KUSSMAUL 091-269-006 Manuals

170 Cherry Avenue West Sayville, NY 11796 www.kussmaul.com Ph: 800-346-0857 Fax: 631-567-5826 [email protected] INSTRUCTION MANUAL Specifications: Operating Temp: 0 to 50°C (32 °F to 122 °F) Dimensions: 2”W x 2.5”H x 1.38”D (50.8x 63.5 x 35.2 mm) Weight: 0.125 lb. (0.05 kg) Wiring Diagram File: IM_091-269-006 Rev: A1 Revised By: PSS/jrn Date: 12-10-2019 MODEL: 091-269-006 The Auto Power Remote Panel comes with a 25-ft (7.6-m) communications cable. Important Safety Information Misusing or incorrectly connecting the remote panel may damage the equipment or create hazardous conditions for users. Read the following safety instructions and pay special attention to all Caution and Warning statements in your Auto Power Inverter Owner’s Guide. Warnings 1. All electrical work must be done in accordance with local, national, and/or inter- national electrical codes. 2. All electrical work must be done by a qualified installer. 3. Before installing or using the remote panel, read all instructions and cautionary markings located in the manual, on the Auto Power unit, and on the batteries. 4. Do not expose the remote panel to rain, snow or liquids of any type. This prod- uct is designed for indoor mounting only. 5. Use insulated tools to reduce the chance of short- circuits when installing or working with the inverter/ charger, or the batteries. 6. Remove all jewelry such as rings, bracelets, necklaces, etc., while installing this system. This will greatly reduce the chance of accidental exposure to live circuits. 7. The Auto Power Inverter/Charger contains more than one live circuit (batteries and AC power). Power may be present at more than one source. 8. he remote panel contains no user-serviceable parts. Do not attempt to repair this unit. Failure to follow these safety guidelines may cause personal injury and/or damage to the remote panel. It may also void your product warranty Mount the remote panel in a clean, dry environment. To install the remote panel: 1. Choose a location that is dry, free from cor- rosive or explosive fumes, and appropriate for installing an electronic device. 2. Using the mounting template (provided), pi- lot-drill the mounting holes. Cut an opening about 2×1.2 in. (50.8×30.5 mm) and 1.4 in. (35 mm) deep. 3. Route the communications cable inside the wall and through the opening to the Auto Power unit. 4. Connect the communications cable to the RJ11 Com Port on the back of the remote panel. 5. Select whether to enable or disable the Ignition 6. If you enable the Ignition Lockout feature, connect the remote’s red ACC wire to the vehicle’s ACC wire (12-volt connection only). Consult your vehicle’s Owner’s Manual for information. 7. Position the remote into the opening in the wall and secure it with the four screws (provided). 8. Make sure to switch the inverter OFF. 9. Plug the communications cable into the remote port (REM) on the Auto Power unit. Mounting the Unit The Auto Power Remote Panel (remote panel) can be connected to the Auto Power Inverter Charger via the Remote port on the AC/DC side panel to turn the Auto Power 2000 or 3000 Inverter Charger ON or OFF from a more convenient lo- cation. The remote panel also has the ability to enable/disable the Ignition Lockout feature of the Auto Power Inverter Char- ger. When this feature is enabled, the Auto Power Inverter Charger will shut down if The Auto Power Remote Panel (remote panel) can be connected to the Auto Power Inverter Charger via the Remote port on the AC/DC side panel to turn the Auto Pow- er 2000 or 3000 Inverter Charger ON or OFF from a more convenient location. The remote panel also has the ability to enable/ disable the Ignition Lockout feature of the Auto Power Inverter Charger. When this feature is enabled, the Auto Power Invert- er Charger will shut down if the vehicle’s ignition is not engaged (not in ACC position) to prevent unnecessary battery drain. (For AP 2000 and 3000 Inverter/Chargers) AUTO POWER REMOTE PANEL ON/OFF SWITCH