Koala Kare KB110-SSWM Manuals

® KOALA KARE PRODUCTS Installation and Operation Instructions KB110-SSWM Baby Changing Station Cambiador Plegable Table à Langer Babywickelstation IMPORTANT. RETAIN FOR FUTURE REFERENCE. READ CAREFULLY. IMPORTANTE. GUÁRDELO PARA FUTURAS CONSULTAS. LEER ATENTAMENTE. IMPORTANT. À CONSERVER POUR INFORMATION. À LIRE ATTENTIVEMENT. WICHTIG. ZUR SPÄTEREN BEZUGNAHME AUFBEWAHREN. BITTE SORGFÄLTIG DURCHLESEN. Your unit should be installed to meet 2010 ADA Standards for Accessible Design when and where applicable. You are responsible for the safe operation of this unit. KB110-SSWM Operating Instructions Tools Needed Hardware Provided Please Note: To assure proper installation, it is suggested that a qualified person or carpenter install the Koala Baby Changing Station. Koala Kare Products will not be responsible if the station is not installed properly. Koala Baby Changing Stations have been tested to hold a substantial static load. The unit must be attached to a permanent wall that is capable of holding a substantial load. The maximum recommended total weight for this baby changing station (including baby and parcel bag) is 60 lbs. Excessive weight may cause a hazardous or unstable condition to exist. Restraint System: To fasten the waist restraint strap, place strap around child’s midsection, and push spring tabs into buckle until both spring tabs lock in place with an audible “click”. Straps can be adjusted to make strap tighter or looser as required. Inspection Criteria: A properly maintained baby changing station should be inspected on a daily basis and parts replaced if they do not pass inspection criteria. • Has a pneumatic shock that controls the smooth opening and closing of the unit. Shock may need replacement if door opens or closes too rapidly or door doesn’t close completely. • Has both ends of a functioning, non-frayed strap: buckle clicks when closed and strap is attached to unit at both ends. • Has a warning label affixed to the product. • Offers parents liners through a fully stocked liner dispenser. (Dispenser built into unit.) • Provides a clean changing surface for customers to attend to their children. Visit koalabear.com to view list of replacement parts and videos. four ¼” (6 mm) flat washers four ¼”x 3” (6mm x 76mm) Phillips panhead wood screws gloves level drill measuring tape 7/32” (6 mm) (regular & masonry) drill bits 1/8” (3 mm) (regular & masonry) drill bits stud finder pencil Phillips head screwdriver ½” (13 mm) (regular & masonry) drill bits KB110-SSWM Installation Instructions Step 1. Remove changing station from the shipping container and check for any freight damage. Identify the best location for installing the unit. Hold the unit in place and open the bed. Make sure you have taken the operating clearance into consideration. Step 2. Determine the best method for mounting based on the type of wall. You may have left over hardware when you have finished installation. Step 3. The horizontal unit has four mounting holes provided in the back wall, positioned on a 32” (812.8 mm) stud center. If possible, locate the wood or metal wall studs for fastening the unit in the desired location. If the walls do not have studs on center as outlined, make sure at least one side of the unit is installed onto the stud. Use toggles (not supplied) for holes on the opposite side. Step 4. Find the stud where you will be attaching the left side of the unit to the wall. Measure up from the floor 44” (1118 mm), at the center of the stud, and mark the wall. Line up Hole A with the mark on the wall. Mark remaining holes using a measuring tape to make sure the holes are precisely positioned. Hold unit in place to verify. Use four ¼” x 3” (6.35 mm x 76.2 mm) panhead wood screws with washers (supplied) when wall studs are available. If the wall surface is masonry or tile over studs, use a 7/32” (5.56 mm) masonry drill bit for the pilot hole until you hit the stud. Change bit to 1/8” (3.18 mm) regular drill bit. Use four ¼” x 3” (6.35 mm x 76.2 mm) panhead wood screws with washers (supplied). If the wall has metal studs or an underlying surface of concrete block, you will need to use toggles. Additionally, if the wall has wooden studs that are not on 16” (406 mm) centers, you will need to use toggles to secure one side of the unit. The other side should be secured to the stud using the screws provided. You must allow for space inside the wall for the toggles to turn. This will vary depending on the toggles used. Step 5. Position Koala sign (supplied) on the outside of the restroom door. Fill the built-in dispenser with sanitary bed liners. Replacement parts can be purchased from your local distributor or by calling toll free 888.733.3456 or 303.539.8300 in the U.S. 2 3 KB110-SSWM ASTM F2285 (2016) ENGLISH WARNING: Never leave child unattended. WARNING: Avoid serious injury from fall­ ing or sliding out. Always use restraint system. WARNING: Designed for Infants Only. Age up to 3.5 years and weighing less than 50 lbs. Keep one hand on the child at all times. Parcels or accessory items, or both, placed on the unit may cause the unit to become unstable. FRANÇAIS ATTENTION: Ne laissez jamais un enfant sans surveillance. ATTENTION: Évitez les blessures occasionnées par une chute ou une glissade. Utilisez toujours le système de retenue. ATTENTION: Conçue uniquement pour les jeunes enfants. Jusqu’à 3 ans et demi et moins de 50 lb (23 kg). Conservez une main sur l’enfant à tout moment. Tout paquet ou accessoire placé sur la table peut créer un déséquilibre. ESPAÑOL ADVERTENCIA: No deje nunca al niño desatendido. ADVERTENCIA: Evite que el niño se lesione por caerse o resbalarse del cambiador Use siempre el sistema de sujeción. ADVERTENCIA: Diseñado exclusiva­ mente para bebés. Hasta 3 años y medio de edad y con un peso inferior a 50 libras (22,5 kg aproxi­ madamente). Mantenga siempre al niño sujeto con una mano. Colocar paquetes o accesorios, o ambas cosas, encima del cambiador puede provocar que se desestabilice. DEUTSCH WARNUNG: Das Kind niemals unbeaufsichtigt lassen. WARNUNG: Ernsthafte Verletzungen durch Herausfallen oder Herausrutschen ver­ hindern. Immer das Rückhaltesystem verwenden. WARNUNG: Dieses Produkt ist nur für Kleinkinder bis zu 3 1/2 Jahren und einem Gewicht von höchstens 50 lbs. (23 kg) vorgesehen. Das Kind immer mit einer Hand festhalten. Durch Ablegen von Päckchen und Zubehör auf der Wickelstation kann diese instabil werden.

KB110-SSWM Baby Changing Station Cambiador Plegable Table à Langer Babywickelstation ® Your unit can be installed to meet ADA regulations when and where applicable. Refer to Federal Register, Volume 56, No 144 28 CFR Part 36. You are responsible for the safe operation of this unit. KOALA KARE PRODUCTS Installation and Operation Instructions Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399 www.koalabear.com IMPORTANT. RETAIN FOR FUTURE REFERENCE. READ CAREFULLY. IMPORTANTE. GUÁRDELO PARA FUTURAS CONSULTAS. LEER ATENTAMENTE. IMPORTANT. À CONSERVER POUR INFORMATION. À LIRE ATTENTIVEMENT. WICHTIG. ZUR SPÄTEREN BEZUGNAHME AUFBEWAHREN. BITTE SORGFÄLTIG DURCHLESEN. Please Note: To assure proper installation, it is suggested that a qualified person or carpenter install the Koala Baby Changing Station. Koala Kare Products will not be responsible if the station is not installed properly. Koala Baby Changing Stations have been tested to hold a substantial static load. The unit must be attached to a permanent wall that is capable of holding a substantial load. The maximum recommended total weight for this baby changing station (including baby and parcel bag) is 60 lbs. Excessive weight may cause a hazardous or unstable condition to exist. Using Restraint System To fasten the waist restraint strap, place strap around child’s midsection, and push spring tabs into buckle until both spring tabs lock in place with an audible “click”. Straps can be adjusted to make strap tighter or looser as required. Inspection Criteria: A properly maintained baby changing station: – Opens and closes smoothly. – Has both ends of a functioning, non-frayed strap: buckle clicks when closed and strap is attached at both ends of the unit. – Offers parents liners through a fully stocked liner dispenser. (Dispenser is built into unit.) – Provides a clean, convenient place for customers to attend to their children. Measuring Tape TOOLS NEEDED Stud Finder Gloves Phillips Head Screwdriver Level Pencil Drill 1/8” Drill Bit (regular) 7/32” Drill Bit (masonry) 1/2” Drill Bit (regular and masonry) OPERATING INSTRUCTIONS HARDWARE PROVIDED Four 1/4”x 3” Phillips Panhead Wood Screws Four ¾” x ¼” Flat Washers 1 Step 1. Remove changing station from the shipping container and check for any freight damage. Identify the best location for installing the unit. Hold the unit in place and open the bed. Make sure you have taken the operating clearance into consideration. Step 2. Determine the best method for mounting based on the type of wall. You may have left over hardware when you have fi nished installation. Step 3. The horizontal unit has four mounting holes provided in the back wall, positioned on a 32” (812.8 mm) stud center. If possible, locate the wood or metal wall studs for fastening the unit in the desired location. If the walls do not have studs on center as outlined, make sure at least one side of the unit is installed onto the stud. Use toggles (not supplied) for holes on the opposite side. Step 4. Find the stud where you will be attaching the left side of the unit to the wall. Measure up from the fl oor 44” (1118 mm), at the center of the stud, and mark the wall. Line up Hole A with the mark on the wall. Mark remaining holes using a measuring tape to make sure the holes are precisely positioned. Hold unit in place to verify. Use four ¼” x 3” (6.35 mm x 76.2 mm) panhead wood screws with washers (supplied) when wall studs are available. If the wall surface is masonry or tile over studs, use a 7/32” (5.56 mm) masonry drill bit for the pilot hole until you hit the stud. Change bit to 1/8” (3.18 mm) regular drill bit. Use four ¼” x 3” (6.35 mm x 76.2 mm) panhead wood screws with washers (supplied). If the wall has metal studs or an underlying surface of concrete block, you will need to use toggles. Additionally, if the wall has wooden studs that are not on 16” (406 mm) centers, you will need to use toggles to secure one side of the unit. The other side should be secured to the stud using the screws provided. You must allow for space inside the wall for the toggles to turn. This will vary depending on the toggles used. Step 5. Position Koala sign (supplied) on the outside of the restroom door. Fill the built-in dispenser with sanitary bed liners. Replacement parts can be purchased from your local distributor or by calling toll free 888.733.3456 or 303.539.8300 in the U.S. Horizontal Baby Changing Station Surface Mounted Model Numbers KB110-SSWM INSTALLATION INSTRUCTIONS 2

continued . . . The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. KB110-SSWM Revised 7/06 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2006 by Koala Kare Products, A Division of Bobrick. Koala Kare Products A Division of Bobrick HORIZONTIAL SURFACE-MOUNTED STAINLESS STEEL FINISH BABY CHANGING STATION KB110-SSWM 35.25'' 892mm 32'' 812mm 8.25'' 210mm 9.25'' 235mm 2.5'' 64mm 20'' 508mm 33'' 838mm from floor 15.1875'' 386mm 4'' 102mm 8.25'' 206mm Floor Recommended Mounting Height Off Floor For Barrier-Free Design 44'' 1120 mm 20.0'' 508mm Recommended Mounting Height Off Floor 48'' 1283mm Finish Face of Wall ADA Compliance (when properly installed) 4.4.1 Max. Protruding Objects 4.2.5 Forward Reach 4.2.6 Side Reach 4.27.4 Operation The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. KB110-SSWM Revised 7/06 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2006 by Koala Kare Products, A Division of Bobrick. MATERIALS: 18 gauge, type 304 satin stainless steel exterior finish with FDA approved blow molded high-density polyethylene with Microban Antimicrobial additive interior. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel mounting plates and mounting hardware included. Molded in graphics and safety messages in six languages. Contoured changing surface area is 442 sq in (2873 sq mm) and comes complete with nylon safety straps and bag hooks. OPERATION: Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-density polyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance requirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99 sanitary liners. Warning: To insure that the unit supports the intended loads, baby changing stations must be properly installed accord- ing to the manufacturer’s instructions. INSTALLATION: To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of support- ing significant weight and can accommodate the supplied installation hardware. The Koala Bear Kare® Baby Changing Station meets ADA regulations when properly installed. Drilling holes and mounting the station: 1. Remove the station from the shipping container and check for any freight damage. Identify the best location for installing the baby changing station. Hold the unit in place, open the bed, and make sure that there is adequate operating clearance. 2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all of included hardware may be required for proper installation. 3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 32" stud center. If possible, locate the wood or metal wall studs for fastening the changing station in the desired location. If the walls do not have studs on the center as outlined, make sure at least one side of the unit is installed into the stud. Use toggles (supplied) for holes on the other side. 4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 45.5" (1156mm) up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole with this mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate the bottom of the station 28" (711mm) from the floor and the top of the bed at 33" (838mm) from floor. Using Wood Screws: If the wall has wood studs on 16" or 32" centers, drill 1/8" pilot holes at the marks and use the four 1/4" x 3" panhead tapping screws with supplied washers. If the wall is masonry or tile over wood studs, use a 7/32" masonry drill until you hit the stud, then proceed to drill 1/8" pilot holes into the studs and use the four 1/4" x 3" panhead tapping screws with supplied washers. Using Toggle Fasteners: If the wall has wood studs that are not on 16" or 32" centers, has metal studs, or an underlying surface of concrete block, drill with a 1/2'' masonry bit. A minimum of 2-1/2" of inside wall space is required for toggles to turn. Insert supplied toggles and tighten, locate station over toggles, then use supplied 1/4'' x 3" Phillips Panhead machine screws with supplied washers. SPECIFICATION: Baby changing station shall have 18 gauge, type 304 satin stainless steel exterior finish with high-density polyethylene with Microban Antimicrobial additive interior. Design of unit shall be surface-mounted. Unit shall be equipped with a pneumatic cylinder for controlled opening and closing of bed. Bed shall be secured to back plate with a concealed, full- length steel-on-steel hinge. Unit shall have Microban Antimicrobial embedded into plastic material. No hinge structure shall be exposed on interior or exterior surfaces. Unit shall have 11-gauge steel mounting plates with mounting hardware included. Unit shall conform to ANSI S117.1 Accessible and Usable Buildings and Facilities, ASTM F2285-04 (formerly ASTM PS125) Standard Consumer Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signs and Labels, German TUV Technical Inspection Association, ASTM G21 Antifungal and ASTM G22 Antibacterial Standards or local code if more stringent installation requirements are applicable for barrier-free accessibility. Unit shall comply with ADA regulations when properly installed. Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shall have a built-in Liner Dispenser for use with 3- ply chemical-free biodegradable sanitary liners, universal instruction graphics, and safety messages in 6 languages. Unit shall be backed by manufacturer’s 5-year limited warranty on materials and workmanship, and a 5-year replacement warranty against vandalism. Unit shall be manufactured in the U.S.A. Baby Changing Station shall be model KB110-SSWM of Koala Kare Products, A Division of Bobrick, 8962 S. Quentin St., Centennial, CO 80112 USA, Tel: 1-888-733-3456 or 303-539-8359, Web: www.koalabear.com