separate each runner (A) into two parts by extending the guide (i) and pushing up on the lever (ii) while continuing to pull apart the two components. The guide should separate easily from the runner without too much force being applied. Using the lower sets of pre-drilled holes, align with the holes on the runners (A) and fix to the cabinet using 6 x 16mm wood screws (B) as pictured above. On both sides of your cabinet, draw a horizontal line 295mm up from the bottom. Measuring from the front of the cabinet along these lines, mark out the pre-drill holes at 37mm, 235mm and 393mm as pictured above. Use a 2mm drill bit to pre-drill holes to a depth of roughly 2.5mm. (ii) (i) hardware key kaboodle.com.au A B D C E lid brackets m4 8mm screws 16mm wood screws bin frame step 2 p. 3 Ver. 2 W-50530 attaching bin frame inserting bin lid 7. 8. E D Place the bin frame (D) carefully onto the extended runners, aligning the holes and then securing into place with the 4 x M4 8mm screws (E). Note: Support the runners from underneath when screwing the frame into place. Do not tighten screws. reassembling runners attaching lid brackets 5. 6. B C Using the top sets of pre-drilled holes, align with the 2nd, 5th and 7th holes on the lid brackets (C) and fix to the cabinet using 6 x 16mm wood screws (B) as pictured above. 2 x 11L side mount pullout bin Carefully slide the guide back into the runner. The runners should open and close smoothly if assembled correctly. Extend the runners once they have been correctly reassembled. Slide the back plastic catches of the bin lid along the top of the lid brackets until both plastic catches fall into the channels at the back. The front two plastic catches should fit into the front channels at the same time. hardware key A F H G I J H 14mm wood screws door brackets G I J J m5 8mm screws m5 16mm screws m6 16mm wood screws p. 4 Ver. 2 W-50530 step 2 attaching door panel adjusting door panel 11. 12. (ii) (i) attaching door brackets 9. 10. Align each door mount bracket (F) with the pre-drilled holes and fix to the door panel using 4 x 14mm wood screws (G) as pictured above. Ensure the open side of the bracket faces inward and that the height adjustment screw hole is facing down. Half screw the 2 x M6 16mm screws (H) into the height adjustment holes of the door mount brackets as pictured above. Mark out and pre-drill four holes on the inner side of your cabinet door as pictured above. Use a 2mm drill bit to pre-drill holes to a depth of roughly 2.5mm. 2 x 11L side mount pullout bin 37mm 37mm 195mm 195mm 291mm 291mm F H Slide the door mount brackets onto the runner brackets (i), ensuring the height adjustment screws (H) slip into the notches (ii). Screw through the top and bottom holes of the runner brackets, ensuring they are as centred as possible, using 4 x M5 16mm screws (J). Next attach the 2 x M5 8mm screws (I) through the middle holes of each runner bracket. pre-drilling for door brackets If required, you can now adjust the door panel by tightening or loosening the screws as pictured above. Once door is aligned, tighten the four screws that secure the bin frame to the runners.