Kenwood KCH-20R Manuals

SERVICE MANUAL COPYRIGHT © 2015 JVC KENWOOD Corporation No.RA027 2015/6 B5B-7206-00 REMOTE CONTROL HEAD RA027 2015 6SERVICE MANUAL B5B-7206-00 KCH-20R COPYRIGHT © 2015 JVC KENWOOD Corporation TABLE OF CONTENTS 1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13 4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13 5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14 This product complies with the RoHS directive for the European market. This product uses Lead Free solder. 1-2 (No.RA027) Document Copyrights Copyright 2015 by JVC KENWOOD Corporation. All rights reserved. No part of this manual may be reproduced, translated, distributed, or transmitted in any form or by any means, electronic, mechan- ical, photocopying, recording, or otherwise, for any purpose without the prior written permission of JVC KENWOOD Corporation. Disclaimer While every precaution has been taken in the preparation of this manual, JVC KENWOOD Corporation assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. JVC KENWOOD Corporation reserves the right to make changes to any products herein at any time for improvement purposes. Bluetooth Copyrights The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under licence. Other trademarks and trade names are those of their respective owners. SECTION 1 PRECAUTION This service manual does not describe PRECAUTION. R (No.RA027)1-3 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS 2.1 INSTALLATION 2.1.1 Installing the Remote control head (KCH-20R) The KCH-20R control head is used to remotely operate the NX-5700/5800 series transceiver. The KCH-20R is connected to the KCT-71 remote control cable. The KRK-15B is connected to the NX-5700/5800 RF Deck with the KCT-71. 2.1.2 Connection image 2.1.3 DIP Switch setting All DIP switches for single remote (KCH-20R and KRK-15B) must be set as "ON". 2.1.4 Remove the Operation panel from the transceiver (NX-5700, NX-5800 only) (1) Lift the two tabs of the panel on the bottom of the transceiv- er with a flat-head screwdriver and remove the panel from the chassis. (Fig. 1) Fig.1 (2) Remove the flat cable from the display unit connector (CN6) of the panel. (3) Remove the cable from the display unit connector (CN2) of the panel. 2.1.5 Install the KRK-15B onto the NX-5700, NX-5800 RF Deck (1) Insert the cable into the interface unit (XC3-0090-20) con- nector (CN2) of the KRK-15B. (2) Insert the flat cable into the interface unit connector (CN1) of the KRK-15B. (Fig. 2) Fig.2 Note: The blue line of the flat cable and the flap of connector are as same side. After inserting, the flat cable should be locked with the connector (flap) surely. (3) Fit the KRK-15B with four tabs onto the front of the chassis. (Fig. 3) Fig.3 Note: When installing the KRK-15B onto the front of the chas- sis, hold down the flat cable with your fingers to prevent it from being caught. NX-5700/5800 RF Deck KCT-71 Remote Control Cable KRK-15B Featured Panel KCH-20R KCT-72 Connection Cable KCH-20R 1 2 3 4 ON KRK-15B 1 2 3 4 ON KRK-15B CN1 CN2 RF Deck 1-4 (No.RA027) 2.1.6 Connect the KRK-15B and KCH-20R with the KCT-71 (1) Insert one lead wire with connector of the KCT-71 into the connector (CN3) of the KRK-15B. (Fig. 4) Fig.4 (2) Secure the cable bush as shown in the figure 5 and attach the waterproof packing. Note: There is a direction to the installing of the cable bush. Fig.5 (3) Slide the molding cover so as not to float the waterproof packing and attach so that it is locked. (Fig. 6) Fig.6 (4) Insert the other lead wire with connector of the KCT-71 into the connector (CN5) of the KCH-20R.(Fig. 7) Fig.7 (5) Attach the waterproof packing and molding cover in the same way of step 2 and 3.(Fig. 8) (Fig. 9) Fig.8 Fig.9 KCT-71 lead wire with connector KRK-15B CN3 Waterproof Packing Cable Bush Molding Cover KCH-20R KCT-71 lead wire with connector CN5

B5A‑0605-00 USER MANUAL MODE D’EMPLOI MANUAL DEL USUARIO KCH-20R USER MANUAL REMOTE CONTROL HEAD KCH-20R • SDTM and microSDTM are trademarks of SD-3C, LLC in the United States. and/ or other countries. • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. Firmware Copyrights The title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVC KENWOOD Corporation. 2 PRECAUTIONS • Do not disassemble or modify the unit for any reason. • Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances. • Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces. • If you detect an abnormal odor or smoke coming from the unit, disconnect the power from the unit immediately. Contact your KENWOOD service center or dealer. • Do not attempt to configure the transceiver while driving; it is too dangerous. • Do not use options not specified by KENWOOD. • For passenger safety, install the unit securely using the supplied mounting bracket and screw set so the unit will not break loose in the event of a collision. • Always turn off the power before installing optional accessories. • When using the KCH-20R, refer to the “NOTICES TO THE USER” and “PRECAUTIONS” in the USER GUIDE of Mobile Transceiver of NX-5000 series. If the warnings ( ) are not observed, there may be the possibility to have any malfunction. In this case, press and hold the Power Switch for 5 seconds or more. If the malfunction persists, ask your dealer. SUPPLIED ACCESSORIES a Mounting bracket...........................................................................................................1 b Mounting screw..............................................................................................................2 c Screw set (5 x 16 mm self-tapping screw x 4, Spring washer x 4, Flat washer x 4).....1 d Microphone cable holder................................................................................................1 e Pan head sems screw (M3 x 8 mm)..............................................................................1 f PF name plates (the A, B and C name plate has been attached).................................1 a b d e c f e d Microphone cable 3 REPLACING THE PF NAME PLATE You can reconfigure the PF name plates at any time. 1 Remove the current PF name plate from the function key using a fine-tipped tool. 2 Punch out the PF name plate card, and insert the plate onto the relative function key. Name plate Squeeze and insert the plate INSTALLING THE microSD MEMORY CARD 1 Open the Cap. 2 Insert the microSD memory card. • Insert the microSD memory card with its terminal side facing the same side as the front of the panel. • Insert the microSD memory card until it clicks into place. • To remove the microSD memory card, push the card inwards once, then pull it out straight. Cap microSD memory card Note: ◆ ◆microSD memory cards (Class 2 or higher) and microSDHC memory cards (Class 2 or higher) can be used. ◆ ◆SDXC memory cards cannot be used. ◆ ◆This transceiver is not guaranteed to operate with all microSD memory cards. (Operations are confirmed on memory cards for the following brands: SanDisk, TOSHIBA and Panasonic.) ◆ ◆Use the microSD memory card within the allowable operating temperature. ◆ ◆Do not remove the microSD memory card or turn off this transceiver while the microSD memory card is being accessed. ◆ ◆The waterproof performance is not guaranteed if the microSD memory card slot cap is not fit into place. ◆ ◆Make sure your hands are clean before opening the microSD memory card slot cap. Compensation Disclaimer Data stored on the microSD memory card may be altered or lost due to problems with this transceiver. We do not accept liability in respect of the data stored on your microSD memory card, failure to save the data properly, loss of data, and any direct or indirect damages.