Kyocera KM-6230 Manuals

Technical Reference PRESCRIBE Commands

Command Reference PRESCRIBE Commands

Kyocera Extended Driver User Guide

IC-Link Version 2.8 User Manual User Manual Release Date 11/2004

Kyocera Extended Driver User Guide

KX Driver User Guide

INSTRUCTION HANDBOOK F-4220 ALWAYS read this Instruction Handbook thoroughly before use. After reading, maintain it in good condition and keep it together with the Instruction Handbook for your copier.

Operation Guide Manuel d'utillsation Manual de instrucciones Bedienungsanleitung Guida operativa 使用説明書 F-4730 M-2107 ALWAYS read this Operation Guide thoroughly before use. After reading, maintain it in good condition and keep it together with the Instruction Handbook for your copier. TOUJOURS lire entièrement ce Manuel d’utilisation avant d'utiliser l'appareil. Après l'avoir lu, conservez ce manuel dans de bonnes conditions avec le Manuel d'Instructions de votre copieur. Lea COMPLETAMENTE este manual de instrucciones antes de utilizar este aparato. Una vez leído, mantenga en buen estado y guárdelo junto con el manual de instrucciones de su copiadora. Lesen Sie diese Bedienungsanleitung vor der Inbetriebnahme aufmerksam durch. Achten Sie bitte darauf, die Bedienungsanleitung in gutem Zustand zu erhalten, und bewahren Sie sie zusammen mit der Bedienungsanleitung des Kopierers auf. PRIMA DELL'USO, leggere sempre, attentamente e fino in fondo, questa Guida operativa. Una volta letta, conservarla in buone condizioni insieme al Libretto di Istruzioni della copiatrice. ご使用前に必ずこの使用説明書をお読みください。お読みになった後は、複写機本体の使用説明書といっしょに 大切に保管してください。

NOTICE OF REVISION G The contents of “(1) System requirements” on page 3-4 should be revised as follows: G The explanation on the left side of page 3-10 should be revised as follows: Old title 2 Setting for the page separation and border erase modes Q New title 2 Setting for the page separation, border erase and one-page file creation modes Old sentence Touch the “2 pages” key if you want to use the page separa- tion mode and the “One page Erase” key if you want to use the border erase mode. Q New sentence Touch the “2 pages” key if you want to use the page separa- tion mode, the “One page Erase” key if you want to use the border erase mode, and the “One page per file” key if you want to use the one-page file creation mode. * Settings for the one-page file creation mode are available when sending scanning instruction from your computer. G One of the explanations in the table under “3-4 Troubleshooting” on page 3-11 should be revised as follows: G Windows 95/98/NT 4.0/2000 Operating Environment CD-ROM drive Ethernet port CPU RAM HDD IBM PC-AT or compatible Minimum 133 MHz Pentium More than 64 MB More than 20 MB One drive 10BASE-T, 100BASE-TX or 10BASE2 2 The version of the Scanner File Utility being used is not appropriate. Check with your network administra- tor to verify the appropriate version of the Scanner File Utility. Destination PC’s version is different. Connect to administra- tor. Message Procedure The version of the User File Utility being used is not appropriate. Check with your network adminis- trator to verify the appropriate version of the User File Utility. Destination PC’s version is different. Connect to administra- tor. Message Procedure Q 2000. 8 3BJ8095WA New Old 2 G The explanation under “(1) Scanning an Image Using TWAIN” on page 3-6 should be revised as follows: (1) Scanning an Image Using TWAIN There are basically two different ways to use the TWAIN standard to scanning images. The following explains these two methods. G When settings are initiated from the computer… Select the TWAIN source from the TWAIN-compatible application in your computer. The dialogue box for the TWAIN source will appear. Select the desired settings and select “Waiting Scan”. Click on the Connect button to connect to the scanner. Once your computer is connected to the scanner, the Connect button will change to the Scan button. Click on the Scan button once it appears. Set the original that you want to scan. * At this point it will be possible to perform settings in the scanner’s touch panel. Change the current settings, as desired. * The settings made in the touch panel will take precedence when settings are made in both the touch panel and the computer. Press the Start key on the scanner’s operation panel scanning of the original will begin. Once the scanning operation is complete, select whether you want to scan another original or not. If you DO want to scan another original, touch the “Continue” key and repeat steps 4 through 6. If you are finished scanning originals, touch the “End” key. G When settings are initiated at the scanner… Touch the “TWAIN” key in the basic scanning screen of the scanner’s touch panel. Set the original that you want to scan. Select the TWAIN source from the TWAIN-compatible application in Select the desired settings. Click on the Connect button to connect to the scanner. Once your computer is connected to the scanner, the Connect button will change to the Scan button. Click on the Scan button once it appears and the scanning operation will begin. 1 2 3 4 5 1 6 2 3 4 5

Please read the instruction handbook before using the copier. Keep it in the designated location for inside front cover. INSTRUCTION HANDBOOK