KING KBP2406 Manuals

electrical mfg. company 9131 - 10th Avenue South Seattle Washington 98108 INSTALLALTION & MAINTENANCE MANUAL Hardware Needed You will need the following hardware: -Adequate gauge & length of wire for your application -Proper size fuses or breakers to handle amperage -Proper wire connectors for your application -Fasteners appropriate size to mount herater. In certain applications, conduit may be required by code. Check local electrical codes. If you want to be able to turn the heater, be sure to use flexible conduit. Mounting Height When the air flow of the heater is directed vertically or horizontally, the minimum mounting height is 6 feet in USA and 8 feet in Canada. Mounting heights depend upon building utilization and heater KW capacity. Unpack & Inspect Your New Heater Location of Heater The heater should be installed out of the reach of persons. The direction of air flow should not be restricted by machinery, beams, etc., and the air flow should wipe exposed walls, rather than blowing directly at them. When more than one heater is used in an area, the heaters should be arranged so that the air discharge of each heater supports the air flow of the others to provide best circulation of warm air. (See Air Flow Chart) WARNING Model: KBP2406 is 240 volt. It is important that you verify the power supply voltage is the same as the nameplate voltage of the heater. Improper installation or failure to follow the procedures as outlined in this manual can result in damage to the heater. Note that the KBP2406 will operate at 208 volt but will produce 25% less wattage and draw 13% less amps. Dis- connect all power from the heater at the main service panel before attempting to install or service this unit. All electrical wiring must conform to local electrical codes. Heater circuit must be properly protected. Remove the heater from the box and inspect it for any damage. Verify that you have received the mounting bracket and accesories. Tools Needed You will need the following tools to install your unit heater: Screwdriver - (Phillips & Slotted), Wire Cutters, Pliers, Adjustable Wrench, Electric Drill Locate a stud in ceiling or wall and securely fasten bracket with a minimum of two #12 fasteners 1-1/4" long. Attach heater to bracket with 3/8" x 1" wing nut & lock washer supplied. Install the lock washer between the bracket and heater, do not put lock washer on the plastic wing nut. After desired air discharge position has been determined, tighten wing nut so that heater will not pivot. Mounting Heater Distance From Walls Maintain 6" minimum clearance to side walls and 2" to ceiling in back of the heater (Air Intake Side). Maintain 18" clearance in front of the heater (Dischage Side.) Model: KBP2406 240V-1phase Unit Heater kbp2406.pm65 rev 02/03

electrical mfg. company 9131 - 10th Avenue South Seattle Washington 98108 INSTALLATION & MAINTENANCE MANUAL WARNING Model: KBP2406 is 240 volt. It is important that you verify the power supply voltage is the same as the nameplate voltage of the heater. Improper installation or failure to follow the procedures as outlined in this manual can result in damage to the heater. Note that the KBP2406 will operate at 208 volt but will produce 25% less wattage and draw 13% less Amps. Discon- nect all power from the heater at the main service panel before attempting to install or service this unit. All electrical wiring must conform to local electrical codes. Heater circuit must be properly protected. Unpack & Inspect Your New Heater Remove heater from box and inspect it for any damage. Verify you have received the mounting bracket and accessories. Tools Needed You will need the following tools to install your unit heater: -Screwdriver - (Phillips & Slotted) -Wire Cutters -Pliers -Adjustable Wrench -Electric Drill Hardware Needed You will need the following hardware: -Adequate gauge & length of wire for your application -Proper size fuses or breakers to handle amperage -Proper wire connectors for your application -Appropriate size fasteners to mount heater. In certain applications conduit may be required by code. Check local electrical codes. If you want to be able to turn the heater be sure to use flexible conduit. Mounting Height When the air flow of the heater is directed vertically or horizontally the minimum mounting height is 6 feet in USA and 8 feet in Canada. Mounting heights depend upon building utilization and heater kW capacity. Distance From Walls Maintain 6" minimum clearance to side walls and 2" to ceiling in back of the heater (air intake side). Maintain 18" clearance in front of the heater (discharge side). Mounting Heater Locate a stud in ceiling or wall and securely fasten bracket with a minimum of two #12 fasteners 1-1/4" long. Attach heater to bracket with 3/8" x 1" wingnut & lock washer supplied. Install the lock washer between the bracket and heater. Do not put lock washer on the plastic wingnut. After desired air discharge position has been determined tighten wingnut so heater will not pivot. Location of Heater The heater should be installed out-of-reach of persons. The direction of airflow should not be restricted by machinery, beams, etc. and the airflow should wipe exposed walls, rather than blowing directly at them. When more than one heater is used in an area the heaters should be arranged so that the air discharge of each heater supports the airflow of the others to provide best circulation of warm air. (see airflow chart) Model: KBP2406 240V-1phase Unit Heater 2007KBP2406.indd : 3/08