Key Digital KD-DA2x4G Manuals

1 2 3 3 6 6 7 5 4 1 2 3 3 6 6 7 5 4 1 2 3 3 6 6 7 5 4 2x4/2x8 4K/18G POH/HDBT/HDMI Distribution Amplifier/ Switcher with Audio De-Embedding (Includes KIT 4/8Rx 100 Meters Extenders) QUICK SETUP GUIDE KD-DA2x4G / KD-DA2x8G CONNECT Begin with the KD-DA2x4G/KD-DA2x8G unit and all input/output devices turned OFF. © 2018 Key Digital, Inc. All rights reserved. READ PRIOR TO INSTALLATION 1. Connect HDMI sources to the input ports of KD-DA2x4G/KD-DA2x8G unit 2. Connect HDMI displays to the output ports of KD-XDALRx units 3. Connect CAT wires from KD-DA2x4G/KD-DA2x8G’s HDBaseT outputs to KD-XDALRx HDBaseT input. 4. Connect analog or digital audio outputs to audio system 5. Connect control system and/or PC to TCP/IP, RS-232, or place IR emitter over IR sensor. 6. To control connected monitors, connect IR/RS-232 pass-thru wiring from control system into pass-thru ports and from KD-XDALRx to controlling displays 7. Screw-in both power supplies to the KD-DA2x4G/KD-DA2x8G’s unit, and then connect power to outlets. 8. Power on HDMI sources and displays Open the KDMS™ Pro software and perform a network scan (fig. 1) 2 If using KD-App or KDMS™ for control, set the desired Input/Output names by entering the Input/Output Settings section of the properties window, and selecting the Change Input/Output Name button (fig. 4a), selecting the desired input/output and entering the name (fig. 4b) Additional settings may be adjusted in the KDMS software. Full access to all settings/ commands is achieved via terminal session using Tera Term or PuTTy software. 4 Option 1: Control via Remote Control › Switching – Use Input button Option 2: Control via KD-App, or Key Digital Management Software™ (KDMS™) KD-DA2x4G/KD-DA2x8G are controllable by: 1. Key Digital’s user-friendly iOS App (FREE Download on the App Store: https://goo.gl/k5SDyM ) or 2. Key Digital Management Software™ Pro (Key Digital website: https://goo.gl/Kge2LH ). Configuration Steps: » Connect and Configure you KD-DA2x4G/KD-DA2x8G as described in this Quick Setup Guide. » Download and open KD-App and/or KDMS™ » Ensure the iOS device and/or PC computer are on the same network with KD-DA2x4G/KD-DA2x8G » Perform a network scan in the KD-App/KDMS™ » Select and control the selected KD-DA2x4G/KD-DA2x8G » If desired, the KD-App allows users to create presets for KD-DA2x4G/KD-DA2x8G’s current input-output selections. 1 2 3 Connect to your unit via TCP/IP port using default static IP address 192.168.1.239, port 23 to a 192.168.1.xxx type network or set your PC to a static IP address of 192.168.1.xxx (excluding .239). 1 CONFIGURE Configure and control your KD-DA2x4G/KD-DA2x8G units via Key Digital Management Software™ Pro (KDMS™ Pro) that can be downloaded here: https://goo.gl/ZcyHui CONTROL Your unit is now ready to control from the KDMS™ Control Panel, KD-App, or by professional control system. Key Digital ® App on the App Store Key Digital ® App on the App Store KDMS™ Pro Download Page Key Digital ® App on the App Store KDMS™ Pro Download Page KDMS™ Download Page a. Choose the detected device from the Devices window (fig. 2a) b. In the Network Settings section of the Properties window, enter the desired IP settings (fig. 2b) c. Save (fig. 2c) › IP Address (default is 192.168.1.239) › Subnet Mask (default is 255.255.255.0) › Gateway (default is 192.168.1.1) › Port (default is 23) Default static IP address: 192.168.1.239, port 23 KD-DA2x4G KD-DA2x8G Visit product pages for most recent version of the manual, quick setup guide, firmware, control drivers and all additional downloads. Key Digital® • 521 East 3rd Street, Mount Vernon, NY 10553 Phone: 914.667.9700 • Fax: 914.668.8666 • www.keydigital.com CONTROL Option 3: Control via professional control system KD-DA2x4G/KD-DA2x8G allows control over serial interface for bi-directional communication. Default static IP address: 192.168.1.239, port 23 Pin: 1 2 3 Connection Protocol: › Baud Rate = 57,600 bits per second › Data Bits = 8 › Stop Bits = 1 › Parity = Non › Flow Control = None › Carriage Return: Required at end of string › For RS-232 control use pins 1, 2, and 3 of the Main Control port. › For TCP/IP control, the default IP address is 192.168.1.239, with port 23 › Most Key Digital matrix switches support a standard audio+video switching command. KD-DA2x4G/KD-DA2x8G is also controllable by this command, so if you have previously integrated Key Digital matrixes by third-party control systems you may have success using the same driver/module. Switching – Video + Audio together (two commands supported) SPO01SIyy yy = input number (01-02) SPOSIyy yy = input number (01-02) 3 Rev 0 – Dec 2018 IMPORTANT PRODUCT WARNINGS › Connect all cables before providing power to the unit. › Test for proper operation before securing unit behind walls or in hard to access spaces. › You MUST use the Power Supply provided with your unit or you VOID the Key Digital® Warranty and risk damage to your unit and associated equipment. (CONTINUED)

2x4/2x8 4K/18G POH/HDBT/HDMI Distribution Amplifier/Switcher with Audio De-Embedding (Includes KIT 4/8 Rx 100 Meters Extenders) Operating Instructions KD-DA2x4G KD-DA2x8G KD-DA2x4G KD-DA2x8G Default static IP address: 192.168.1.239, port 23 2 Table of Contents About KD-DA2x4G/KD-DA2x8G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connections, Buttons and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 EDID Handshaking Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Auto Sensing Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Extending IR and RS-232 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 RS-232 and TCP/IP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Important Product Warnings & Safety Instructions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 How to Contact Key Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 ›› Note: Please visit www.keydigital.com for the latest product documentation and software downloads. Product features and specifications are subject to change without notice. © 2019 Key Digital, Inc. All rights reserved. Always follow the instructions provided in this Operating Manual. KD-DA2x4G KD-DA2x8G Visit product pages for most recent version of the manual, quick setup guide, firmware, control drivers and all additional downloads. 1 About KD-DA2x4G/KD-DA2x8G Key Digital’s KD-DA2x4G and KD-DA2x8G are 18Gbps and HDCP2.2 supporting HDMI Switcher + Distribution Amplifier kits with HDBaseT output and 4/8 Rx units included. The KD-DA2x4G/KD-DA2x8G kit is designed for applications such as Digital Signage and other professional AV installation types, where the selected HDMI source is distributed to up to 4/8 displays. All connected displays show the same image at the same time. The 4/8 KD-XDALRx HDBaseT Rx extenders are all powered via HDBaseT from the KD-DA2x4G/2x8G unit, and support extension of resolutions up to UHD/4K up to 250 ft. (76m) using CAT5e/CAT6/CAT6A/CAT7. 1080p resolutions may be extended up to 328 ft. (100m). KD-DA2x4G/KD-DA2x8G is easily integrated into professional AV systems with the audio from the selected source being de-embedded on analog and digital audio connectors, and switching controllable via TCP/IP, RS-232 or IR. KD-DA2x4G/KD-DA2x8G is Key Digital App ready and also controllable by control systems such as Compass Control Pro. EDID handshaking is easily selected via front panel rotary dial and all UHD/4K EDID handshake files include HDR header information. Key Features ›› HDMI Switching & Distribution: 2 HDMI sources to 4/8 HDBaseT outputs ›› Power over HDBaseT: All included Rx units powered by the main unit ›› UHD/4K Support: 4096x2160 or 3840x2160 24/25/30/60hz at 4:4:4 (signals up to 18Gbps bandwidth) ›› Signal Extension: For resolution and cable quality »» 4K/UHD: Up to 250 ft. (76m) using CAT5e/CAT6/CAT6A/CAT7 »» 1080p: Up to 328 ft. (100m) maximum ›› 18 Gbps Bandwidth: High Speed / Performance for latest HDMI standards ›› High Dynamic Range (HDR) Format Support: HDR10 and Dolby® Vision ›› HDCP 2.2: Compliancy up to HDCP 2.2 and backward compliant ›› Resolution Support: Supports all SD, HD, and VESA (VGA, SVGA, XGA, WXGA, SXGA, UXGA) up to 4096x2160p ›› Deep Color Support: Up to UHD/4K 60Hz 4:2:0/12 bits, 60Hz 4:2:2/12 bits ›› Auto-Sensing: Automatic selection of newly detected source and switching from newly disconnected source via hot plug detection voltage when enabled ›› Audio De-embedder: Audio of the selected HDMI input is de-embedded at the Coax digital (PCM) and Analog L/R balanced/unbalanced connectors ›› Control Pass-Thru: 4/8 three pin phoenix connectors for bi-directional IR or RS-232 for each HDBaseT output. 4/8 IR sensors and IR emitters included. ›› Full Buffer System™: Manages TMDS re-clocking / signal re-generation, HDCP authentication to source & display, and EDID Control handshake ›› EDID: Internal library with 15 internal EDID handshakes including 4K with HDR in addition to native EDID data copied from an Output/Display 1 ›› Lossless Compressed Digital Audio: Dolby® TrueHD, Dolby® Digital Plus, DTS-HD Master Audio™, and Dolby® Atmos ›› CEC Disconnect: Prevents all device communication signals via CEC, ARC, and HDMI Ethernet channels ›› Control: Front panel buttons/LEDs, Serial IR, Optical IR, RS-232 Control, and TCP/IP Control ›› Control System Support: Key Digital® app ready. Key Digital Management Software™ Pro (KDMS™ Pro) ready, Compass Control® Pro ready. Fully controllable by all IR, RS-232, and TCP/IP supported control systems via open API. 2 ›› Key Digital® App & KDMS® Pro Ready: Scan & detect population for pre-built GUI and TCP/IP control via Key Digital® iOS App and Key Digital Management Software™ Pro (KDMS™ Pro) PC Software Accessories ›› Qty 2 power supplies: »» KD-PS80W48VD 48V/1.66A (80W) DC power jack, screw-in type ›› Rack ears and screws ›› KD-RMSWPROK remote control ›› Qty 4/8 IR Emitters ›› Qty 4/8 IR Sensors ›› Qty 5/9 3-pin terminal blocks for IR/RS-232 ›› 6-pin terminal block for analog audio ›› Quick Setup Guide Rack Mounting: ›› Secure the rack ears to each side of the KD-DA2x4G/KD-DA2x8G with the supplied hardware and then fasten the unit to the rack rails with the included machine screws. Quick Setup Guide Test for proper operation of the unit and cables in your system before permanently securing the unit for final installation. Ensure that you leave enough ventilation space to provide sufficient airflow and cooling. 1. Connect your HDMI sources to the input ports of KD-DA2x4G/KD-DA2x8G unit 2. Connect your HDMI displays to the output ports of KD-XDALRx units 3. Connect CAT wires to the KD-DA2x4G/KD-DA2x8G’s HDBaseT output and KD-XDALRx CAT5e/6 input. 4. Connect the analog audio output to an amplifier/receiver via the analog 6-pin phoenix terminals and the digital destination via the PCM output 5. Connect control system and/or PC to TCP/IP, RS-232, or place IR emitter over IR sensor. 6. Screw-in the two power supplies to the KD-DA2x4G/KD-DA2x8G’s unit, and then connect power to outlets. Both power connections are needed. 7. Power on HDMI sources and displays 8. Default static IP address: 192.168.1.239, port 23 Operate the KD-DA2x4G/KD-DA2x8G switcher via front panel buttons, IR Remote, RS-232, or TCP/IP control. 9. See TCP/IP and RS-232 Command or IR Remote Control sections for more adjustments options