Koala Kare KB100-ST Manuals

® KOALA KARE PRODUCTS Installation and Operation Instructions KB100-ST and KB110-SSRE Baby Changing Stations Cambiador Plegable Table à Langer Babywickelstation IMPORTANT. RETAIN FOR FUTURE REFERENCE. READ CAREFULLY. IMPORTANTE. GUÁRDELO PARA FUTURAS CONSULTAS. LEER ATENTAMENTE. IMPORTANT. À CONSERVER POUR INFORMATION. À LIRE ATTENTIVEMENT. WICHTIG. ZUR SPÄTEREN BEZUGNAHME AUFBEWAHREN. BITTE SORGFÄLTIG DURCHLESEN. You are responsible for the safe operation of this unit. KB100-ST & KB110-SSRE Operating Instructions Tools Needed Hardware Provided Please Note: To assure proper installation, it is suggested that a qualified person or carpenter install the Koala Baby Changing Station. Koala Kare Products will not be responsible if the station is not installed properly. Koala Baby Changing Stations have been tested to hold a substantial static load. The unit must be attached to a permanent wall that is capable of holding a substantial load. The maximum recommended total weight for this baby changing station (including baby and parcel bag) is 60 lbs. Excessive weight may cause a hazardous or unstable condition to exist. Restraint System: To fasten the waist restraint strap, place strap around child’s midsection, and push spring tabs into buckle until both spring tabs lock in place with an audible “click”. Straps can be adjusted to make strap tighter or looser as required. Inspection Criteria: • A properly maintained baby changing station: • Opens and closes smoothly • Has both ends of a functioning, non-frayed strap: buckle clicks when closed and strap is attached to unit at both ends. • Offers parents liners through a fully stocked liner dispenser. (Dispenser built into unit.) • Provides a clean, convenient place for customers to attend to their children. gloves level drill measuring tape 1/8” (3 mm) (regular & masonry) drill bits four ¼” (6 mm) flat washers stud finder pencil Phillips head screwdriver four 1/4”x 3” (6mm x 76mm) Phillips panhead wood screws KB100-ST & KB110-SSRE Installation Instructions Step 1. Remove changing station from the shipping container and check for any freight damage. Identify the best location for installing the unit. Hold the unit in place and open the bed. Make sure you have taken the operating clearance into consideration. Step 2. Select the wall area where the unit will be installed. Measure from the floor 46½” (1181 mm) on stud center and mark the wall. Hold the unit in place to verify the alignment. Mark rough opening 35½” W x 20½” H (902 mm x 521 mm) and cut a hole in the wall with a minimum depth of 4¼” (108 mm) as measured from the finished surface of the wall (ie: tile, drywall, etc). Construct mounting frame as indicated in the illustration. If the wall surface is masonry or tile over wood studs, use caution when cutting rough opening. Step 3. Mount the unit using four ¼” x 3” wood screws through side holes as shown in illustration. Step 4. Place the unit into the recessed area and use the side mounting holes as a guide to drill a pilot hole using a 1/8” drill bit. Insert the screws and flat washers through the side mounting holes to hold the unit in place. It may be necessary to adjust the level of unit by using a shim on the top right or left side of the unit before tightening securely to the studs. Step 5. Position Koala sign (supplied) on the outside of the restroom door. Fill the built-in dispenser with sanitary bed liners. Replacement parts and additional liners can be purchased from your local distributor or by calling toll free 888.733.3456 or 303.539.8300 in the U.S.

KB100-ST and KB110-SSRE Baby Changing Station Cambiador Plegable Table à Langer Babywickeltisch Your unit can be installed to meet ADA regulations when and where applicable. Refer to Federal Register, Volume 56, No 144 28 CFR Part 36. You are responsible for the safe operation of this unit. KOALA KARE PRODUCTS Installation and Operation Instructions Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 IMPORTANT. RETAIN FOR FUTURE REFERENCE. READ CAREFULLY. IMPORTANTE. GUÁRDELO PARA FUTURAS CONSULTAS. LEER ATENTAMENTE. IMPORTANT. À CONSERVER POUR INFORMATION. À LIRE ATTENTIVEMENT. WICHTIG. ZUR SPÄTEREN BEZUGNAHME AUFBEWAHREN. BITTE SORGFÄLTIG DURCHLESEN. Please Note: To assure proper installation, it is suggested that a qualified person or carpenter install the Koala Baby Changing Station. Koala Kare Products will not be responsible if the station is not installed properly. Koala Baby Changing Stations have been tested to hold a substantial static load. The unit must be attached to a permanent wall that is capable of holding a substantial load. The maximum recommended total weight for this baby changing station (including baby and parcel bag) is 60 lbs. Excessive weight may cause a hazardous or unstable condition to exist. Restraint System: To fasten the waist restraint strap, place strap around child’s midsection, and push spring tabs into buckle until both spring tabs lock in place with an audible “click”. Straps can be adjusted to make strap tighter or looser as required. Inspection Criteria: A properly maintained baby changing station: – Opens and closes smoothly – Has both ends of a functioning, non-frayed strap: buckle clicks when closed and strap is attached to unit at both ends. – Offers parents liners through a fully stocked liner dispenser. (Dispenser built into unit.) – Provides a clean, convenient place for customers to attend to their children. TOOLS NEEDED Gloves Phillips Head Screwdriver Level Pencil Drill 1/8” Drill Bit Measuring Tape Stud Finder OPERATING INSTRUCTIONS HARDWARE PROVIDED Four ¼”x 3” Phillips Panhead Wood Screws Four ¾” x ¼” Flat Washers Step 1. Remove changing station from the shipping container and check for any freight damage. Identify the best location for installing the unit. Hold the unit in place and open the bed. Make sure you have taken the operating clearance into consideration. Step 2. Select the wall area where the unit will be installed. Measure from the floor 46½” (1181 mm) on stud center and mark the wall. Hold the unit in place to verify the alignment. Mark rough opening 35½” W x 20½” H (902 mm x 521 mm) and cut a hole in the wall with a minimum depth of 4¼” (108 mm) as measured from the finished surface of the wall (ie: tile, drywall, etc). Construct mounting frame as indicated in the illustration. If the wall surface is masonry or tile over wood studs, use caution when cutting rough opening. Step 3. The unit will be mounted using four ¼” x 3” wood screws through side holes as shown in illustration. Step 4. Place the unit into the recessed area and use the side mounting holes as a guide to drill a pilot hole using a ⅛” drill bit. Insert the screws and flat washers through the side mounting holes to hold the unit in place. It may be necessary to adjust the level of unit by using a shim on the top right or left side of the unit before tightening securely to the studs. Step 5. Position Koala sign (supplied) on the outside of the restroom door. Fill the built in dispenser with sanitary bed liners. Replacement parts and additional liners can be purchased from your local distributor Horizontal Baby Changing Station Recessed Mounted Model Numbers KB100-ST and KB110-SSRE INSTALLATION INSTRUCTIONS

Horizontal Recessed Mounted Baby Changing Station KB100-ST and KB110-SSRE INSTALLATION INSTRUCTIONS Please Note: To assure proper installation, it is suggested that a qualifi ed person or carpenter install the Koala Baby Changing Station. Koala Kare Products will not be responsible if the station is not installed properly. Koala Baby Changing Stations have been tested to hold a substantial static load. The unit must be attached to a permanent wall that is capable of holding a substantial load. Tools Needed: • Measuring Tape • Level • Flat Head and Phillips Screwdrivers • Stud Finder • Pencil • Drill • 7/32” (.56 cm) Drill Bit (regular and masonry) • 1/8” (.32 cm) Drill Bit (regular and masonry) • ½” (1.27 cm) Drill Bit (regular and masonry) Hardware Supplied: • Four ¼” x 3” (.64 cm x 7.62 cm) Panhead Wood Screws • Four ¼” x 3” (.64 cm x 7.62 cm) Phillips Panhead Machine Screws • Four ¾” x ¼” (2 cm x .64 cm) Hole Washers • Four Toggles One Restroom Sign • You are responsible for the safe operation of this unit. Inspection Criteria: A properly maintained unit: Opens and closes smoothly. • Has both ends of a functioning, non-frayed • strap: buckle clicks when closed and strap is attached at both ends of the unit. Offers parents liners through a fully stocked • liner dispenser. (Dispenser is built into unit.) Provides a clean, convenient place for • customers to attend to their children. Horizontal Strap (885) • Horizontal KB100-ST Gas Shock (874) • Horizontal KB110-SSRE Gas Shock (875) • Cream Horizontal Liner Dispenser Lid (829) • Grey Horizontal Liner Dispenser Lid (828) • Koala Restroom Door Decal (841) • Warning Label (975) • Cream Unit End Caps (692) • Grey Unit End Caps (850) • Box of Liners (KB150-99) • Using Toggles A. Insert Toggle in hole. B. Pull ring and push cap tightly against wall. C. Snap off straps. D. Install unit using screws and washers. Step 1. Remove changing station from the shipping container and check for any freight damage. Identify the best location for installing the unit. Hold the unit in place and open the bed. Make sure you have taken the operating clearance into consideration. Step 2. Select the wall area where the unit will be installed. Measure from the fl oor 44” (111.8 cm) on stud center and mark the wall. Hold the unit in place to verify the alignment. Mark rough opening 35½”” W x 20¼” H (90.2 cm x 51.4 cm) and cut a hole in the wall. Construct mounting frame as indicated in the illustration. If the wall surface is masonry or tile over wood studs, use caution when cutting rough opeining. Step 3. The unit will be mounted using four ¼” x 1½” (.64 cm x 3.84 cm) wood screws through side holes as shown in illustration. Step 4. Place the unit into the recessed area and insert the screws and fl at washers to hold the unit in place. It may be necessary to adjust the level of unit by using a shim on the top right or left side of the unit before tightening securely to the studs. Step 5. Position Koala sign (supplied) on the outside of the restroom door. Fill the built-in dispenser with sanitary bed liners. Replacement parts and additional liners can be purchased from your local distributor. Using Restraint System To fasten the waist restraint strap, place strap around child’s midsec- tion, and push spring tabs into buckles until both spring tabs lock in place with an audible “click”. Straps can be adjusted to make strap tighter or looser as required. Koala Kare Products A Division of Bobrick 6982 S. Quentin St. Centennial, CO 80112 © 2008 Koala Kare Products, Form No. AB00x July 2008 Horizontal Recessed Mounted Baby Changing Station KB100-ST and KB110-SSRE INSTALLATION INSTRUCTIONS