Kodak i100 Series Manuals

Kodak Imaging Guide Set for i100 and i200 Series Scanners This document provides instructions for installing the Kodak Imaging Guide Set for i100 and i200 Series Scanners. IMPORTANT: • It is recommended that you thoroughly clean the scanner before replacing the imaging guides. For complete cleaning procedures, see the appropriate User’s Guide for your Kodak Scanner. • Use only non-flammable cleaners such as those provided through Kodak Park Services. Do not use household cleaners. • Staticide Wipes contain isopropanol which can cause eye irritation and dry skin. Wash your hands with soap and water after performing maintenance procedures. Refer to the Material Safety Data Sheet (MSDS) for more information. The MSDS is available on the Kodak web site at www.kodak.com/go/MSDS. Instructions for Kodak i100 Series Scanners 1. Power down the scanner. 2. Access the inside of the scanner by opening the scanner cover. Replacing the Upper Imaging Guide 1. Open the door on the right side of the scanner to gain access to the upper imaging guide. 2. Locate the upper imaging guide. 3. Using a Phillips Head screwdriver, loosen the screw from the upper imaging guide bracket (slide the bracket over). 4. Pull gently on the end of the imaging guide and slowly remove it from the scanner. 5. Discard the used imaging guide. 6. Remove any dust or debris from the guide track. Do not allow debris to fall into the scanner. 7. Wipe both sides of the new upper imaging guide with a fresh Staticide Wipe. 8. Dry both sides of the new upper imaging guide with a dry Staticide Wipe. 9. Align the new upper imaging guide in the guide track and slowly push it in. 10. Realign the upper imaging guide bracket and tighten the screw. 11. Reinstall the side door. Replacing the Lower Imaging Guide 1. Locate the lower imaging guide. 2. Using a Phillips Head screwdriver, loosen the screw from the lower imaging guide and slide the imaging guide out of the bracket and remove it from the scanner. 3. Discard the used imaging guide. 4. Remove any dust or debris from the guide track. Do not allow debris to fall into the scanner. 5. Wipe both sides of the new lower imaging guide with a fresh Staticide Wipe. 6. Dry both sides of the new lower imaging guide with a dry Staticide Wipe. 7. Align the new lower imaging guide in the guide track and slowly push it in. 8. Reinstall and tighten the screw. 9. Close the scanner door. Side door Upper imaging guide

i100 Series Scanners Image Processing Guide User’s Guide A-61517

用於 i100 系列掃瞄器的 Kodak 成像導軌套件 本文件提供用於 i100 系列掃瞄器的 Kodak 成像導軌套件的安裝說明。 重要：建議您在更換成像導軌之前先徹底清潔掃瞄器。 有關完 成清潔程序的步驟，請參閱 Kodak i100 系列掃瞄器使用 手冊。 僅使用那些透過 Kodak Parts Services 取得的非易燃性 清潔劑。 請勿使用家庭清潔劑。 開啟掃瞄器 1. 關閉掃瞄器電源。 2. 從進紙器區域取出所有文件。 3. 抬起掃瞄器門釋出桿，打開掃瞄器門的閂鎖。 4. 向上拉開掃瞄器門。 更換上成像導軌 1. 開啟掃瞄器右邊的門以存取上成像導軌。 2. 找出上成像導軌。 3. 使用十字頭螺絲起子，調鬆上成像導軌扥架的螺絲 （滑開 扥架）。 4. 輕拉成像導軌的末端，將它慢慢地從掃瞄器上卸下來。 5. 丟掉用過的成像導軌。 6. 清除導軌中的灰塵或碎屑。 不要在掃瞄器中落入碎屑。 7. 使用新防靜電擦布擦拭新的上成像導軌的兩面。 8. 使用乾的防靜電擦布擦乾新的上成像導軌的兩面。 9. 將新的上成像導軌對準導軌，然後慢慢將它推入導軌。 10. 重新對準上成像導軌扥架並轉緊螺絲。 11. 安裝邊門。 更換下成像導軌 1. 找出下成像導軌。 邊門 上成像導軌